Power Electronics and Drive Systems
Homework Answers
Add Answer to:
Power Electronics and Drive Systems a) A boost converter is required to have an output voltage of 8 V and supply a l...
2. Renewable energy system requires a boost converter with input voltage variation of 18 V to 42 ...
2. Renewable energy system requires a boost converter with input voltage variation of 18 V to 42 V (de) and gives output of 120 V at 0.6 kW. For the converter the switching frequency is set at 50 kHz. a) Find the operating duty cycle range for each switch of the converter0 marks b) 196 What is the inductor value which should keep inductor current variation below under all input voltages [30 marks] c) Find the capacitor value which should...
A boost converter has an input of 5 V and an output of 25 W at...
A boost converter has an input of 5 V and an output of 25 W at 15 V. The minimum inductor current must be no less than 50 percent of the average. The output voltage ripple must be less than 1 percent. The switching frequency is 300 kHz. Determine the duty ratio, minimum inductor value, and minimum capacitor value.
A Buck-boost converter has an output voltage 100 V, output power 60 W and input voltage...
A Buck-boost converter has an output voltage 100 V, output power 60 W and input voltage 12 V. Switching frequency is 15 kHz. Calculate duty ratios for the switch and the diode. Find values for the inductor L and capacitor C, when the allowed output voltage ripple is ±0.15 % and the inductor current ripple is ±1 % (of the average value). If the on-time of the switch has an inaccuracy of ±50 ns, what is the new output voltage...
1) (6 points) It is desired to design a 50 W buck-boost converter to regulate its...
1) (6 points) It is desired to design a 50 W buck-boost converter to regulate its output voltage at 26V from a solar panel whose output voltage varies between 20 and 40 V. The desired switching frequency is 20 kHz. The ripple current in the inductor should remain within +/-0.1 A, and the output voltage ripple should not exceed +/- 2%. a. Determine the duty cycle range for operating this converter. b. Design this buck-boost converter by finding lower limits...
Design a boost converter power stage to the following specification: Input voltage Output voltage: Output voltage...
Design a boost converter power stage to the following specification: Input voltage Output voltage: Output voltage ripple:max 20mV Load power: Switching frequency: 15kHz 110-125V 300V 1.5kW Calculate: (i) Maximum duty cycle (ii) Minimum duty cycle (iii) Average diode current (iv) Assuming the Rds(on) of the MOSFET is 0.01 Ω, and the diode forward voltage is 0.8V, calculate the approximate efficiency of the circuit. 2. A switching power supply shown in the circuit below has its switch driven by a signal...
a9a resistive load. Inductor 3-(35 pts) Design a converter that has an input voltage of 24 V DC and supplies 18 V DC to current is desired to be continuous and must not change more than 30 % of i...
a9a resistive load. Inductor 3-(35 pts) Design a converter that has an input voltage of 24 V DC and supplies 18 V DC to current is desired to be continuous and must not change more than 30 % of its average value voltage ripple must be lower than 2 %. Switching frequency is 10 kHz. a) Draw the circuit diagram. Calculate the duty ratio. Calculate values for 2 desired conditions of the inductor current and determine the value of the...
A boost regulator has an input voltage of Vs = 5V. The average output voltage Va=...
A boost regulator has an input voltage of Vs = 5V. The average output voltage Va= 15 V and the average load current la = 0.5A. The switching frequency is 25 KHz. If L = 0.15 mH and C = 220uF. Determine: the duty factor, the ripple current of inductor, the peak current inductor, the ripple voltage of filter capacitance, the critical values of L. Plot the waveforms for the source current, inductor current, filter capacitor current, capacitance voltage, and...
18 marks load with a power of 25.6 W.The cy f is 40kHz. sign a buck-boost converter to produce an output voltage of 16V a put voltage ripple must not exceed 1%. The dc input voltage is 24V. Th e swit...
18 marks load with a power of 25.6 W.The cy f is 40kHz. sign a buck-boost converter to produce an output voltage of 16V a put voltage ripple must not exceed 1%. The dc input voltage is 24V. Th e switching frequen 121 a) the duty ratio b) Find the size of the inductor so that the maximum inductor current c) the size of the capacitor d) Assume L=1 00μH and the switching frequency fis variable. 141 121 Lma 10A...
Afs 4. Design a Buck-Boost Converter to convert 10 vdc to -20 vdc, using the switching...
Afs 4. Design a Buck-Boost Converter to convert 10 vdc to -20 vdc, using the switching frequency of 50 kHz for a load resistance of 50 22. (a) What is the duty ratio, D? (b) What is the minimum value for the inductor to be utilized? (C) Assuming to utilize an inductor with double the minimum value, determine the maximum inductor current. (d) For an output voltage ripple of 3%, determine the value of the output capacitor, non
A buck converter is used to have low output voltage from the high input source to...
A buck converter is used to have low output voltage from the high input source to low output voltage. The estimated power output is at 25 kW with the switching frequency of 25 kHz. Design the buck converter as by finding and following specifications consider the ripple of the output is set at 1% (i) Calculate the duty ratio of the buck converter (1 mark) (ii) Determine the minimum requirement for the inductor and the capacitor (5 marks) (iii) Determine...
2. Renewable energy system requires a boost converter with input voltage variation of 18 V to 42 V (de) and gives output of 120 V at 0.6 kW. For the converter the switching frequency is set at 50 kHz. a) Find the operating duty cycle range for each switch of the converter0 marks b) 196 What is the inductor value which should keep inductor current variation below under all input voltages [30 marks] c) Find the capacitor value which should...
1) (6 points) It is desired to design a 50 W buck-boost converter to regulate its output voltage at 26V from a solar panel whose output voltage varies between 20 and 40 V. The desired switching frequency is 20 kHz. The ripple current in the inductor should remain within +/-0.1 A, and the output voltage ripple should not exceed +/- 2%. a. Determine the duty cycle range for operating this converter. b. Design this buck-boost converter by finding lower limits...
Design a boost converter power stage to the following specification: Input voltage Output voltage: Output voltage ripple:max 20mV Load power: Switching frequency: 15kHz 110-125V 300V 1.5kW Calculate: (i) Maximum duty cycle (ii) Minimum duty cycle (iii) Average diode current (iv) Assuming the Rds(on) of the MOSFET is 0.01 Ω, and the diode forward voltage is 0.8V, calculate the approximate efficiency of the circuit. 2. A switching power supply shown in the circuit below has its switch driven by a signal...
a9a resistive load. Inductor 3-(35 pts) Design a converter that has an input voltage of 24 V DC and supplies 18 V DC to current is desired to be continuous and must not change more than 30 % of its average value voltage ripple must be lower than 2 %. Switching frequency is 10 kHz. a) Draw the circuit diagram. Calculate the duty ratio. Calculate values for 2 desired conditions of the inductor current and determine the value of the...
A boost regulator has an input voltage of Vs = 5V. The average output voltage Va= 15 V and the average load current la = 0.5A. The switching frequency is 25 KHz. If L = 0.15 mH and C = 220uF. Determine: the duty factor, the ripple current of inductor, the peak current inductor, the ripple voltage of filter capacitance, the critical values of L. Plot the waveforms for the source current, inductor current, filter capacitor current, capacitance voltage, and...
18 marks load with a power of 25.6 W.The cy f is 40kHz. sign a buck-boost converter to produce an output voltage of 16V a put voltage ripple must not exceed 1%. The dc input voltage is 24V. Th e switching frequen 121 a) the duty ratio b) Find the size of the inductor so that the maximum inductor current c) the size of the capacitor d) Assume L=1 00μH and the switching frequency fis variable. 141 121 Lma 10A...
Afs 4. Design a Buck-Boost Converter to convert 10 vdc to -20 vdc, using the switching frequency of 50 kHz for a load resistance of 50 22. (a) What is the duty ratio, D? (b) What is the minimum value for the inductor to be utilized? (C) Assuming to utilize an inductor with double the minimum value, determine the maximum inductor current. (d) For an output voltage ripple of 3%, determine the value of the output capacitor, non
A buck converter is used to have low output voltage from the high input source to low output voltage. The estimated power output is at 25 kW with the switching frequency of 25 kHz. Design the buck converter as by finding and following specifications consider the ripple of the output is set at 1% (i) Calculate the duty ratio of the buck converter (1 mark) (ii) Determine the minimum requirement for the inductor and the capacitor (5 marks) (iii) Determine...
Most questions answered within 3 hours.
-
True/False Questions
1.
In interpreting an agreement, courts generally apply a
subjective standard.
2.
If, after...
asked 42 seconds ago -
4. Determine the theoretical yield of P2O5, when 3.07 g of P
reacts with 6.09 g...
asked 12 minutes ago -
On January 1, 20X7, Green Corp. paid $1,020,000 to acquire Wax
Co. Wax maintained separate incorporation....
asked 1 hour ago -
S sells property with a $500 basis to B for $450, and B later
sells the...
asked 1 hour ago -
C++
Write a class Fraction that defines adding, subtracting,
multiplying, and dividing fractions by overloading standard...
asked 2 hours ago -
This java code won't run and I can't figure out the problem with
it. Please help...
asked 3 hours ago -
Trace the following recursive methods:
a) isPal with the string “abccda”
b) isAnBn with the string...
asked 4 hours ago -
1. Which of the following is false about photosynthesis?
A. ATP is the molecule used to...
asked 5 hours ago -
A simple random sample of size n=64 is obtained from a
population with a mean of...
asked 6 hours ago -
(2 dimensions, 1 object, 2 accelerations)
1) A projectile is thrown with a wind. The wind...
asked 6 hours ago -
Brian makes $34,100 per year. How much can Brian expect to
contribute to FICA taxes in...
asked 7 hours ago -
To buy a new house you must borrow $155,000. To do this you take
out a...
asked 7 hours ago