Please solve by using MATLAB, show all the steps
Problem 2
An object propelled directly upward with an initial velocity of 50
m/s has a velocity given by
v= - 9.8t + 50
In this case, the positive direction of velocity is upward.
a) Plot a curve of the velocity as a function of time from t=0 to
t=8 s.
b) Keep the default horizontal and vertical scales.
c) Provide labeling for the two axes and provide a title.
d) Use Insert Line function within Figure Window to add abscissa
across the the graph corresponding
to velocity of zero.
e) Add a grid.
__________________________________________________________________________________
clc;clear all;close all;
t=0:0.01:8;%time range
v=-9.8*t+50;%velocity time fuction
plot(t,v,'b')
xlabel('time in sec')
ylabel('velocity in m/sec')
title('velocity Vs time')
t1=50/9.8;%to find when the velocity become zero
line([0,t1],[0,0],'color','r')
grid on
Please solve by using MATLAB, show all the steps Problem 2 An object propelled directly upward...
General Guidelines MATLAB Symbolic Computations are NOT allowed for this assignment. Generate ALL plots using MATLAB. Include your MATLAB codes as an appendix at the end of your document. All plots should be clearly labeled: provide a X-axes and y-axes labels, specify units as needed, add titles and legend as needed, add grids as needed, use different line stiles and/or symbols as needed. 6) Consider the CT signal X(t) = u(t)- r(t) +r(t-1), where r(t) = t.u(t). a) Derive the...
These questions are to be answered using MATLAB. I only need #3 answered, but #1 provides information (like initial velocity, etc.) required for the questions. I think I have it done, but I'd like to see if there are other ways to use MATLAB for this question. PROJECTILES The distance a projectile travels when fired at an angle 8 is a function of time and can be divided into horizontal and vertical distances. Horizontal (1) = 1.V.cos(0) Vertical(t) = 1•...
solve all questions simply by using matlab. write all step here please 1Normal 1 No Spac Heading1 Heading 2 DISCUSSION Solve all tasks given below: 1. Consider function f(x) 3.5-0.5x cos(6x) for the value of x between -2.0 until 4.0. Draw the plot in dash line and in red colour, Label the title and all axes. 2. Consider the following functions for 0sxS pi: x() 10e0.St sin(3t +2) y(t) 7e-04t cos(5t - 3) (a) Draw both graphs on the same...
USING MATLAB Please post code 1. Solve the 2nd order differential equation ?+89 +15y-sin(t), y(0)-1,?(0)-2 symbolically and numerically, and plot both results together over the time interval 0,10 sec. Provide appropriate labels on both axes, a title, and a legend that denotes each solution. Check your symbolic answer by using the Matlab DIFF function to compute the appropriate derivatives and then substituting them into the differential equation.
*** SOLVE USING MATLAB *** Problem 2 A ball thrown up falls back to the floor and bounces many times. For a ball thrown up in the direction shown in the figure, position of the ball as a function of time is given by: the The velocities in the x and y directions are constants throughout the motion and are given byo sin ()cosa) and ysin ()sin(a). In the vertical z direc- tion the initial velocity is v, = cos(9),...
Please help me solve the bottom two question using Matlab and show the steps to do it. Thanks. i appreciate your help (12 points each) 10. In dynamics course, a particle move in the elliptical slots due to the motion of the slotted link as shown on the figure. The normal acceleration of the particle is proportional to the velocity square over the radius of curvature (r). + y2 = 1000 _(1 + (x) 325 r(x) = — a) Calculated...
Please solve these using matlab Problem 1 Given the transfer functions e S +5 (a) C(s) 20 S + 20 (b) Use the step function to determine the time constant and rise time for each system. Note: estimate these values from the plot and do not use the stepinfo function. Problem 2 Given the transfer function 100 G(S) = 22 +45 + 25 a. Use the plot resulting from the step function in MATLAB to determine the percent overshoot, settling...
2. Instead of using the "cook book" procedure, repeat #1 using 'rltoor in Matlab. The input to 'tltool is the open-loop transfer function. Add the following specifications before adding your compensator: · ζ20.8 26 To add specifications, right click on the root locus and select "Design Requirements", then "New". You may also need to adjust the axes on the figure before adding your compensator. Right click on the figure somewhere in the non-shaded area, then select "Properties", then the "Limits"...
solve all questions simply by using Matlab writh all steps here please 1 Normal 1 No Spac.. Heading 1 Heading2 Title Subtitle Subtle Em... Ep Paragraph Styles 7. Write an M-file that creates subplots (not superimposed) of Yfor n[:5) and X= [-10 : 0.01 : 101. Each subplot's Y axis should have an appropriate title. 8. Write a Matlab program to calculate the values of the function ro-ssint for all t where sint >0 f(t)=t0 elsewhere. 6π at intervals of...
Please help me with this MATLAB programming problem! Im coding iin MATLAB2018 if that makes any difference! The first picture is the question i need to answer. The picture below is used as reference to answer the question. The last picture (below) is the into to the problem, and is used as reference. 1. Use Matlab to create the following single plot with three subplots. All titles, gridlines, and axis labels should be as shown. Arc System Response 15 E...