If the allowable shear stress for each of the 0.30- in.-diameter steel pins at A, B, and C is tau allow = 12.5 ksi, an...
A Review The allowable bending stress is allow = 24 ksi and the allowable shear stress is Tollow = 14 ksi 8 kip/It 6 ft Part A Select the lightest-weight wide-lange beam with the shortest depth from Appendix B that will safely support the loading shown Part A Select the lightest-weight wide-flange beam with the shortest depth from Appendix B that will safely support the loading shown. W12 X 16 W12 X 22 W12 X 14 W12 X 26 Previous...
Determine the required thickness of member BC and the diameter of the pins at A and B if the allowable normal stress for member BC sallow = 29ksi is and the allowable shear stress for the pins is tallow = 10 ksi.
A shaft is made of a steel alloy having an allowable shear stress of ?(allow) = 12 ?si. If the diameter of the shaft is 1.5 in., (a) determine the maximum torque T that can be transmitted. (b) What would be the maximum torque T’ if a 1-in.-diameter hole is bored through the shaft? (c) Sketch the shear-stress distribution along a radial line in each case. 2. A shaft is made of a steel alloy having an allowable shear stress...
The allowable bending stress is σ1ow-22 ksi and the allowable shear stress is Tallow 12 ksi. (Figure 1) Part A Select the lightest steel wide-flange beam from Appendix B that will safely support the loading shown. If there are several choicas of equal weight, choose the one with the shortest height. w14 × 26 W8 x 31 W10 × 39 w12 × 22 W12 × 26 W14 x 22 W10 × 30 W8 × 40 Submit Request Answer Figure 1...
1. Knowing that the allowable bending stress for the steel used is 24 ksi, select the most economical wide-flange beam to supoort the loading shown. (Hint: start by drawing the shear and moment diagrams). 2 kips/ft 12.5 kips 3 ft 3 ft
The A-36 W150x37.1 b that can be applied to the beam without causing the strut to buckle or the beam to exceed allowable shear stress. Take F.S. 2. (20 points) steel rod BC has a diameter of 50mm and is used as a strut to support the eam. Determine the maximum intensity w of the uniform distributed load sw 6 m 3 m
I can't figure this one out. The tension member is faster is fastened together using two bolts, one on each side of the member as shown. Each bolt has a diameter of 0.3 in. Determine the maximum load P that can be applied to the member if the allowable shear stress for the bolts is tau allow = 12 ksi and the allowable average normal stress id sigma allow = 20 ksi.
Required information The allowable shearing stress is 15 ksi in the steel rod AB and 8 ksi in the brass rod BC. A torque of magnitude T = 13 kip-in. is applied at A. T Steel Brass Determine the required diameter of rod AB. (Round the final answer to three decimal places.) The required diameter of rod AB is D in. Determine the required diameter of rod BC. (Round the final answer to three decimal places.) The required diameter of...
1.52 Solve Prob. 1.51, assuming that the structure has been redesigned to use 16-in.-diameter pins at A and C as well as at B and that no other changes have been made. A in. 8 in. B C 4 in. 6 in. Fig.P1.51 1.51 Link AC is made of a steel with a 65-ksi ultimate normal stress and has a 2-in. uniform rectangular cross section. It is connected to a support at A and to member BCD at C by-in.-diameter...
The allowable shear stress for the material is Tallow = 6 ksi. Pin A is subjected to double shear, whereas pin B is subjected to single shear. (Figure 1) Part A Determine the required diameter of the pins at A to the nearest 1/16 in. Express your answer as an exact decimal value and include appropriate units. da= Value Units Submit Request Answer Part B Determine the required diameter of the pin at B to the nearest 1/16 in. Express...