Water (density 998 kg/m', absolute viscosity 1.12x10 Ns/m2) is pumped from a lake into a reservoir at a rate of 0.7 m/s. The water flows through a re-entrant opening, a valve, and a sharp-edge...
Water, with density of 1000 kg/m3 and kinematic viscosity of 1.0 x 10- m2/s, is pumped through a total length of 60 m of pipe from a lower reservoir to a higher reservoir. The inner diameter of the pipe is 30 cm. Both reservoirs are open to the atmosphere, and the water surface of the higher reservoir is 10 m above that of the lower reservoir. The entrance from the lower reservoir to the pipe is sharp-edged, and along the...
Water (density 998 kg/mº, dynamic viscosity 0.001 Pa s) is pumped between two reservoirs at a volumetric flow rate of 0.006 m/s through a 120-m long pipe of 5 cm diameter. The roughness ratio of the pipe is a/d = 0.001. There are some fittings and valves in the pipe system, as shown in Figure Q1. The loss coefficients of the valves and fittings can be found in Table Q1. The Darcy friction factor can be found in the Moody...
ater (density 1000 kg/m3, viscosity 0.001 N-s/m2) flows from a large reservoir through straight pipe into the atmosphere at a flowrate of 2.5 m3/s. The reservoir is pressurized to 200 kPa (gage). The pipe has a diameter of 0.5 m and absolute roughness of 0.1 mm. The pipe also contains a turbine that has an efficiency of 0.6. si A) Is the flow in the pipe laminar or turbulent? (3 pts) B) What is the power transmitted from the turbine...
Problem 4 (50 points) water is discharged from a reservoir at a rate of 18.103 m2/s using two horizontal cast iron pipes nected in series and a pump between them. The first pipe is 20 m long and has a 6-cm diameter, while the second pipe is 35 m long and has a 4-cm diameter. The water level in the reservoir is 30 m above the centerline of the pipe. The pipe entrance is sharp-edged. Losses associated with the connection...
Water is being pumped from reservoir A to reservoir F through a 30-m long PVC pipe (e 0) of diameter 0.150 m. There is an open gate valve located at C; 90 bends (threaded) located at B. D and E; and a pump shown with the letter P. The pump is required to deliver 0.25 m'/s of water to reservoir F from A. NOTE: p. 1000 kg/m. y=9.80 kN/m, v= 1.12 x 10 m/s L-30-m to' -0.25m %2 10 m...
1. Water is pumped from a low reservoir to a high reservoir that is 20 m higher in elevation. The water is flowing at 1.5 m/s through a 305 mm internal diameter piping system. The water is at 18 degrees C. There are 1,000 m of piping, six standard 45 degree bends, two standard 90 degree bends, a branch flow tee, three gate valves, a swing check valve, a square inlet and a square outlet. The piping and valves are...
Water (p=998kg/m^3, u=0.001Pa*s) flows from reservoir A to reservoir B through the piping system shown. Each elbow has a minor loss coefficient of 1.2. Each valve has a minor loss coefficient of 3.2. The entrance and exit are both sharp edged. Determine the flow rate L/min. You now need to modify the piping system to increase the flow rate to 100L/min by reducing the length of the 25mm pipe. What must new length of the 25mm pipe be? 86. Water...
Q3 (40 pts): Water is pumped through a 60-m-long, 0.3-m-diameter pipe from a lower reservoir to a higher reservoir, which has a water surface 10 m above the lower one. When the pump adds 40 kW to the water the flowrate is 0.20 m/s. Assume the following coefficients of minor losses: • Entrance: Kentrance = 0.5 Exit: Kexit = 1 Each elbow: Kelbow = 1.5 • Valve: K= 6 Part A (20 pts) Determine the pipe roughness ε. Part B...
Water (density = 1000 kg/m3, viscosity = 1.15 x 10-3 N-s/m2) is delivered from a large reservoir upstream (Section"1") through two mortar lined steel circular pipes arranged in series to another large reservoir downstream (Section "2") as shown in Figure E4.7 The upstream pipe is 80 m long and 0.15 m in diameter, whereas the downstream pipe is 50 m long and 0.1 m in diameter. Both pipes have sharp-edged entrance and exit. Consider both major and minor losses. Determine...
fluid mechanics ASAP please Problem 4 (50 points) Water is discharged from a reservoir at a rate of 18.103 m3/s using two horizontal cast iron pipes connected in series and a pump between them. The first pipe is 20 m long and has a 6-cm diameter, while the second pipe is 35 m long and has a 4-cm diameter. The water level in the reservoir is 30 m above the centerline of the pipe. The pipe entrance is sharp-edged. Losses...