Homework Answers
Add Answer to:
Problem 3 (20 points) A cross-flow heat exchanger consists of a bundle of 32 tubes in a long duct. Hot water at 150°C and a mean velocity of 0.5 m/s enters the tubes having inner and outer diameters...
Problem 2: Heat exchanger (25 points) Cold water (op 4179 J/kg K) enters the tubes of a heat exchanger at 20 °C at a rate of 3 kgs. while hot oil (cp 2200 J/kg.K) enters the shell at 130 C at the sam...
Problem 2: Heat exchanger (25 points) Cold water (op 4179 J/kg K) enters the tubes of a heat exchanger at 20 °C at a rate of 3 kgs. while hot oil (cp 2200 J/kg.K) enters the shell at 130 C at the same mass flow rate and leaves at 60°C The heat exchanger consistsoftwo shells and 20 tubes, each executing four passes (two passes per shell). If the W/m2-K, assume the tube wall is very thin with convective heat transfer...
A simple counter flow heat exchanger consists of two co-axial tubes with hot process water passing...
A simple counter flow heat exchanger consists of two co-axial tubes with hot process water passing through the inner tube and clean water through the annular space between the inner and outer tubes. The clean water enters at 20°C and leaves at 50°C. The process water enters at 90°C and leaves at 40°C. The mass flowrate of the process water is 3 kgs-1. The inner tube diameter is 30 mm and the outer tube diameter is 50 mm. Take the...
The condenser of a large steam power plant is a heat exchanger in which steam is...
The condenser of a large steam power plant is a heat exchanger in which steam is condensed to liquid water. Assume the condenser to be a shell-and-tube heat exchanger consisting of a single shell and 30,000 tubes, each executing two passes (see figure below). The tubes are of thin wall construction with D=25mm, and steam condenses on their outer surface with an associated convection coefficient ho=11,000W/ m K The heat transfer rate that must be effected by the heat exchanger...
PROBLEM 3 (45 points) The condenser of a large steam power plant is a heat exchanger...
PROBLEM 3 (45 points) The condenser of a large steam power plant is a heat exchanger in which steam is condensed to liquid water. Assume the condenser to be a parallel flow shell-and-tube heat exchanger consisting of a single shell and 1x10 tubes, each executing two passes. The inner diameter of tubes is D = 50 mm and its thickness is 5 mm (Do not ignore the thickness). The steam condenses on their outer surface. Thermal conductivity of the tube...
this is the full problem. 11.1 An industrial boiler consists of tubes inside of which flow hot combustion gases. Water...
this is the full problem.
11.1 An industrial boiler consists of tubes inside of which flow hot combustion gases. Water boils on the exterior of the tubes. When installed, the clean boiler has an over- all heat transfer coefficient of 300 W/m2- K. Based on experience, it is anticipated that the fouling factors on the inner and outer surfaces will increase linearly with time as Rat and R = at where a;= 2.5 x 10-1" m2- K/Ws and a =...
Water enters through a thick-walled tube having inner and outer diameters of 19 and 38 mm and 20 m long
Water enters through a thick-walled tube having inner and outer diameters of 19 and 38 mm and 20 m long The inlet temperature is Tmi=17℃ and outlet temperature is Tmo = 50°C. The outer surface of the tube is well Insulated, and electrical heating within the wall provides for a uniform generation rate of q = 8X105 W/m3. If the inner surface temperature of the tube Ts = 60 °C at the outlet what is the local convection heat transfer...
PROBLEM #3 (30 points) A shell-and (N 20) is used to heat vegetable oil on the shell side using hot water on tethat side. is Lp- 3.0 m). Each copper tube has dimensions of 15.56-mm ID and 19.05-...
PROBLEM #3 (30 points) A shell-and (N 20) is used to heat vegetable oil on the shell side using hot water on tethat side. is Lp- 3.0 m). Each copper tube has dimensions of 15.56-mm ID and 19.05-mm OD and thermal conductivity of copper is 390 W/m-K. Water at a total flow rate of 3.33 kg/s enters the tubes of the heat exchanger at 360 K and leaves at 300 K The inlet and outlet temperatures of oil are 290...
please do 11.33 11.32 A single-pass, cross-flow heat exchanger uses hot exhaust gases (mixed) to heat...
please do 11.33
11.32 A single-pass, cross-flow heat exchanger uses hot exhaust gases (mixed) to heat water (unmixed) from 30 to 80°C at a rate of 3 kg/s. The exhaust gases, hav- ing thermophysical properties similar to air, enter and exit the exchanger at 225 and 100°C, respectively. If the overall heat transfer coefficient is 200 W/m2.K, estimate the required surface area. 11.33 Consider the fluid conditions and overall heat transfer coefficient of Problem 11.32 for a concentric tube heat...
A concentric tube heat exchanger for cooling lubricating oil consists of a thin-walled inner tube of...
A concentric tube heat exchanger for cooling lubricating oil
consists of a thin-walled inner tube of 25 mm diameter carrying
water and an outer tube of 45 mm diameter carrying the oil. The
exchanger operates in countercurrent flow with an overall heat
transfer coefficient of 55 W/m2 K and the tabulated average
properties given below. Mass flow rates of oil and water are both
0.1 kg/s, oil enters the exchanger at 100°C, and water enters the
exchanger at 30°C. (a)...
Water at an average velocity of 3.5 m/s flows through a 5-m-long stainless steel tube (k...
Water at an average velocity of 3.5 m/s flows through a 5-m-long stainless steel tube (k = 14.2 W/m °C) in a boiler. The inner and outer diameters of the tube are Di = 1.0 cm and Do = 1.4 cm, respectively. If the convection heat transfer coefficient at the outer surface of the tube where boiling is taking place is ho = 8400 W/m2 • °C, determine product of the overall heat transfer coefficient Ui by the inner surface...
Problem 2: Heat exchanger (25 points) Cold water (op 4179 J/kg K) enters the tubes of a heat exchanger at 20 °C at a rate of 3 kgs. while hot oil (cp 2200 J/kg.K) enters the shell at 130 C at the same mass flow rate and leaves at 60°C The heat exchanger consistsoftwo shells and 20 tubes, each executing four passes (two passes per shell). If the W/m2-K, assume the tube wall is very thin with convective heat transfer...
A simple counter flow heat exchanger consists of two co-axial tubes with hot process water passing through the inner tube and clean water through the annular space between the inner and outer tubes. The clean water enters at 20°C and leaves at 50°C. The process water enters at 90°C and leaves at 40°C. The mass flowrate of the process water is 3 kgs-1. The inner tube diameter is 30 mm and the outer tube diameter is 50 mm. Take the...
The condenser of a large steam power plant is a heat exchanger in which steam is condensed to liquid water. Assume the condenser to be a shell-and-tube heat exchanger consisting of a single shell and 30,000 tubes, each executing two passes (see figure below). The tubes are of thin wall construction with D=25mm, and steam condenses on their outer surface with an associated convection coefficient ho=11,000W/ m K The heat transfer rate that must be effected by the heat exchanger...
PROBLEM 3 (45 points) The condenser of a large steam power plant is a heat exchanger in which steam is condensed to liquid water. Assume the condenser to be a parallel flow shell-and-tube heat exchanger consisting of a single shell and 1x10 tubes, each executing two passes. The inner diameter of tubes is D = 50 mm and its thickness is 5 mm (Do not ignore the thickness). The steam condenses on their outer surface. Thermal conductivity of the tube...
this is the full problem.
11.1 An industrial boiler consists of tubes inside of which flow hot combustion gases. Water boils on the exterior of the tubes. When installed, the clean boiler has an over- all heat transfer coefficient of 300 W/m2- K. Based on experience, it is anticipated that the fouling factors on the inner and outer surfaces will increase linearly with time as Rat and R = at where a;= 2.5 x 10-1" m2- K/Ws and a =...
PROBLEM #3 (30 points) A shell-and (N 20) is used to heat vegetable oil on the shell side using hot water on tethat side. is Lp- 3.0 m). Each copper tube has dimensions of 15.56-mm ID and 19.05-mm OD and thermal conductivity of copper is 390 W/m-K. Water at a total flow rate of 3.33 kg/s enters the tubes of the heat exchanger at 360 K and leaves at 300 K The inlet and outlet temperatures of oil are 290...
please do 11.33
11.32 A single-pass, cross-flow heat exchanger uses hot exhaust gases (mixed) to heat water (unmixed) from 30 to 80°C at a rate of 3 kg/s. The exhaust gases, hav- ing thermophysical properties similar to air, enter and exit the exchanger at 225 and 100°C, respectively. If the overall heat transfer coefficient is 200 W/m2.K, estimate the required surface area. 11.33 Consider the fluid conditions and overall heat transfer coefficient of Problem 11.32 for a concentric tube heat...
A concentric tube heat exchanger for cooling lubricating oil
consists of a thin-walled inner tube of 25 mm diameter carrying
water and an outer tube of 45 mm diameter carrying the oil. The
exchanger operates in countercurrent flow with an overall heat
transfer coefficient of 55 W/m2 K and the tabulated average
properties given below. Mass flow rates of oil and water are both
0.1 kg/s, oil enters the exchanger at 100°C, and water enters the
exchanger at 30°C. (a)...
Water at an average velocity of 3.5 m/s flows through a 5-m-long stainless steel tube (k = 14.2 W/m °C) in a boiler. The inner and outer diameters of the tube are Di = 1.0 cm and Do = 1.4 cm, respectively. If the convection heat transfer coefficient at the outer surface of the tube where boiling is taking place is ho = 8400 W/m2 • °C, determine product of the overall heat transfer coefficient Ui by the inner surface...
Most questions answered within 3 hours.
-
Here is a pair of aromatic compounds that each have a complicated
set of aromatic peaks....
asked 10 minutes ago -
As with many public goods, determining the appropriate level of
government support for the production of...
asked 13 minutes ago -
Write a balanced chemical equation for the oxidation reaction
between Caro’s acid (H2SO5) and CN– ion...
asked 16 minutes ago -
Calculate the number of valence electrons for
[Mo(C6H6)(CO)3]
asked 27 minutes ago -
Which of the following are true about the strength of the
association between two variables?
1-...
asked 23 minutes ago -
You are a monopolist and know that your consumers have a linear
demand curve. At what...
asked 22 minutes ago -
Raising a heavy load requires work. Raising it in half the time
requires:
asked 29 minutes ago -
MGT-201: Marketing Management
Before deciding on the structure of the channel marketers must
take several factors...
asked 28 minutes ago -
1. ACLs allow a router to control traffic within a network. The
concept is very similar...
asked 30 minutes ago -
35. When the electron in a hydrogen atom falls from its first
excited energy level to...
asked 32 minutes ago -
A man is dragging a box of mass "m" by using a rope which rests
on...
asked 48 minutes ago -
Liquid octane
(CH3(CH2)6CH3) will
react with gaseous oxygen (O2) to produce gaseous carbon
dioxide (CO2) and...
asked 49 minutes ago