The cotter is used to hold the two rods together.(Figure 1) All parts are made of steel for which the failure normal st...
The cotter is used to hold the two rods together.(Figure 1) All
parts are made of steel for which the failure normal stress is
?fail=525 MPa and the failure shear stress is
?fail=325 MPa. Use a factor of safety of
(F.S.)t=2.90 in tension and(F.S.)s=1.70 in
shear.
Determine the smallest thickness t of the cotter.
Determine the smallest diameter d of the rods.
Homework Answers
Add Answer to:
The cotter is used to hold the two rods together.(Figure 1) All parts are made of steel for which the failure normal st...
Part A The cotter is used to hold the two rods together. (Figure 1) All parts...
Part A The cotter is used to hold the two rods together. (Figure 1) All parts are made of steel for which the failure normal stress is fail = 510 MPa and the failure shear stress is Trail = 365 MPa. Use a factor of safety of (F.S.)t = 2.30 in tension and (F.S.), = 1.71 in shear. Determine the smallest thickness t of the cotter. Express your answer to three significant figures and include appropriate units. de = Value...
Pls show work HW Set #1: Chapters 1 and 2 Problem 1.80 The cotter is used...
Pls
show work
HW Set #1: Chapters 1 and 2 Problem 1.80 The cotter is used to hold the two rods together. (Figure 1) All parts are made of steel for which the falure normal stress is Ơfall-480 MPa and the tadure shear stress is Thi 400 MPa Use a factor of safety of (F.S.),-2.30 in tension and (F.S.),-1.64 in shear Part A Determine the smallest thickness t of the cotter Express your answer to three significant figures and include...
Determine the smallest thickness t of the cotter Express your answer to three significant figures and...
Determine the smallest thickness t of the cotter Express your answer to three significant figures and include appropriate units The cotter is used to hold the two rods together (Figure 1) All parts are made of steel for which the failure normal stress is σ1il 520 MPa and the failure shear stress is Tail385 MPa. Use a factor of safey of (F.S.), 2.10 in tension and (F.S.) 1.71 in shear d,-Value Units Figure 1 of 1 SubmitR Request Answer 30...
The rods AB and CD are made of steel having a failure tensile stress of O...
The rods AB and CD are made of steel having a failure tensile stress of O fail = 510 MPa. Using a factor of safety of F.S. = 1.75 for tension, determine their smallest diameter so that they can support the load shown. The beam is assumed to be pin connected at A and C. В. D 6 kN 5 kN 4 kN A C 4 2 m ----2m- -3 m -3 m Figure: 07_PROB_076
4- The joint is fastened together using two bolts. Determine the required diameter of the bolts...
4- The joint is fastened together using two bolts. Determine the required diameter of the bolts if the failure shear stress for the bolts is fail = 350 MPa. Use a factor of safety for shear of F.S. = 2.5. 30 mm 80 KN 30 mm 40 KN 40 KN
For the shaft shown in figure 1, made of AISI steel 1030 CD with Sut =...
For the shaft shown in figure 1, made of AISI steel 1030 CD with Sut = 520 MPa and Sy = 440 MPa., determine the factor of safety based on failure theories for ductile of Maximum Shear Stress and Distortion Energy (Von Misses). The point selected for analysis is determined form the following table. The loads are F= 2.13 kN, P= 5.13 kN, and T = 31.3 N. m. 100 mm B 15-mm D. Р T
Question 2: (15 marks) Bracket ABC has loads applied as identified in Figure 2. A steel control r...
please label with detailed steps ! thank you
Question 2: (15 marks) Bracket ABC has loads applied as identified in Figure 2. A steel control rod A with ultimate normal stress of 600 MPa is attached to point B. At point C the steel pivot pin has an ultimate shearing stress of 350 MPa. Assuming a factor of safety of 3.3 determine: (i) The minimum acceptable diameter of the control rod AB (ii) The minimum acceptable diameter of the pivot...
Question A-36 steel pipe with an outer diameter of 100 mm and an inner diameter of...
Question A-36 steel pipe with an outer diameter of 100 mm and an inner diameter of 80 mm subjected to loadings shown in Figure 1. The pipe is rigidly fixed at B and P = 150 kN. Given the yield stress, Oy=250 MPa and factor of safety, F.S. = 1.5 is used against yielding on this entire pipe. (a) For the stress state at the surface, construct the Mohr circle and determine: (1) the total stresses at surface of the...
Question A-36 steel pipe with an outer diameter of 100 mm and an inner diameter of...
Question A-36 steel pipe with an outer diameter of 100 mm and an inner diameter of 80 mm subjected to loadings shown in Figure 1. The pipe is rigidly fixed at B and P - 150 kN. Given the yield stress, Oy -250 MPa and factor of safety, F.S. - 1.5 is used against yielding on this entire pipe. (a) For the stress state at the surface, construct the Mohr circle and determine: (1) the total stresses at surface of...
A countershaft, made of AISI 1035 CD steel, carrying two V-belt pulleys is shown in the figure. P...
A countershaft, made of AISI 1035 CD steel, carrying two V-belt pulleys is shown in the figure. Pulley A receives power from a motor through a belt with the belt tensions shown. The power is transmitted through the shaft and delivered to the belt on pulley B. Assume the belt tension on the loose side at B is 25 percent of the tension on the tight side (F2 - 0.25 F) 1) Based on the equations for yielding conditions discussed...
Part A The cotter is used to hold the two rods together. (Figure 1) All parts are made of steel for which the failure normal stress is fail = 510 MPa and the failure shear stress is Trail = 365 MPa. Use a factor of safety of (F.S.)t = 2.30 in tension and (F.S.), = 1.71 in shear. Determine the smallest thickness t of the cotter. Express your answer to three significant figures and include appropriate units. de = Value...
Pls
show work
HW Set #1: Chapters 1 and 2 Problem 1.80 The cotter is used to hold the two rods together. (Figure 1) All parts are made of steel for which the falure normal stress is Ơfall-480 MPa and the tadure shear stress is Thi 400 MPa Use a factor of safety of (F.S.),-2.30 in tension and (F.S.),-1.64 in shear Part A Determine the smallest thickness t of the cotter Express your answer to three significant figures and include...
Determine the smallest thickness t of the cotter Express your answer to three significant figures and include appropriate units The cotter is used to hold the two rods together (Figure 1) All parts are made of steel for which the failure normal stress is σ1il 520 MPa and the failure shear stress is Tail385 MPa. Use a factor of safey of (F.S.), 2.10 in tension and (F.S.) 1.71 in shear d,-Value Units Figure 1 of 1 SubmitR Request Answer 30...
The rods AB and CD are made of steel having a failure tensile stress of O fail = 510 MPa. Using a factor of safety of F.S. = 1.75 for tension, determine their smallest diameter so that they can support the load shown. The beam is assumed to be pin connected at A and C. В. D 6 kN 5 kN 4 kN A C 4 2 m ----2m- -3 m -3 m Figure: 07_PROB_076
4- The joint is fastened together using two bolts. Determine the required diameter of the bolts if the failure shear stress for the bolts is fail = 350 MPa. Use a factor of safety for shear of F.S. = 2.5. 30 mm 80 KN 30 mm 40 KN 40 KN
For the shaft shown in figure 1, made of AISI steel 1030 CD with Sut = 520 MPa and Sy = 440 MPa., determine the factor of safety based on failure theories for ductile of Maximum Shear Stress and Distortion Energy (Von Misses). The point selected for analysis is determined form the following table. The loads are F= 2.13 kN, P= 5.13 kN, and T = 31.3 N. m. 100 mm B 15-mm D. Р T
please label with detailed steps ! thank you
Question 2: (15 marks) Bracket ABC has loads applied as identified in Figure 2. A steel control rod A with ultimate normal stress of 600 MPa is attached to point B. At point C the steel pivot pin has an ultimate shearing stress of 350 MPa. Assuming a factor of safety of 3.3 determine: (i) The minimum acceptable diameter of the control rod AB (ii) The minimum acceptable diameter of the pivot...
Question A-36 steel pipe with an outer diameter of 100 mm and an inner diameter of 80 mm subjected to loadings shown in Figure 1. The pipe is rigidly fixed at B and P = 150 kN. Given the yield stress, Oy=250 MPa and factor of safety, F.S. = 1.5 is used against yielding on this entire pipe. (a) For the stress state at the surface, construct the Mohr circle and determine: (1) the total stresses at surface of the...
Question A-36 steel pipe with an outer diameter of 100 mm and an inner diameter of 80 mm subjected to loadings shown in Figure 1. The pipe is rigidly fixed at B and P - 150 kN. Given the yield stress, Oy -250 MPa and factor of safety, F.S. - 1.5 is used against yielding on this entire pipe. (a) For the stress state at the surface, construct the Mohr circle and determine: (1) the total stresses at surface of...
A countershaft, made of AISI 1035 CD steel, carrying two V-belt pulleys is shown in the figure. Pulley A receives power from a motor through a belt with the belt tensions shown. The power is transmitted through the shaft and delivered to the belt on pulley B. Assume the belt tension on the loose side at B is 25 percent of the tension on the tight side (F2 - 0.25 F) 1) Based on the equations for yielding conditions discussed...
Most questions answered within 3 hours.
-
At the start of a CD it is spinning at a rate of 525 rpm
(revolutions...
asked 33 minutes ago -
4. Without doing any calculations, predict whether the observed
∆T would increase, decrease or remain the...
asked 1 hour ago -
Based on the range, which of the following sets of scores has
the greatest variability? 3,...
asked 2 hours ago -
Ripples in a pond travel at a velocity of 3 m/s with one peak
passing a...
asked 2 hours ago -
A man stands on the roof of a building of height 13.0 mm and
throws a...
asked 2 hours ago -
The extent to which assets are financed by borrowed funds and
other liabilities is indicated by:...
asked 3 hours ago -
Explain in detail
Germany is the fifth largest economy
explain what goods and services Germany specializes...
asked 4 hours ago -
The density of platinum is 21.45 g/mL. If a cube of platinum
with a mass of...
asked 4 hours ago -
Accounts Receivable
Sales
A/R Posting
Extended Sales Invoice
Packing Slip
Compare invoice to packing slip 2...
asked 4 hours ago -
Michaella, age 23, is a full-time law student and is claimed by
her parents as a...
asked 4 hours ago -
Why are polymers not typically casted into products?
asked 4 hours ago -
When rolling a die 129 times, what is the probability of rolling
a 6 no more...
asked 4 hours ago