The average power used by a stereo speaker is 55 W. Assuming that the speaker can be treated as a 5.5-Ω resistance, find the peak value of the ac voltage applied to the speaker.
The average power used by a stereo speaker is 55 W. Assuming that the speaker can...
76. *A stereo speaker has a resistance of 8 Ω. If the power output is 40 W, calculate the current passing through the speaker wires.
9.5 (5) A couple moved to Europe and found that the house they rented consumed power on average as indicated below (a) Find the time averaged and peak line currents laA, IbB and InN. (ignore the line drop (b) Calculate the time averaged and peak voltage drop on the neutral wire ( 0.05 Ω (c) Calculate the total power bill for a four week period at a rate of $0.12 /kWh. (include the voltage in these calculations) resistance) due to...
A voltmeter and an ammeter are used to respectively monitor the voltage across and the current through a resistor connected to an AC source. If the resistor has a value of 14.0 Ω and the ammeter reads 8.04 A, determine the following. (a) the rms voltage (in V) across the resistor V (b) the peak voltage (in V) of the source V (c) the maximum current (in A) in the resistor A (d) the average power (in W) delivered to...
It is required to design a class B output stage to deliver an average power of 20 W to an 8-Ω load. The power supply is to be selected such that Vcc is about 5 V greater than the peak output voltage. This avoids transistor saturation and the associated nonlinear distortion, and allows for including short-circuit protection circuitry. (The latter will be discussed in Section 12.6.) Determine the supply voltage required the peak current drawn from each supply, the total...
A capacitor used to provide steady voltages in the power supply of a stereo amplifier charges rapidly to 35 V every 1/60 second. It must then hold that voltage to within 1.0 V for the next 1/60 s while it discharges through the amplifier circuit. If the circuit draws 1.2 A from the 35-V supply, what is its effective resistance (in ohms)? What value of capacitance is needed (in mF)?
Power in an AC Circuit 1 2 3 4 5 6 A circuit is constructed with an AC generator, a resistor, capacitor and inductor as shown. The generator voltage varies in time as ε =Va - Vb = εmsinωt, where εm = 120 V and ω = 314 radians/second. The inductance L = 283 mH. The values for the capacitance C and the resistance R are unkown. What is known is that the current in the circuit leads the voltage...
11.10 The circuit shown in Fig. P11.10 uses a 12-V ac source to deliver power to an 8-Ω speaker. If the average power delivered to the speaker is 1.8 W at an audio frequency f= 1 kHz, what is the value of the coupling coefficient k? 4Ω 12 cos 2z/t (V) 3mH 12 mH 8Ω Figure P11.10: Circuit for Problem 11.10.
What is the resistance of a lightbulb that uses an average power of 70.0 W when connected to a 60.0 Hz power source having a maximum voltage of 150 V? ohm (b) what is the resistance of a 90 w bulb? ohm
A 80 Ω resistor is rated at 1.00 W maximum power capacity. There is a maximum voltage that can be applied across the resistor without exceeding its maximum power rating. 1) What is this voltage? 2) What is the current at this voltage?
A voltmeter and an ammeter are used to respectively monitor the voltage across and the current through a resistor connected to an AC source. If the resistor has a value of 13.00 and the ammeter reads 7.08 A, determine the following (a) the rms voltage (in V) across the resistor v (b) the peak voltage (in V) of the source V (c) the maximum current in A) in the resistor A (d) the average power in W) delivered to the...