3. For the system shown below, determine the following (a) the reflection coefficient at the load end (b) the reflection coefficient at the source end (c) the VSWR (d) the phasor voltage at the load...

Question

Question

3. For the system shown below, determine the following (a) the reflection coefficient at the load end (b) the reflection coef

engineering Electrical-Engineering

Add a comment Improve this question Transcribed image text

Answer 1

Answer #1

3 Reflection coefficien ot Jond 21tto 2os くb) Reflection Coetti di end at Soun u end (q) 24 to レ 5 120. At , xo we hune Jod otuge at pointx omte Line from Load end o n e реак|RMS Voltage denn ut v, Cine 62 0 85 0 62 48 -J ‘2.48 28 Volt 2-J 1-1 = 60. 2 Ba -38x 2 60 So -J 122 48

Add a comment

Answer 2

Similar Homework Help Questions

3. For the system shown below, determine the following (a) the reflection coefficient at the load end (b) the reflection coefficient at the source end (c) the VSWR (d) the phasor voltage at the load...

3. For the system shown below, determine the following (a) the reflection coefficient at the load end (b) the reflection coefficient at the source end (c) the VSWR (d) the phasor voltage at the load end of the line (e) the phasor voltage at the center of the line 3. For the system shown below, determine the following (a) the reflection coefficient at the load end (b) the reflection coefficient at the source end (c) the VSWR (d) the phasor...
3. A system of two transmission lines connected in series are driven by a voltage source fi(t) Vo...

3. A system of two transmission lines connected in series are driven by a voltage source fi(t) Vou(t) and terminated by a resistive load of 60S2 as shown in the figure below. A switch is closed at t 0 and the positive voltages are measured for 5 μs giving the bounce diagram shown in the figure-the voltage values indicated in the diagram correspond to delta function weights times the source voltage products such as VOTg, VOTg(1 +「2), etc. 400 m...
#3. For the 3-phase power system shown in Fig. 3, the load is 30 kVA at...

#3. For the 3-phase power system shown in Fig. 3, the load is 30 kVA at a p.f. of 0.94 lagging. If the phasor load voltage, V. = 480/0 Compute: (i)The phasor line current, I. Ia Fig. 3 (ii) The phasor voltage Vec of the source. A . Contjo. 6). Ba [Zunet (0.1+30.6). 30 kVA hase/p. f. 0.94 las I ho o.1tjo. 652 ů 2

please answer all questions and show all steps 5) The voltage source V, below has a...

please answer all questions and show all steps 5) The voltage source V, below has a frequency of 60Hz. The load is operating at 10kVA with 0.8pf leading. The angle of the voltage across the load is 0 degrees. Assume all values are RMS. Is 0.12 500uH - 120V V eterm: Please determine the following a) The phasor Is b) The power loss in the transmission line. c) The phasor Vs d) The component (inductor or capacitor) that must be...
(30) In the circuit with a voltage source and two loads below, find the following: 2....

(30) In the circuit with a voltage source and two loads below, find the following: 2. The complex power of each load a. b. The total complex power for the two loads - note units of power in the figure c. Sketch the triangle for the total complex power e total current from the source as a phasor assuming the line voltage at the load is 20820 VRMS The value of the parallel capacitance in parallel with the two loads...
In the system shown below, thr line has a one-way transit delay of T seconds. The...

In the system shown below, thr line has a one-way transit delay of T seconds. The line is completely discharged for t ≤ 0. For the following source and component values, construct a reflection diagram for the system and plot the input voltage Vin and the load voltage VL for the time interval 0 < t < 6T. 3.6 In the system shown below, the line has a one-way transit delay of T seconds. The line is completely discharged for...

Problem: (1) For the single phase AC circuit shown below, calculate voltage phasor across the loa...

Problem: (1) For the single phase AC circuit shown below, calculate voltage phasor across the load showing amplitude and phase angle for a (reference) source voltage of 220 V and 0 degree. Also, attach your MultiSIM simulation showing the voltage amplitude across the load. Compare simulated and calculated values. Load Bus of an Industrial Facility (equivalent of Electrical Motors and power factor correction Cap in parallel). R1 L1 Vload-? 1 3.0ohm 2 10mH 3 4.7mH 4 20ohm R2 +220V, 60...
(f) the distance from the load to the first voltage maximum Use the Smith chart to...

(f) the distance from the load to the first voltage maximum Use the Smith chart to find the following quantities for the transmission line circuit shown in the accompanying figure: (a) The SWR on the line. (b) The reflection coefficient at the load. (c) The load admittance. (d) The input impedance of the line. (e) The distance from the load to the first voltage minimum. — 1= 0.41 OY "z V os = 'z Z1 = 60 + j502
A 60-Hz single-phase AC power network is shown in the figure below with four different loads. The source voltage ES-320 0. Prior to adding the capacitor load for power factor correction, the source c...

A 60-Hz single-phase AC power network is shown in the figure below with four different loads. The source voltage ES-320 0. Prior to adding the capacitor load for power factor correction, the source current IS-135 30 . Determine the capacitance (in μF) of the capacitive load that will make the power factor unity (pf 1.0) of the system. Enter the one best answer (as a number without the units) from the following choices: Sync 74 % 6 15 kVA 10...

source at 4T produce a forward wave f(r,t) = Aei(wt-Br) on a transmission line having a load at x 0. The source amplitu...

source at 4T produce a forward wave f(r,t) = Aei(wt-Br) on a transmission line having a load at x 0. The source amplitude is A = 6 and the load produces a reflection coefficient of I0.5. The wavenumber 1 rad/m, and the operating frequency is f = 107 Hz. Do the following Let a (a) Compute the simplest math form for ü(r, t), the total phasor signal on the line, for the three time values given by: (i t 0,...

3. For the system shown below, determine the following (a) the reflection coefficient at the load end (b) the reflection coefficient at the source end (c) the VSWR (d) the phasor voltage at the load...

Homework Answers