A journal bearing has a shaft diameter of 75mm with a unilateral tolerance of -0.02mm.The bushing bore has a diameter of...
A journal bearing has a shaft diameter of 75mm with a unilateral tolerance of -0.02mm.The bushing bore has a diameter of 75.10mm with a unilateral tolerance of 0.06mm.The bushing is 36mm long and supports a load (W) 1898 N.The journal speed (N) is 600 rev/min.For the minimum clearance assembly find the minimum film thickness,the heat loss rate, and the maximum lubricant pressure for SAE 60 at an average film temperature of 70 C.
Homework Answers
Add Answer to:
A journal bearing has a shaft diameter of 75mm with a unilateral tolerance of -0.02mm.The bushing bore has a diameter of...
A journal bearing has a shaft diameter of 78.00 mm with a unilateral tolerance of -0.02...
A journal bearing has a shaft diameter of 78.00 mm with a unilateral tolerance of -0.02 mm. The bushing bore has a diameter of 78.10 mm with a unilateral tolerance of 0.06 mm. The bushing is 36 mm long and supports a load of 2 kN. The journal speed is 720 rev/min. For the minimum clearance assembly find the minimum film thickness, the heat loss rate, and the maximum lubricant pressure for SAE 10 and SAE 30 lubricants operating at...
A journal bearing has a shaft diameter of 75.00-mm with a unilateral tolerance of -0.02 mm....
A journal bearing has a shaft diameter of 75.00-mm with a unilateral tolerance of -0.02 mm. The bushing bore has a diameter of 75.10 mm with a unilateral tolerance of 0.06 mm. The bushing is 36 mm long and supports a load of 2 kN. The journal speed is 720 rpm. For the minimum clearance assembly find the minimum film thickness and the maximum lubricant pressure for SAE 20 and SAE 40 lubricants operating at an average film temperature of...
5) [10] A journal bearing has a journal diameter of 75 mm with a unilateral tolerance...
5) [10] A journal bearing has a journal diameter of 75 mm with a unilateral tolerance of - 0.075 mm. The bushing bore has a diameter of 75.15 mm and a unilateral tolerance of 0.1 mm. The busing is 75 mm long and supports a 2585 N load. The journal speed is 750 rev/min. Find the minimum oil film thickness and the maximum film pressure for SAE 20W lubricant at an operating temperature of 65 °C for the minimum clearance...
A full journal bearing has a journal with a diameter of 2.000 in and a unilateral...
A full journal bearing has a journal with a diameter of 2.000 in and a unilateral tolerance of -0.0012 in. The bushing has a bore with a diameter of 2.0024 in and a unilateral tolerance of 0.002 in. The bushing is 1 in long and supports a load of 600 lbf at a speed of 800 rev/min. Find the minimum film thickness, maximum film pressure, coefficient of friction and total lubricant flow if the average film temperature is 130°F and...
Assume Kr 1 and Ka In a journal bearing assembly, the shaft has a diameter of 88.900 mm and a bilateral tolerance of + 0.076 mm. The bushing bore diameter is 89.027 mm with a unilateral toleran...
Assume Kr 1 and Ka In a journal bearing assembly, the shaft has a diameter of 88.900 mm and a bilateral tolerance of + 0.076 mm. The bushing bore diameter is 89.027 mm with a unilateral tolerance of +0:0.119 mm. The bushing length is 50 mm. The SAE 30 oil has an average operating temperature 60°C. For a minimum radial clearance, a speed of 1000 rev/min, and a radial load of 20 kN, find the maximum bearing pressure and its...
For the following data for full journal bearing: Shaft diameter of 75.00 mm with a unilateral...
For the following data for full journal bearing: Shaft diameter of 75.00 mm with a unilateral tolerance of -0.02 mm. • The bushing bore has a diameter of 75.10 mm with a unilateral tolerance of 0.06 mm. • The bushing is 37.5 mm long Supports a load of 2 kN. The journal speed is 1000 rev/min. A decision needs to be made by a designer on choosing the lubricant operating at an average film temperature of 60°C. However, his decision...
6. A journal bearing has shaft with a diameter of 75 mm. The bushing bore is 75.1 mm and the bushing is 37.5 mm long and supports a load of 2 kN. The journal Speed is 720 RPM. Find the minimum film t...
6. A journal bearing has shaft with a diameter of 75 mm. The bushing bore is 75.1 mm and the bushing is 37.5 mm long and supports a load of 2 kN. The journal Speed is 720 RPM. Find the minimum film thickness, the heat loss rate is SAE 20 oil and the operating temperature is 60 C.
6. A journal bearing has shaft with a diameter of 75 mm. The bushing bore is 75.1 mm and the bushing is...
The shown values are incorrect 2 out of 3 attem A full journal bearing has a...
The shown values are incorrect
2 out of 3 attem A full journal bearing has a shaft journal diameter of 25 mm with a unilateral tolerance of -0.01 mm. The bushing bore has a diameter of 25.04 mm with a unilateral tolerance of 0.03 mm. Thelid ratio is unity. The bushing load is 1.05 kN, and the journal rotates at 1,200 rev/min. Analyze the minimum clearance assembly if the average viscosity is 50 mPa.s to fin the minimum oil film...
A 3-inch diameter ground shaft rotates at 1000 rev/min in a lathe turned full journal bearing,...
A 3-inch diameter ground shaft rotates at 1000 rev/min in a lathe turned full journal bearing, which is 3 in long. SAE Grade 20 lubricant is used and the lubricant sump has a steady-state temperature of 100°F. The maximum lubricant temperature must not exceed 200°F. Analyze the assembly assuming average clearance and a H8/f8 clearance fit. Determine the following: a. The maximum radial load that the journal can carry and still operate under thick-film lubrication conditions. (6 points) b. The...
PROBLEM 2 and 3 (journal bearing) A gear-reduction unit uses the countershaft depicted in the figurel....
PROBLEM 2 and 3 (journal bearing) A gear-reduction unit uses the countershaft depicted in the figurel. The reactions at bearing positions and C, are shown in figure 2. Note that only bearing position take the axial load. The bearing at position is to be angular-contact ball bearings, having a desired life of 50 kh when used at 300 rev/min. Use 1.2 for the application factor and a reliability goal for the bearing pair of 0.96, assuming distribution data from manufacturer...
A journal bearing has a shaft diameter of 78.00 mm with a unilateral tolerance of -0.02 mm. The bushing bore has a diameter of 78.10 mm with a unilateral tolerance of 0.06 mm. The bushing is 36 mm long and supports a load of 2 kN. The journal speed is 720 rev/min. For the minimum clearance assembly find the minimum film thickness, the heat loss rate, and the maximum lubricant pressure for SAE 10 and SAE 30 lubricants operating at...
A journal bearing has a shaft diameter of 75.00-mm with a unilateral tolerance of -0.02 mm. The bushing bore has a diameter of 75.10 mm with a unilateral tolerance of 0.06 mm. The bushing is 36 mm long and supports a load of 2 kN. The journal speed is 720 rpm. For the minimum clearance assembly find the minimum film thickness and the maximum lubricant pressure for SAE 20 and SAE 40 lubricants operating at an average film temperature of...
5) [10] A journal bearing has a journal diameter of 75 mm with a unilateral tolerance of - 0.075 mm. The bushing bore has a diameter of 75.15 mm and a unilateral tolerance of 0.1 mm. The busing is 75 mm long and supports a 2585 N load. The journal speed is 750 rev/min. Find the minimum oil film thickness and the maximum film pressure for SAE 20W lubricant at an operating temperature of 65 °C for the minimum clearance...
Assume Kr 1 and Ka In a journal bearing assembly, the shaft has a diameter of 88.900 mm and a bilateral tolerance of + 0.076 mm. The bushing bore diameter is 89.027 mm with a unilateral tolerance of +0:0.119 mm. The bushing length is 50 mm. The SAE 30 oil has an average operating temperature 60°C. For a minimum radial clearance, a speed of 1000 rev/min, and a radial load of 20 kN, find the maximum bearing pressure and its...
For the following data for full journal bearing: Shaft diameter of 75.00 mm with a unilateral tolerance of -0.02 mm. • The bushing bore has a diameter of 75.10 mm with a unilateral tolerance of 0.06 mm. • The bushing is 37.5 mm long Supports a load of 2 kN. The journal speed is 1000 rev/min. A decision needs to be made by a designer on choosing the lubricant operating at an average film temperature of 60°C. However, his decision...
6. A journal bearing has shaft with a diameter of 75 mm. The bushing bore is 75.1 mm and the bushing is 37.5 mm long and supports a load of 2 kN. The journal Speed is 720 RPM. Find the minimum film thickness, the heat loss rate is SAE 20 oil and the operating temperature is 60 C.
6. A journal bearing has shaft with a diameter of 75 mm. The bushing bore is 75.1 mm and the bushing is...
The shown values are incorrect
2 out of 3 attem A full journal bearing has a shaft journal diameter of 25 mm with a unilateral tolerance of -0.01 mm. The bushing bore has a diameter of 25.04 mm with a unilateral tolerance of 0.03 mm. Thelid ratio is unity. The bushing load is 1.05 kN, and the journal rotates at 1,200 rev/min. Analyze the minimum clearance assembly if the average viscosity is 50 mPa.s to fin the minimum oil film...
A 3-inch diameter ground shaft rotates at 1000 rev/min in a lathe turned full journal bearing, which is 3 in long. SAE Grade 20 lubricant is used and the lubricant sump has a steady-state temperature of 100°F. The maximum lubricant temperature must not exceed 200°F. Analyze the assembly assuming average clearance and a H8/f8 clearance fit. Determine the following: a. The maximum radial load that the journal can carry and still operate under thick-film lubrication conditions. (6 points) b. The...
PROBLEM 2 and 3 (journal bearing) A gear-reduction unit uses the countershaft depicted in the figurel. The reactions at bearing positions and C, are shown in figure 2. Note that only bearing position take the axial load. The bearing at position is to be angular-contact ball bearings, having a desired life of 50 kh when used at 300 rev/min. Use 1.2 for the application factor and a reliability goal for the bearing pair of 0.96, assuming distribution data from manufacturer...
Most questions answered within 3 hours.
-
A 0.035 mol sample of a weak acid, HA, is dissolved in 437 mL of
water...
asked 48 seconds from now -
a sample of Ar gas has a volume of 6.30 L with an unknown
pressure. the...
asked 6 seconds from now -
The
serum cholesterol levels of a population of kids follow a normal
distribution with mean 155...
asked 19 minutes ago -
han discusses the racist practice of badlands, a bar
in the Castro
district of San Francisco,...
asked 31 minutes ago -
A sample of final exam scores is normally distributed with a
mean equal to 25 and...
asked 35 minutes ago -
An investor shorts 100 shares of a stock when the share price is
$50 and closes...
asked 39 minutes ago -
LLOP corporation just paid 4$ dividend per share, you expect the
dividend to grow 8% for...
asked 48 minutes ago -
if we subtract 1000 from 0001 is there overflow? (binary)
asked 56 minutes ago -
Hello, I need help with the function below, The language I am
using is Ocaml
open...
asked 58 minutes ago -
Explain how the presence of glucose represses the gal structural
genes?
asked 1 hour ago -
For the reaction CaI2+2AgNO3⟶2AgI+Ca(NO3)2 how many grams of
silver iodide, AgI, are produced from 56.5 g...
asked 1 hour ago -
Write an equation for hydrolysis via acid catalysis.
Using ethyl acetate, ethyl benzoate, ethyl formate or...
asked 1 hour ago