1. The following two-loop circuit has a constant current source, I, across which an unknown potential...
Consider the circuit pictured. a. Write down the ’loop rule’ for the top and bottom loops of this circuit assuming you go around the loops clockwise. b. Write down the ’junction rule’ for the two junctions in the circuit. c. Determine the current and potential difference across each resistor for the following values: R1 = 1.00 ?, R2 = 2.00 ?, R3 = 3.00 ?, r1 = 1.00 × 10?1 ?, r2 = 1.00 × 10?1 ?, E1 = 1.00...
1) In the circuit below the currents are named A, and lc The current direction is determined by the source (out of positive terminal) in the middle and right branches and is clockwise in the left branch · IA flows through R2 and R1 Is flows through R4 and Vb cflows through R3, Vc AB R2 R3 R4 R1 Vb a) Draw the circuit and show the 3 currents described above, including arrows showing the current direction. Show the voltage...
A. Write Kirchhoff's loop rule (clockwise) for the circuit shown in (Figure 1). B. Determine the current in the circuit for the case in which ε1 = 20.0 V, ε2 = 8.0 V, R1 = 30.0 Ω, R2 = 20.0 Ω, and R3 = 10.0 Ω. C. Using this value of current, start at position A and move clockwise around the circuit, calculating the electric potential change across each element in the circuit (be sure to indicate the sign of...
3. Not all resistor networks can be easily simplified using the formulas for resistances in series and parallel. The following circuit, which has five resistors in a "bridge" configuration, is one such circuit R2 Nevertheless, it can still be analyzed as a three-loop circuit from which the current flowing through the voltage source can be calculated (a) Write down the 3x3 matrix equation which can be solved to determine the vector of currents in the three loops (b) Using Kramer's...
(written portion due 5/7/2019) Inductor and a Resistor in parallel A circuit with two resistors has one junction in it. The split has a resistor on one side and an inductor on the other a) Show a sketch of what the current in the inductor as a function of time and propose an equation that fits the plot. The solution should have a signature time in it. b) Using the junction rule, plot a sketch of what the current in...
Find the current flowing through the circuit of the figure, assuming you have a 12.60V source, and the resistance values are R1 = 1.60kΩ, R2 = 12.00kΩ, R3 = 4.40kΩ and R4 = 108.00kΩ. Express your answer in mA. .V R1 R2 R3 R4 2 w Liw
1. a. What is the resistance of the circuit? (Ω/OHM) b. What is the magnitude of the potential across resistor R3? (V) c. What is the magnitude of the current in resistor R3? (A) d. What is the magnitude of the potential across resistor R1? (V) e. What is the magnitude of the potential across resistor R2? (V) f. What is the magnitude of the current through resistor R1? (A) g. What is the magnitude of the current through resistor...
A. Draw the complex circuit described below A 12 volt emf source connected in series with R1 (3Ω) , in series R1 there are R2 (2Ω) and lamp 1 (4Ω) which are in parallel with each other. Connected in series with that parallel loop is another parallel loop, which includes on one branch , R3 (5Ω), R4 (2Ω) and Lamp 2 (3Ω) in series, and on the other branch of this parallel loop is R5 (7Ω), After that parallel branch...
1) 2) 3) Using Ohm's Law, the answer for 2 is: (don't need an answer for number 3) 4) R1 V. + R2 12 R3 https://drive.google.com/file/d/1WJUWDo8q7wGCQmwBgMvR04B_SY-MNJNN/view?usp=sharing Consider the circuit in Figure 2. We will assume that both the power supply's potentials V and V, along with the resistors R, through R3 are known quantities where the currents flowing through the circuit are unknown. Since there are three unknown currents in this circuit, three linearly independent equations are needed in order...
a. Use source transformations to reduce the circuit to a single loop with one V supply and one resistor in series with the unknown component X. b. Use source transformations to reduce the circuit to a single node pair circuit with one I supply in parallel with one resistor and the unknown component X. c. Use your answer to part a to determine the voltage drop across component X if it is an open. d. Use your answer to part...