Homework Answers
Add Answer to:
Assume Kr 1 and Ka In a journal bearing assembly, the shaft has a diameter of 88.900 mm and a bilateral tolerance of + 0.076 mm. The bushing bore diameter is 89.027 mm with a unilateral toleran...
A journal bearing has a shaft diameter of 78.00 mm with a unilateral tolerance of -0.02...
A journal bearing has a shaft diameter of 78.00 mm with a unilateral tolerance of -0.02 mm. The bushing bore has a diameter of 78.10 mm with a unilateral tolerance of 0.06 mm. The bushing is 36 mm long and supports a load of 2 kN. The journal speed is 720 rev/min. For the minimum clearance assembly find the minimum film thickness, the heat loss rate, and the maximum lubricant pressure for SAE 10 and SAE 30 lubricants operating at...
A journal bearing has a shaft diameter of 75.00-mm with a unilateral tolerance of -0.02 mm....
A journal bearing has a shaft diameter of 75.00-mm with a unilateral tolerance of -0.02 mm. The bushing bore has a diameter of 75.10 mm with a unilateral tolerance of 0.06 mm. The bushing is 36 mm long and supports a load of 2 kN. The journal speed is 720 rpm. For the minimum clearance assembly find the minimum film thickness and the maximum lubricant pressure for SAE 20 and SAE 40 lubricants operating at an average film temperature of...
A journal bearing has a shaft diameter of 75mm with a unilateral tolerance of -0.02mm.The bushing bore has a diameter of...
A journal bearing has a shaft diameter of 75mm with a unilateral tolerance of -0.02mm.The bushing bore has a diameter of 75.10mm with a unilateral tolerance of 0.06mm.The bushing is 36mm long and supports a load (W) 1898 N.The journal speed (N) is 600 rev/min.For the minimum clearance assembly find the minimum film thickness,the heat loss rate, and the maximum lubricant pressure for SAE 60 at an average film temperature of 70 C.
5) [10] A journal bearing has a journal diameter of 75 mm with a unilateral tolerance...
5) [10] A journal bearing has a journal diameter of 75 mm with a unilateral tolerance of - 0.075 mm. The bushing bore has a diameter of 75.15 mm and a unilateral tolerance of 0.1 mm. The busing is 75 mm long and supports a 2585 N load. The journal speed is 750 rev/min. Find the minimum oil film thickness and the maximum film pressure for SAE 20W lubricant at an operating temperature of 65 °C for the minimum clearance...
6. A journal bearing has shaft with a diameter of 75 mm. The bushing bore is 75.1 mm and the bushing is 37.5 mm long and supports a load of 2 kN. The journal Speed is 720 RPM. Find the minimum film t...
6. A journal bearing has shaft with a diameter of 75 mm. The bushing bore is 75.1 mm and the bushing is 37.5 mm long and supports a load of 2 kN. The journal Speed is 720 RPM. Find the minimum film thickness, the heat loss rate is SAE 20 oil and the operating temperature is 60 C.
6. A journal bearing has shaft with a diameter of 75 mm. The bushing bore is 75.1 mm and the bushing is...
A full journal bearing has a journal with a diameter of 2.000 in and a unilateral...
A full journal bearing has a journal with a diameter of 2.000 in and a unilateral tolerance of -0.0012 in. The bushing has a bore with a diameter of 2.0024 in and a unilateral tolerance of 0.002 in. The bushing is 1 in long and supports a load of 600 lbf at a speed of 800 rev/min. Find the minimum film thickness, maximum film pressure, coefficient of friction and total lubricant flow if the average film temperature is 130°F and...
The shown values are incorrect 2 out of 3 attem A full journal bearing has a...
The shown values are incorrect
2 out of 3 attem A full journal bearing has a shaft journal diameter of 25 mm with a unilateral tolerance of -0.01 mm. The bushing bore has a diameter of 25.04 mm with a unilateral tolerance of 0.03 mm. Thelid ratio is unity. The bushing load is 1.05 kN, and the journal rotates at 1,200 rev/min. Analyze the minimum clearance assembly if the average viscosity is 50 mPa.s to fin the minimum oil film...
For the following data for full journal bearing: Shaft diameter of 75.00 mm with a unilateral...
For the following data for full journal bearing: Shaft diameter of 75.00 mm with a unilateral tolerance of -0.02 mm. • The bushing bore has a diameter of 75.10 mm with a unilateral tolerance of 0.06 mm. • The bushing is 37.5 mm long Supports a load of 2 kN. The journal speed is 1000 rev/min. A decision needs to be made by a designer on choosing the lubricant operating at an average film temperature of 60°C. However, his decision...
Problem 1: Based on problem 12-15 on textbook: You are asked to perform design assessment of...
Problem 1: Based on problem 12-15 on textbook: You are asked to perform design assessment of a journal bearing using minimum radial clearance for a load of 2700 N. Use Trumpler's criteria and assume that both l/d and α are unity. The bearing has the following specification: natural-circulation pillow-block bearing journal diameter of 62.5mm with a unilateral tolerance of-0.025 mm. bushing bore diameter is 62.6 mm with a unilateral tolerance of 0.1 mm. shaft runs at an angular speed of...
3. A 100 mm diameter shaft is supported by a bearing 50 mm long with a...
3. A 100 mm diameter shaft is supported by a bearing 50 mm long with a minimum oil-film thickness of 0.02 mm and radial clearance of 0.06 mm. It is lubricated by SAE 30 oil. The bearing carries a load of 4 kN of at 900 rpm. Employing the design charts, determine The temperature of the oil film • • The coefficient of friction • The friction power
A journal bearing has a shaft diameter of 78.00 mm with a unilateral tolerance of -0.02 mm. The bushing bore has a diameter of 78.10 mm with a unilateral tolerance of 0.06 mm. The bushing is 36 mm long and supports a load of 2 kN. The journal speed is 720 rev/min. For the minimum clearance assembly find the minimum film thickness, the heat loss rate, and the maximum lubricant pressure for SAE 10 and SAE 30 lubricants operating at...
A journal bearing has a shaft diameter of 75.00-mm with a unilateral tolerance of -0.02 mm. The bushing bore has a diameter of 75.10 mm with a unilateral tolerance of 0.06 mm. The bushing is 36 mm long and supports a load of 2 kN. The journal speed is 720 rpm. For the minimum clearance assembly find the minimum film thickness and the maximum lubricant pressure for SAE 20 and SAE 40 lubricants operating at an average film temperature of...
5) [10] A journal bearing has a journal diameter of 75 mm with a unilateral tolerance of - 0.075 mm. The bushing bore has a diameter of 75.15 mm and a unilateral tolerance of 0.1 mm. The busing is 75 mm long and supports a 2585 N load. The journal speed is 750 rev/min. Find the minimum oil film thickness and the maximum film pressure for SAE 20W lubricant at an operating temperature of 65 °C for the minimum clearance...
6. A journal bearing has shaft with a diameter of 75 mm. The bushing bore is 75.1 mm and the bushing is 37.5 mm long and supports a load of 2 kN. The journal Speed is 720 RPM. Find the minimum film thickness, the heat loss rate is SAE 20 oil and the operating temperature is 60 C.
6. A journal bearing has shaft with a diameter of 75 mm. The bushing bore is 75.1 mm and the bushing is...
The shown values are incorrect
2 out of 3 attem A full journal bearing has a shaft journal diameter of 25 mm with a unilateral tolerance of -0.01 mm. The bushing bore has a diameter of 25.04 mm with a unilateral tolerance of 0.03 mm. Thelid ratio is unity. The bushing load is 1.05 kN, and the journal rotates at 1,200 rev/min. Analyze the minimum clearance assembly if the average viscosity is 50 mPa.s to fin the minimum oil film...
For the following data for full journal bearing: Shaft diameter of 75.00 mm with a unilateral tolerance of -0.02 mm. • The bushing bore has a diameter of 75.10 mm with a unilateral tolerance of 0.06 mm. • The bushing is 37.5 mm long Supports a load of 2 kN. The journal speed is 1000 rev/min. A decision needs to be made by a designer on choosing the lubricant operating at an average film temperature of 60°C. However, his decision...
Problem 1: Based on problem 12-15 on textbook: You are asked to perform design assessment of a journal bearing using minimum radial clearance for a load of 2700 N. Use Trumpler's criteria and assume that both l/d and α are unity. The bearing has the following specification: natural-circulation pillow-block bearing journal diameter of 62.5mm with a unilateral tolerance of-0.025 mm. bushing bore diameter is 62.6 mm with a unilateral tolerance of 0.1 mm. shaft runs at an angular speed of...
3. A 100 mm diameter shaft is supported by a bearing 50 mm long with a minimum oil-film thickness of 0.02 mm and radial clearance of 0.06 mm. It is lubricated by SAE 30 oil. The bearing carries a load of 4 kN of at 900 rpm. Employing the design charts, determine The temperature of the oil film • • The coefficient of friction • The friction power
Most questions answered within 3 hours.
-
A solid, uniform disk of radius 0.250 m and mass 53.7 kg rolls
down a ramp...
asked 1 hour ago -
Given the following table of high speed internet access vs.
annual home income:
Home Income
%...
asked 2 hours ago -
A baseball batter hits a 0.145kg baseball straight up into the
air. The baseball leaves the...
asked 2 hours ago -
An FM modulator is tested using
single-tone baseband signal with frequency of 50kHz and a sprectrum...
asked 3 hours ago -
Write the ionic equations for the first stage of salts
hydrolysis.
Anion, Cation?
Na2S
NiSO4
K2SO4...
asked 4 hours ago -
suppose there is a normally distributed population with a mean of
250 and a standard deviation...
asked 5 hours ago -
Question Three
Suppose you as project manager are using the Waterfall
development methodology on a large...
asked 6 hours ago -
Which statement is not true about welfare in Canada?
A.Benefits typically vary based on one's ability...
asked 7 hours ago -
Please help me with FLOWCHART and UML diagram for class,
thank you!
#include <iostream>
#include <fstream>...
asked 7 hours ago -
3. Describe the “logic circuit” of the Lac operon. Which
proteins are bound or not to...
asked 7 hours ago -
Ayesha’s adjusted gross income is $60,000 in 2019. She donated a
piece of artwork with a...
asked 7 hours ago -
For Dijkstra’s shortest path algorithm:
a. Give the Big-O time for Dijkstra’s shortest path algorithm
and...
asked 8 hours ago