Given a +30 mA current limit for a function generator, what is the largest voltage you...
Given a ±30 mA current limit for a function generator, what is the smallest resistor you can put across the function generator and still get a士3V signal?
Given a 30mA current limit for a function generator, what is the smallest resistor you can put across the function generator and still get a 3V signal?
A resistor and capacitor are connected in series across an ac generator. The voltage of the generator is given by V() = Vocos(wt), where Vo = 120V,w = 120x rad/s, R = 55082, and C = 7.54F. (a) What is the magnitude of the impedance of the RC circuit? (b) What is the amplitude of the current through the resistor? (e) What is the phase difference between the voltage and current? The magnitude of the impedance is The amplitude of...
A resistor and capacitor are connected in series across an ac generator. The voltage of the generator is given by V(0) = Vocos(wt), where VO = 120V, w = 120+ rad/s, R=55092, and C = 3pF. (a) What is the magnitude of the impedance of the RC circuit (b) What is the amplitude of the current through the resistor? (c) What is the phase difference between the voltage and current? The magnitude of the impedance is 1041.3 22. The amplitude...
4. The MOSFET in the circuit given below has Vi- 1 V, kn 0.8 mA/V2, and VA 40 V a) Find the values of Rs, Ro, and Ro so that Io -0.1 mA, the largest possible value for RD is used while a maximum signal swing at the drain of tl V is possible, and the input resistance at the gate is 10 MS2. b) Find the values of gm and ro at the bias point c) If terminal Z...
An ac generator has a frequency of 5.5 kHz and a voltage of 30 V. When an inductor is connected between the terminals of this generator, the current in the inductor is 30 mA. What is the inductance of the inductor? L= ?
Design a 7.5-V zener regulator circuit using a 7.5-V zener specified at 10 mA. The zener has an incremental resistance r, = 30 Q and a knee current of 0.5 mA. The regulator operates from a 10-V supply and delivers a nominal current of 5 mA to the load. What is the value of R you have chosen? What is the regulator output voltage when the supply is 10% high? Is 10% low? What is the output voltage when both...
Design a 7.5-V zener regulator circuit using a 7.5-V zener specified at 10 mA. The zener has an incremental resistance rz = 30 Ω and a knee current of 0.5 mA. The regulator operates from a 10-V supply and delivers a nominal current of 5 mA to the load. What is the value of R you have chosen? What is the regulator output voltage when the supply is 10% high? Is 10% low? What is the output voltage when both...
Use NI Multisim 3) (+3) Do the following in Multisim and verify the results with calculations (see equations 1.7-1.9). Use the function generator to create the 120 Vrms signal as you would see in the classroom wall outlet. Connect it to a resistor (the value of the resistor is your choice, but must have two decimal places) and measure the RMS voltage across the resistor and current through the resistor with separate Multimeters. Calculate the RMS voltage and current and...
D 6.112 The MOSFET in the circuit of Fig. P6.112 has = 5 mA/V, and V, = 40 V. (a) Find the values of Rs,RD, and RG so that ID=0.4 mA, the largest possible value for R is used while a maximum signal swing at the drain of +0.8 V is possible, and the input resistance at the gate is 10 MS2. Neglect the Early effect. (b) Find the values of gm and r, at the bias point. (c) If...