Design a sequential circuit whose output Z becomes 1 when the pattern "01101" is found at 1-bit input X under the following conditions.
(1) Use a D flip-flop for the flip-flop used as a Mealy machine
(2) Use a RS flip-flop for the flip-flop used as a Moore machine
Design a sequential circuit whose output Z becomes 1 when the pattern "01101" is found at 1-bit input X under the following conditions. (1) Use a D flip-flop for the flip-flop used as a Mealy...
x is a successive circuit with 1 input and one z output flip flop input and output equations are as follows. a) Draw the block diagram of the circuit. b) Explain whether the circuit is a Mealy or Moore circuit. c) Analyze the behavior of the circuit A(t+1)=A’B’X B(t+1)= A+C’X’+BCX C(t+1)= AX+CX’+A’B’X’ Y= A’X
Design a Mealy sequential circuit with one input X and one output Y that recognizes the sequence 1101 anywhere on the input sequence X. When the circuit recognizes the sequence it asserts its output Z high. Design the circuit with T flip flops.
digital logic Design a sequential circuit for a single-input and single output Moore-type FSM that produces an output of 1 if in the input sequence it detects either 110 patterns. Overlapping sequences should be detected.(Note : use D flip-flops in your design. Repeat problem 2 for a Mealy-type FSM 2. 3. Design a sequential circuit for a single-input and single output Moore-type FSM that produces an output of 1 if in the input sequence it detects either 110 patterns. Overlapping...
1. A sequential circuit has one JK flip-flop A, one input x, and one output y. The flip-flop input equation and circuit output equation are: (a) Draw the logic diagram of the circuit (b) Tabulate the state table of the circuit (P. S., Input, N. S., Output). (c) Draw the state diagram. (d) Derive the state equation A(t+ 1). (e) Starting from state A 0 in the state diagram, determine the state transitions and output sequence that will be generated...
A sequential circuit with two D Flip-Flops and one input X and one output Y is specifed by the following input equations: Y = A'+B DA = X + B DB = XA' (a) Draw the logic diagram of the circuit (b) Derive the state table. (c) Derive the state diagram. (b) Is this a Mealy or a Moore machine?
task 1: In digital electronics and modern computer hardware, a flip-flop is sequential digital circuit used as a basic memory element. It has two stable states and can be used to store state information. One of its states represents '1' while the other represents '0'. The most common types of flip-flops are SR-flip-flop, JK-flip-flop, and D flip-flop. When used in a finite-state machine, the output and next state depend not only on its current input, but also on its current...
Write a Verilog program to describe a sequential circuit that has input X and output Z. Z goes to 1 whenever the last four X inputs (in four clock cycles) are 1001 or 0110. Use a switch (SW1) on the DE1 board for X and a red LED for Z. Use a push button as the clock input. Use both the Moore and Mealy models to describe the circuit.
1. Given the state diagram shown below for a two-state synchronous sequential Mealy circuit with input. and output z, realize the circuit using D flip-flops. Your answer must include the state transition,excita- tion, and output tables, the excitation equation(s), and a labeled circuit diagram 1/0 2. Given the state diagram in Problem 1, realize the circuit using JK flip-flops. Your answer must include the state transition, excitation, and output tables, the excitation equation(s), and a labeled circuit diagram. 3. Given...
A sequential circuit has two D flip-flops, A and B, one input x and one output y. The flip-flop input functions and the output function are the folllowing: DA = Ax` + Bx DB= A`x + Bx` y = Ax + Bx a) Write the state table of the circuit b) Draw the state diagram of the circuit (note that the output changes when the input changes)
Implement the following bit sequential Adder-Subtractor design. X and Y are two operand inputs and Z is for the control signal i.e. Z is the selection bit. When Z has value 0, the circuit is an adder, meanwhile, the D flip-flop should be initialized to 0 for each addition. When Z has value 1, it performs subtraction, meanwhile, the D flip-flop should be initialized to 1 for each subtraction. Test your Adder-Subtractor circuit on the following operations and use the...