x is a successive circuit with 1 input and one z output
flip flop input and output equations are as follows.
a) Draw the block diagram of the circuit.
b) Explain whether the circuit is a Mealy or Moore circuit.
c) Analyze the behavior of the circuit
A(t+1)=A’B’X
B(t+1)= A+C’X’+BCX
C(t+1)= AX+CX’+A’B’X’
Y= A’X
x is a successive circuit with 1 input and one z output flip flop input and...
Design a sequential circuit whose output Z becomes 1 when the pattern "01101" is found at 1-bit input X under the following conditions. (1) Use a D flip-flop for the flip-flop used as a Mealy machine (2) Use a RS flip-flop for the flip-flop used as a Moore machine
1. A sequential circuit has one JK flip-flop A, one input x, and one output y. The flip-flop input equation and circuit output equation are: (a) Draw the logic diagram of the circuit (b) Tabulate the state table of the circuit (P. S., Input, N. S., Output). (c) Draw the state diagram. (d) Derive the state equation A(t+ 1). (e) Starting from state A 0 in the state diagram, determine the state transitions and output sequence that will be generated...
A sequential circuit with two D Flip-Flops and one input X and one output Y is specifed by the following input equations: Y = A'+B DA = X + B DB = XA' (a) Draw the logic diagram of the circuit (b) Derive the state table. (c) Derive the state diagram. (b) Is this a Mealy or a Moore machine?
A sequential circuit has two D flip-flops, A and B, one input x and one output y. The flip-flop input functions and the output function are the folllowing: DA = Ax` + Bx DB= A`x + Bx` y = Ax + Bx a) Write the state table of the circuit b) Draw the state diagram of the circuit (note that the output changes when the input changes)
A sequential circuit with two flip flops, A and B; one input, x; and one output y, is specified by the following next-state and output equations: B(t+1) = AX A(t+1) = A’B + BX’ + AB’X y = A’X’ + B’ a) List the circuit state table and draw the corresponding state diagram b) Draw the logic diagram of the circuit using only, one D-type and one T-type flip flops, one 2X4 decoder and one 2-input OR gate. The complement of the input...
A sequential circuit with two flip flops, A and B; one input, x; and one output y, is specified by the following next-state and output equations. B(t+1)=Ax A(t+1)=A'B+Bx'+AB'x a) List the circuit state table and draw the corresponding state diagram. b) Draw the logic diagram of the circuit using only, one D-type and one T-type flip flops, one 2X4 decoder and one 2-input OR gate. The complement of the input variable, x is not available.
A sequential circuit has one flip-flop Q, two inputs x and y, and one output. It consists of a full-adder circuit connected to a D flip-flop, as shown in Figure 1 as follows. For the sequential circuit derive (or draw) the,A) state equation B) state table C) state diagram
Draw the gate level circuit schematic of a D flip-flop and a T flip-flop based on the cross-coupled NAND latch. Briefly discuss the timing behavior of a D flip-flop, a T flip-flop and a latch. (a) (8 Marks) circuit has three inputs, S, C and C2. S is the control input. When S-O, the circuit behaves like a D flip-flop, and when S-1, the circuit behaves like a T flip-flop. The input characteristics of the circuit are tabulated in Table...
8. A sequenti by the following input function: al circuit has one flip-flop and two inputs X and Y, and one output S. The circuit is described Dt = X xor Y xor S With D as the input to the D flop flop. (a) Draw the logic diagram of the circuit (b) Derive the state table (c) Derive the state diagram