solve P11 and P12 based on Part 3 Mechanical Springs A helcal compression spring is made...
This is the clearest I can provide, please solve it don't ask for clearer picture If this component has a nominal aternating tress ,#7Asi and a mid range stress a 8 ksi with a endurance limit S15.0ki, find the safety factor against infinite ife using the Goodman criteria Problem 8 fatigue stress concentration factor A 3that affects both stress components and a fully corrected 09 0) 3.1 A) 1.3 B)1.1 924 Part 3 Mechanical Springs A helical compression spring is...
2. A helical compression spring is made from No. 8 steel wire and is to carry a 100 lb static load at a deflection of 1 inch. The outside coil diameter of the spring is 0.972 inches. The spring ends are squared. Assume the torsional yield strength of the wire is 80000 psi, and the shear modulus is 11.4 Mpsi, determine (a) The static load corresponding to the yield strength. (b) The deflection that would be caused by the load...
8. A helical compression spring is made of HD (A227) and has a spring constant of 4.25 lbs per inch. If the wire diameter is 0.1 inch and the coil mean diameter is 1.5 inch, what is the number of active coils: b) 9 a) 8 c) 10 d) 11 e) None of these 8. A helical compression spring is made of HD (A227) and has a spring constant of 4.25 lbs per inch. If the wire diameter is 0.1...
2. A helical compression spring is to be designed as shown in Fig Q2. The spring is required to exert a force of Po-102 N when compressed to a length of lo=44 mm. When its length is 1=76 mm, it must exert a force of P=22 N. The spring will be cycled rapidly, with severe service required. Use ASTM A401 steel wire. The factor of safety, η, need to be larger than 1.5. Starting with a spring index of 9,...
Problem: A helical compression spring is made with music wire with wire diameter of 5 mm, mean coil diameter of 51 mm, a total of 12 coils, a free length of 127 mm, with squared ends. (a) Find the solid length. (b) Find the force necessary to deflect the spring to its solid length.
Machine Desgin course related Machine Design related, shigley's mechanical engineering 4. A compression spring is needed to fit over a 12mm diameter rod. To allow for some clearance, the inside diameter of the spring is to be 15mm. To ensure a reasonable coil, use a spring index of 8. The spring is to be used in a machine by compressing it from a free length of 125mm through a stroke of 75 mm to its solid length. The spring should...
Q.3 Three identical compression springs were used to support a platform ( weight| = 300 lbs) shown in figure below. Spring properties are: ASTM A 227 steel wire, hard drawn ( Fig 19-8), G=11.5*10°, E = 28.6*10°, total number of coils are 7, both ends are squared and ground, wire diameter = 0.15 in, outside diameter = 1.5 inches, free length = 4 inches. All ends of all springs are fixed. Find stability of this system. (7) %3D %3D %3D...
1- A helical compression spring is to be made of oil-tempered wire of 4-mm diameter with a spring index of C = 10. The spring is to operate inside a hole, so buckling is not a problem and the ends can be left plain. The free length of the spring should be 80 mm. A force of 50 N should deflect the spring 15 mm. (a) Determine the spring rate. (b) Determine the minimum hole diameter for the spring to...
1- A helical compression spring is to be made of oil-tempered wire of 4-mm diameter with a spring index of C = 10. The spring is to operate inside a hole, so buckling is not a problem and the ends can be left plain. The free length of the spring should be 80 mm. A force of 50 N should deflect the spring 15 mm. (a) Determine the spring rate. (b) Determine the minimum hole diameter for the spring to...
1- A helical compression spring is to be made of oil-tempered wire of 4-mm diameter with a spring index of C = 10. The spring is to operate inside a hole, so buckling is not a problem and the ends can be left plain. The free length of the spring should be 80 mm. A force of 50 N should deflect the spring 15 mm. (a) Determine the spring rate. (b) Determine the minimum hole diameter for the spring to...