6.) A selected pump operates at 1750 rpm and delivers 4135 gpm at 248 feet of head with a 16-inch impeller. The design of the system requires that the pump deliver only 3700 gpm. What is the new impeller diameter to meet the design flow rate?
6.) A selected pump operates at 1750 rpm and delivers 4135 gpm at 248 feet of head with a 16-inch impeller. The design o...
Please answer question 7:
A centrifugal pump discharges 500 GPM through a 12-inch diameter
impeller. The fluid leaves the impeller with a
tangential velocity of 17 ft/sec. If water, @ 68°F,
enters the impeller via radial flow (I.E. no whirl), and the inner
radius and thickness of the impeller are
1.75-inches. (Assume a constant thickness of the
impeller) and if the pump speed is 1775 rpm, with a head loss of
4.5-feet. What is the horsepower input to the flow by
the pump?
QUESTION...
4.45 A two-tank pump/pipe system has a head requirement of 23.4 ft at a flow rate of 100 gpm. The elevation difference between the fluid surfaces in the tanks is 10 ft. The pump is a Bell & Gossett Series e-80 Model 2.5x2.5x9C operating at 1170 rpm with a 7.5-inch impeller. a. Develop an cquation for the system curve. b. Use a computer program to develop an equation for the 7.5-inch impeller using data read from the pump performance curve...
02. centrifugal pump draws benzene at 25°C (sp. weight of benzene 8.59 kN/m) om a tank whose level is 2.6 m below the pump inlet. The atmospheric pressure (abs). The head loss in the suction piping due to friction and minor osses is 0.8 N.m /N. The vapor pressure of benzene is 13.3 kPa (abs). Determine he available net positive suction head (NPSH) and tell f it is acceptable or not. (10 points) Discharge ine Flew 2.6 m What is...
#1 plz
HW24 、049 wish to design a pumping system with an effective head (total dynamic head - TDH is to be 90 gpm. a. If the system is lossless what is the required input power in Watts? b. If the system has an efficiency of 58% what is the input power in Watts? 2. Recall the system layout at the top of Page 1 in WS24. The input electrical power is 2600 W. The motor is an induction motor...
Q4. A pump draws water from a large reservoir and delivers it to another reservoir whose water surface is 10 m higher than the pump centreline and that the pump is 1.5 meter above the suction reservoir. The total suction and deliver pipe used is 21.1 m in length, 9 cm in diameter and has a Darcy friction factor f0.0339. The pump operates at 750 rpm and its characteristic performances are given in table below: Q (m3 s H (m)15...
theavton the ump.if the absolute pressure of the liquid drops below the vapor pressure then cavitation will occur Answer B) False A) True A centrifugal pump delivers water against a net head of 20 meters and a design speed of 1100 rpm. is 10 m/s. he impeller diameter is 0.4 m. Determine manometric efficiency of the pump, if Co2 Intr E) 95% D) 92% A) 85% C) 90% B) 88% Answer In Calculate net head or effective head for Pelton...
1. Water at 100°F is pumped from a sea-level reservoir to a tank open to the atmosphere through a new 14-in ID galvanized iron pipe as shown below. The minor loss coefficients in the suction and discharge piping are EK = 1.5 and Eduk = 7.2. Perform the following: a. derive the equation for the system curve as hy = a + b where he and a have units of feet and b has units of ft/gpm); b. plot the...
1/9 1 Piping system (14 points) Water is pumped from a reservoir to a large receiver vessel which is maintained at p4 6 bar (absolute) through the operation of the pump and a high pressure nitrogen supply that bleeds into the tank through a regulator. The water enters through an opening at the top of the vessel. A drain is provided at the low point in the system. Elevations are as shown. All valves are gate valves (k = 0.15)...
1/9 1 Piping system (14 points) Water is pumped from a reservoir to a large receiver vessel which is maintained at p4 6 bar (absolute) through the operation of the pump and a high pressure nitrogen supply that bleeds into the tank through a regulator. The water enters through an opening at the top of the vessel. A drain is provided at the low point in the system. Elevations are as shown. All valves are gate valves (k = 0.15)...
10. Write a one-page summary of the attached paper? INTRODUCTION Many problems can develop in activated sludge operation that adversely affect effluent quality with origins in the engineering, hydraulic and microbiological components of the process. The real "heart" of the activated sludge system is the development and maintenance of a mixed microbial culture (activated sludge) that treats wastewater and which can be managed. One definition of a wastewater treatment plant operator is a "bug farmer", one who controls the aeration...