Feel free to ask if you have any query.Thank you.
hi can you sovle this problem and do the matlab code please. thanks Problem #1 From ECE 102 Engineering Computation...
please do this problem in matlab and show me the code. Thanks. please do this problem in matlab and show me the code. Thanks. please do this problem in matlab and show me the code. Thanks. please do this problem in matlab and show me the code. Thanks. please do this problem in matlab and show me the code. Thanks.please do this problem in matlab and show me the code. Thanks. please do this problem in matlab and show me...
please do this problem in matlab and show me the code. Thanks. please do this problem in Matlab and show me the code. Thanks. Problem #1: Circuits and linear-systems In the last HW you developed the governing equations for the “Wheatstone”-bridge circuit used extensively in engineering applications (shown below). B R R2 A D G m RA с E The resulting equations were solved for the output voltage and currents using the function: function [V_out, I_vector] =Wheatstone_bridge (v_in, R_vector) In...
can you sovle this problem, also I need the code for part d. thanks Problem #5 Ri Vy= Probe I R- 1502 o VOLTMETER INPUT CIRCUIT Probe 2 Express resistance in ohms (2) and voltage in volts (V) Requirements-Part 1 (voltmeter not attached yet) a) Suppose you want to produce a voltage of 1 V across resistor R2 (i.e. Vor 1 V) Use the voltage divider equation to find the value of Ri that is needed to do this. b)...
Can you help me with this question please? For the code, please do it on MATLAB. Thanks 7. Bonus [3+3+4pts] Before answering this question, read the Google page rank article on Pi- azza in the 'General Resources' section. The Google page rank algorithm has a lot to do with the eigenvector corresponding to the largest eigenvalue of a so-called stochastic matrix, which describes the links between websites.2 Stochastic matrices have non-negative entries and each column sums to1, and one can...
I have no idea what to do. Can you please include the code with it? Thanks! 2. The trajectory motion of a projectile is given as a function of time. x(t) = (V, cost 1 y(t) = (v, sin(O)t - 5 gta where x is the horizontal distance or down range of the projectile in feet y is the vertical motion or height of the projectile in feet ve is the initial velocity = 200 ft/s O is the angle...
can you answer both #1 (a&B) and #2 please 1. Write MATLAB code to do the following: (4 pts) a) Find the area of the circles where r=[7, 8, 10] using A = tr2 b) Find the distance traveled by a ball falling in the air is given by the equation x=x0+vot+ at?. Calculate the position of the ball at time t = 5s, XO = 10m, vo= 15 m/s, and a = 9.81 m/sec^2. Write MATLAB code to accomplish...
please solve then upload matlab code Thanks 1. The function f(z, y) (a-x)2 + b(y-12)2 is called Rosenbrock's banana function. It is often used as a benchmarking test for optimization algorithms becatse it is easy to find the minimum by hand but often very difficult to find numerically. Throughout the problem, we will use the values a = 2 and b 10. You can plot this function using the following code: x3:0.1:3; y = -10:0.2:10; Cx,Ymeshgrid(x,y); Z(2-X).2 10* (Y-X. 2)....
I have all of the answers to this can someone just actually explain this matlab code and the results to me so i can get a better understanding? b) (c) and (d) %% Matlab code %% clc; close all; clear all; format long; f=@(t,y)y*(1-y); y(1)=0.01; %%%% Exact solution [t1 y1]=ode45(f,[0 9],y(1)); figure; plot(t1,y1,'*'); hold on % Eular therom M=[32 64 128]; T=9; fprintf(' M Max error \n' ); for n=1:length(M) k=T/M(n); t=0:k:T; for h=1:length(t)-1 y(h+1)=y(h)+k*f(t(h),y(h)); end plot(t,y); hold on %%%...
please write a MATLAB code to solve this problem, all parts from a to d have to be solved in matlab. Thank you u The 26-in. drum rotates about a horizontal -7.5 rad/sec axis with a constant angular velocity Q 7.5 rad/s. The small block A has no motion relative to the drum surface as it passes the bottom position 0 0. r-13 a) Determine the coefficient of static friction that would result in block slippage at an angular position...
Hi I need help understanding this matlab code. Can you add comments or at least state what the lines in this code are doing. Thanks! close all; clear all;clc; t=1:0.025:5; desired=5*sin(2*3.*t); noise=5*sin(2*50*3.*t); refer=5*sin(2*50*3.*t+ 3/20); primary=desired+noise; subplot(4,1,1); plot(t,desired); ylabel('desired'); subplot(4,1,2); plot(t,refer); ylabel('refer'); subplot(4,1,3); plot(t,primary); ylabel('primary'); order=2; mu=0.005; n=length(primary) delayed=zeros(1,order); adap=zeros(1,order); cancelled=zeros(1,n); for k=1:n, delayed(1)=refer(k); y=delayed*adap'; cancelled(k)=primary(k)-y; adap = adap + 2*mu*cancelled(k) .* delayed; delayed(2:order)=delayed(1:order-1); end subplot(4,1,4); plot(t,cancelled); ylabel('cancelled');