Provide detailed solution with assumptions.
Provide detailed solution with assumptions. Rainwater flows through the galvanised iron downspout shown in Figure 4 at...
Part 1 Correct. Water flows through a horizontal, pipe bend as is illustrated in the figure below. The flow cross section area is constant at a value of 9000 mm2. The flow velocity everywhere in the bend is 15 m/s. The pressures at the entrance and exit of the bend are 210 and 149 kPa, respectively. Calculate the horizontal (x and y) components of the anchoring force needed to hold the bend in place (a) What is the density of...
Question 4
Water flows in a sand filter, shown in the figure below. The
cross section is 400 in2 and flow rate is 6.5 x
10-4 ft3/sec. What is the velocity,
V?
QUESTION 4 Water flows in a sand filter, shown in the figure below. The cross section is 400 in2 and flow rate is 6.5 x 10-4 fsec. What is the velocity, V? Inflow Overflow Water Water Sand Filter 5 ft. —_ k * O a. 7.1 x 10-5...
thermaldynamics and fluid mechanics
Question 4 An orifice plate flow meter, as shown in figure Q4, is situated in a horizontal pipe of 95 cm diameter (d) in which water flows. The pressure difference between the vena contracta and flow upstream at point 1 is measured using a differential manometer. The diameter of the sharp-edged orifice (d.) is 35 cm. The coefficient of discharge for the flow meter is 0.7, and the coefficient of contraction is 0.62. Assume the density...
pls
write down clearly thanks
-2 SKMM2313 QUESTION 1 (a) A compressible fluid flows through a compressor that increases the density from 1 kg/m2 to 5 kg/m. The cross-sectional area of the inlet pipe is 3 m2 and that of the discharge pipe is 1 m2. Determine the relation between the discharge velocity V2 and the inlet velocity Vi (2 marks) In Figure Q1, determine the rate of change of h(t) if the fluid is water. (b) Take V.-10 m/s...
Figure 4 Water pipes taking water from
Trawsfynydd Lake to Maentwrog hydroelectric power station
Question 3
This question is worth 12 marks.
The water from the lake in Question 2 flows along the river and
enters a hydroelectric power plant through large inlet pipes with a
circular cross-section of internal diameter , similar to those
shown in Figure 4.
Figure 4 Water pipes taking water from
Trawsfynydd Lake to Maentwrog hydroelectric power station
a.Explain why the velocity of the water...
b) A portion of a solenoid is shown as in Figure Q3(b). The magnetic circuit comprises of cast iron yoke, sheet steel plunger, cast steel plunger and air gaps. The yoke and plunger have a cross section area of 4.8x10 m´and 4.5x10m respectively. A coil is wound on the center of the yoke. The effective length of the cast iron yake, sheet steel plunger and cast steel plunger are la = 0.25 m; 4 = 0.12 m and l =...
please solve with details
Question#1140Marksl The shaft shown in the figure is rotating at 650 rpm and it receives 5592.75 W through a flexible coupling at its right end. The power is delivered to an adjacent shaft through a single helical gear B having a normal pressure angle of 20° and a helix angle of 15o. The pitch diameter for the gear is 105.1814 mm (4.141 in). A spacer is used to position the gear relative to bearing C. The...
A bridge is supported by two types of rectangular cross-section piles located in a river as shown in Figure 1. The width of the piles is w -0.5 m and their lengths are either lı- 2 m or l2-2.5 m. The river of depth of about 20 m runs at 2 m/s. Water density is p 1000 kg/m3 and its absolute viscosityH 1.00 x 10-3 N.s/m2. You are asked to perform dimensional analysis to find the drag force on the...
A bridge is supported by two types of rectangular cross-section piles located in a river as shown in Figure 1. The width of the piles is w - 0.5 m and their lengths are either l 2 m or 12 2.5 m. The river of depth of about 20 m runs at 2 m/s. Water density is p 1000 kg/m and its absolute viscosity 1.00 x 10-3 N.s/m2 You are asked to perform dimensional analysis to find the drag force...