Problem 3 [201 Calculate land power dissipated by 5 K Ω resistor for the amplifier (ideal) 10 ΚΩ 1ov 5V Problem 4 Find...
PROBLEM 5 (15 Points) Compute the power dissipated across the 6 Ohms resistor. Use source transformation to reduce the circuit to only one large loop. You may have to use it a few times. 6 t e 12 511 201 40 v
120 Problem 1, Use the node-voltage method to find the steady state expression for v () in the circuit shown. The sinusoidal sources are v,-35cos 50 t V'and i 20 sin 50 1 A 20 Ω 0 Problem 2 120) Use the mesh-current method to find the steady state expression for velt) in the circuit shown. Answer must be in time domain. Below excitation voltage v is given in time domain v(t) 0.75 V,<t 2 Ω ) 5osin(40140°) Problem 3...
Problem 3 (10 pts.) In the following circuit, operational amplifiers are ideal. Find vol and Vo2 and, Psk (power absorbed by the 5 k2 resistor. 15νο -- 0,1 0.5 kΩ ξ2 kΩ 1Ονο -- 0,2 35 kΩ <0.4 kΩ ξ1 ΚΩ Ground
Problem 1) [15 marks] The gain of the dual-op-axap instrumentation amplifier shown in Fig. 1 can be adjusted by the variable resistor Ro. The op-amps are ideal. atu Fig. 1 a)Show that v.-2(1 RG )(v2-v.). b Specify suitable components to have a variable gain from 10 to 100 V/V. Problem 2) [15 marks] a) Design an op-amp limiter circuit for amplitude control with the transfer characteristic of Fig. 2(a). Use +-15V DC sources to power the circuit. Assume Vo-0.7 V...
can you solve this 5 problem please Q2. Using voltage divider and/or current divider to find the unknown on each of the circuits: 40 V -) ) ξR, υ ξR, 6 Ω 20 Ωξυ, 2.4A 1) 1890 Ω ξ10Ω 10 Ω ξ5 kΩ 360 kΩ 45 VI + υ, ξ 20 kΩ ξ90 ΚΩ Q3. Using a Y to delta transformation find the currents il, i2, and i3. And the power delivered by the source. 56 Ω 44Ω 80 Ω...
2- Set the two independent power sources to Vsi 6V and Veo" 10 V and measure their actual values using the DMM. Actual Values of power sources: 4.47 VS15.99 Vs- 3- Using the breadboard construct the circuit shown in Figure 4,1 (repeated below for convenience). Use the resistors measured in Step 1 (above) and the power sources Vsi- 6 V, and Vs2 -10 V. IR3 IRI RS. R5 R1 R3 Va V4 V2 V1 ww ww It 12 R4 R23...
Problem 3: Design Problem On Figure P3a, you have a Common Source (CS) n-channel MOSFET amplifier. Notice the absence of a source resistor Rsig and load resistor R. If we know how the present amplifier (the one on Figure P3a) behaves without Rsig and RL, we can infer its behaviors if Rsig and R were to be added. design the amplifier circuit on Figure P3a, i.e., you have to find appropriate values for RGj You are to RG,, RD, and...