The coefficient of friction is dimensionless and it does not have any unit. It is a constant that depends upon materials.
ere your results within range? 2. What are the units for the coefficient of friction? (Hint:...
In Figure 2, a block of weight W=100 N is sliding down a 2-stage ramp defined by the angles a = 30° and B = 45°. The distances OA and OB are 2 m and 4 m respectively. The friction coefficient for the entire ramp is u=0.3. B Figure 2: System for Question 5. (a) Derive an expression for the component of the block's weight acting parallel to the 2-stage ramp (Hint: since the ramp has 2 stages defined by...
What is the coefficient of static friction given this graph
and data table?
The margin of error is 0.01. ( Hint: Start with finding the
final experimental gradient and divide it by gravity.)
Chart 1: Data for the smooth surface Coefficient of Static Friction - Smooth Surface 1 Fsmax Trendline for Fsmax Steepest Slope Trendline for Steepest Slope 0.75 Shallowest Trendline for Shallowest 0.5 0.25 0 100 150 200 250 300 350 Chart 2: Data for the rough surface 2...
x-μ 6. Hint: use the formula*. If X falls within a range, transform both lower and upper limits. Let X be normally distributed with mean deviation σ 4 a. Find P(X30). b. Find P(X> 2), c. Find P(4 <X< 10). d. Find P(6 <X< 14) 10 and standard
the coefficient of static friction between block A and its
incline is 0.27. What must the minimum coefficient of static
friction between block B and its incline be if the blocks are in
equilibrium? The mass of block B is twice that of block A. If the
coefficient of friction is less than its minimum, in which
direction will the blocks slide?
assume angle a = 35 degrees and angle b = 35 degrees
RCES Exercise 7.1.07 Your answer is...
What is the friction coefficient for a Reynolds number of 1600 and dimensionless roughness of 0.0242? Keep four decimal places in your answer. What is the friction coefficient for a Reynolds number of 200000 and dimensionless roughness of 0.0196? Keep four decimal places in your answer. A 3.1 cm diameter, 10 meters long pipe has 2 90° regular, threaded elbows, 4 45° long-radius, flanged elbows, 9 unions, 1 ball valve(s), fully open and 1 gate valve(s) half open. Water flows...
Also find the friction coefficient which is consistent with
the data given. Please show all your steps and equations used in
the solution
The box of negligible size is sliding down along a curved path defined by th A(A increase in speed is dv/dt = 4 m magnitude of the acceleration of the box at this instant. e parabola y 0.4x2. When it is at 1.6 m), the speed is v 8 m/s and the 2 m, yA 2 /s?....
A block of mass m = 3.5 kg is
on an inclined plane with a coefficient of friction
μ1 = 0.31, at an
initial height h = 0.53 m above
the ground. The plane is inclined at an angle θ =
54°. The block is then compressed against
a spring a distance Δx = 0.11 m
from its equilibrium point (the spring has a spring constant of
k1 = 39 N/m) and
released. At the bottom of the inclined plane...
1750 kg tow truck comes to take your 950kg car away if the coefficient of friction is 0.420 what force must the truck's engine apply in order to accelerate away at 2.20 m/s^2
2*. A person wants to push a lamp (mass 8.0 kg) across the floor. The coefficient of friction be tween the lamp and the floor is k = 0.15. Cal- culate the maximum height x above the floor at which the person can push the lamp so that the lamp slides at constant speed rather than tips. The base of the lamp is a circle of radius 0.12 m. The lamp's center of gravity is directly above the center of...
2. If your coefficient (1) were 0.45 and the Normal Force were 400 N, what would be the Friction force?