Question

Associate Simulation (CSWA-S) Question 13 of 20 D0 13: After running a study, some material properties, oads and fixtures were modified. What needs to be done to reflect this change on the results? No Picture for this Question O Only re-run the study to update the results O Re-mesh the model and re-run the study O Only re-mesh the model; the results will then automatically update O Only rebuild the model in SolidWorks Show Summary O Reset Question Next Question Previous Question .1.0.1501 О -114:04 5:5 Associate Simulation (CSWA-S) Question 14 of 20 D040: As a result of an applied load, 2 plates, initially separated by a small clearance gap, come in contact with each other. The type of contact condition that must be employed between the plates to solve this problem correctly in SolidWorks Simulation is: No Picture for this Question O No need to define anything: The program will detect the contact automaticallyNode to surface or Surface to surface No Penetration contact and take it into account Shrink fit contact O Bonded contact Show Summary O Reset Question Next Question Previous Question .1.0.1501 О 6:16 -113:44 Associate Simulation (CSWA-S) Question 15 of 20 D096: Is cyclic symmetry another name for axisymmetry? No Picture for this Question O Yes O No Show Summary O Reset Question Next Question Previous Question .1.0.1501 113:29 Associate Simulation (CSWA-S) Question 16 of 20 D124: Which of the following geometries can be meshed using beam elements? There can be more than one answer C. Previous Quetion o 642 O Reset Question Show Summary Next Question .1.0.1501 -113:18 Associate Simulation (CSWA-S) Question 17 of 20 For 3 points: D132: A thin sheet metal plate is stiffened by structural Thin Plate members as shown. How will you set up this model? Structural members O Mesh the thin plate with shells and define the structural members as beams O Mesh the thin plate with shells and define the structural members as beams. Define a bonded contact type between each structural member and the shell surface Define a rigid connector between each structural member and the shell surface Previous Question Show Summary Next Question Reset Question 8.1.0.1501 113:09 Associate Simulation (CSWA-S) Question 18 of 20 DOS1: The result values at specific locations (nodes) in a model in SolidWorks Simulation. tool can be used to determine the No Picture for this Question O Probe O Section OClipping O Iso surface Show Summary ←Previous Question D Reset Question Next Question → .1.0.1501 112:59 O 701 7:01 Associate Simulation (CSWA-S) Question 19 of 20 D053: To avoid any misinterpretation of the results, after performing a static analysis with gap/contact elements the scale factor for plots should be set No Picture for this Question O Equal to 1 O Less than 1 O To the maximum displacement value of the model Equal to 0 O Show Summary Next Question Previous Question Reset Question .1.0.1501 O 713 112:47 Associate Simulation (CSWA-S) Question 20 of 20 D065: The Default plots for the SolidWorks Simulation esults, setup under SolidWorks Simulation Options, allows you to: No Picture for this Question O Automatically load results upon opening the SolidWorks file O Select plots that you want the program to generate automatically in the Simulation study tree after running a study. O Control the display of the results folder in the Simulation study tree O None of the other anwers is correct Show Summary ← Previous Question O Reset Question Next Question .1.0.1501 -112:36 7:24 а к Question 8 of 20 For 3 points D144: ls it possible to simulate the crushing of a ping pong ball in a static analysis in SolidWorks Simulation? O Yes O No

Answer 1

ns. 13 Onlky re-up the study to update the results ns4 Node to suaface o sface to sus feae No Penetrcution contact Ans 15 No Ans L c