Review A water filled pipe has water flowing at v1= 6.20 m/s in a section of...
Review A water filled pipe has water flowing at v1= 6.20 m/s in a section of pipe where the diameter is d1= 19.2 cm and the pressure is known to be P1= 7.00×104 N/m2 above atmospheric pressure.
1- If the pipe carries the water 3.5 meters up hill without any change in diameter, what is the new absolute pressure within the pipe?
2- After flowing up the hill described above, the pipe narrows to 80% of its original radius, what will be the new water velocity (
3- What will be the absolute pressure (P3) in the smaller pipe?
4- What is the volume flow rate through the smaller pipe? Give your answer in m3/sec.
Homework Answers
Add Answer to:
Review A water filled pipe has water flowing at v1= 6.20 m/s in
a section of...
A horizontal pipe contains water at a pressure of 130kPa flowing with a speed of 1.5m/s...
A horizontal pipe contains water at a pressure of 130kPa flowing with a speed of 1.5m/s . The pipe narrows to one-half its original diameter. A) What is the speed of the water? (in m/s) B) What is the pressure of the water? (in kPa) Thanks!
Water is flowing through a horizontal pipe with diameter, D1, at a velocity, V1, and under a pres...
Water is flowing through a horizontal pipe with diameter, D1, at
a velocity, V1, and under a pressure, P1. It enters a 900 reducing
bend (Shown in grey in Fig 2) that connects to a vertical pipe of
diameter, D2. The inlet of the bend is 50 cm above the exit of the
bend (as shown in Fig 2). Axes for positive directions of x and z
coordinates are provided. Figure 2 Side view of reducing bend from
horizontal to...
Water is flowing through a horizontal pipe with an inside diameter of 8.00cm. The pipe narrows...
Water is flowing through a horizontal pipe with an inside diameter of 8.00cm. The pipe narrows to an inside diameter of 3.75cm. Assume the water is an ideal incompressible fluid. What is the velocity of the fluid initially, v_1 (when It is flowing in the 8.00cm diameter section) if the velocity of the water in the narrow part of the pipe is measured at V_2 = 27m/s? If the initial pressure is known to be 670 kPa what is the...
Water flows at speed of 6 m/s through a horizontal pipe of diameter 3.5 cm. The...
Water flows at speed of 6 m/s through a horizontal pipe of
diameter 3.5 cm. The gauge pressure P1 of the water in the pipe is
1.7 atm. A short segment of the pipe is constricted to a smaller
diameter of 2.4 cm .
What is the gauge pressure of the water flowing through the
constricted segment? Atmospheric pressure is 1.013 × 10^5 Pa. The
density of water is 1000 kg/m^3 . The viscosity of water is
negligible. Answer in...
Water moves through a pipe at 6 m/s under an absolute pressure of 330 kPa. The...
Water moves through a pipe at 6
m/s under an absolute pressure of 330 kPa. The pipe narrows to one
half of its original diameter. What is the absolute pressure in the
narrow part of the pipe?
Water moves through a pipe at 6 m/s under an absolute pressure of 330 kPa. The pipe narrows to one half of its original diameter. What is the absolute pressure in the narrow part of the pipe? Pressure = Number Pascals
Water is flowing through a 10-cm-diameter water pipe at a rate of 0.1 m/s. Then, a...
Water is flowing through a 10-cm-diameter water pipe at a rate of 0.1 m/s. Then, a diffuser with an outlet diameter of 20 cm is bolted to the pipe in order to slow down water as it exits the diffuser to atmospheric pressure, as shown in the given figure. Disregarding frictional effects, determine the force exerted on the bolts due to the water flow. Take the density of water to be 1000 kg/m3 -t- d 10 cmm D = 20...
A horizontal pipe contains water at a pressure of 120 kPa flowing with a speed of...
A horizontal pipe contains water at a pressure of 120 kPa flowing with a speed of 1.9 m/s. When the pipe narrows to one-half its original diameter, what are (a) the speed and (b) the pressure of the water?
1. Water is flowing in a pipe as shown in the figure. The diameter of the...
1. Water is flowing in a pipe as shown in the figure. The diameter of the cross section area A1 is twice the diameter of A2. The velocity of flow v1 is 2.00m/s while h and h2 are 5.00 cm and 30.0 cm, respectively. Take the density of water to be 1000. kg/m3 (a) Find v2 (b) Calculate the pressure difference P P2 between the two ends of the pipe 2
Water at 20 C is steadily flowing through a diverging pipe section that is inclined by...
Water at 20 C is steadily flowing through a diverging pipe section that is inclined by an angle of 30° with respect to the horizontal (See the figure) The total testing section length is 20 m long with an initial pipe diameter of 10 mm (Section 1) and final diameter of 20 mm (Section 2). The small diameter section shows a gage pressure of 100 kPa and average flow velocity 10 m/s. Other values will be obtained by reaching complete...
In a section of horizontal pipe with a diameter of 4.0 cm, the pressure is 47...
In a section of horizontal pipe with a diameter of 4.0 cm, the pressure is 47 kPa and water is flowing with a speed of 2.0 m/s. The pipe narrows to 2.0 cm. What is the pressure in the narrower region? Treat the water as an ideal incompressible fluid. The density of water is 1000 kg/m3 . (1 kPa = 1000 Pa)
Water is flowing through a horizontal pipe with diameter, D1, at
a velocity, V1, and under a pressure, P1. It enters a 900 reducing
bend (Shown in grey in Fig 2) that connects to a vertical pipe of
diameter, D2. The inlet of the bend is 50 cm above the exit of the
bend (as shown in Fig 2). Axes for positive directions of x and z
coordinates are provided. Figure 2 Side view of reducing bend from
horizontal to...
Water is flowing through a horizontal pipe with an inside diameter of 8.00cm. The pipe narrows to an inside diameter of 3.75cm. Assume the water is an ideal incompressible fluid. What is the velocity of the fluid initially, v_1 (when It is flowing in the 8.00cm diameter section) if the velocity of the water in the narrow part of the pipe is measured at V_2 = 27m/s? If the initial pressure is known to be 670 kPa what is the...
Water flows at speed of 6 m/s through a horizontal pipe of
diameter 3.5 cm. The gauge pressure P1 of the water in the pipe is
1.7 atm. A short segment of the pipe is constricted to a smaller
diameter of 2.4 cm .
What is the gauge pressure of the water flowing through the
constricted segment? Atmospheric pressure is 1.013 × 10^5 Pa. The
density of water is 1000 kg/m^3 . The viscosity of water is
negligible. Answer in...
Water moves through a pipe at 6
m/s under an absolute pressure of 330 kPa. The pipe narrows to one
half of its original diameter. What is the absolute pressure in the
narrow part of the pipe?
Water moves through a pipe at 6 m/s under an absolute pressure of 330 kPa. The pipe narrows to one half of its original diameter. What is the absolute pressure in the narrow part of the pipe? Pressure = Number Pascals
Water is flowing through a 10-cm-diameter water pipe at a rate of 0.1 m/s. Then, a diffuser with an outlet diameter of 20 cm is bolted to the pipe in order to slow down water as it exits the diffuser to atmospheric pressure, as shown in the given figure. Disregarding frictional effects, determine the force exerted on the bolts due to the water flow. Take the density of water to be 1000 kg/m3 -t- d 10 cmm D = 20...
1. Water is flowing in a pipe as shown in the figure. The diameter of the cross section area A1 is twice the diameter of A2. The velocity of flow v1 is 2.00m/s while h and h2 are 5.00 cm and 30.0 cm, respectively. Take the density of water to be 1000. kg/m3 (a) Find v2 (b) Calculate the pressure difference P P2 between the two ends of the pipe 2
Water at 20 C is steadily flowing through a diverging pipe section that is inclined by an angle of 30° with respect to the horizontal (See the figure) The total testing section length is 20 m long with an initial pipe diameter of 10 mm (Section 1) and final diameter of 20 mm (Section 2). The small diameter section shows a gage pressure of 100 kPa and average flow velocity 10 m/s. Other values will be obtained by reaching complete...
Most questions answered within 3 hours.
-
5. Explain the condition for a DC motor to develop the
maximum power. If a DC...
asked 5 minutes ago -
Compute the p[Ag] after 35.00 mL of 0.1 M silver nitrate has been
added to the...
asked 8 minutes ago -
Walgreen Company (NYSE: WAG) is currently trading at $48.50 on
the NYSE. Walgreen Company is also...
asked 21 minutes ago -
Based on historical data, your team knows what proportion of the
company's orders come from Males...
asked 39 minutes ago -
8. Which of the following atoms has the largest magnitude
electron affinity?
(a) Sodium (Na)
(b)...
asked 42 minutes ago -
Assess the two types of tests of cognitive abilities. (
regarding HR course)
asked 47 minutes ago -
1.Write an inspiring vision statement for an organization where
you work or have worked. If the...
asked 48 minutes ago -
2. Is fair trade coffee sustainable for the mass market,
or is it a niche product...
asked 49 minutes ago -
Please answer this asap in MATLAB.
In the following for loop, the the loop is executed...
asked 1 hour ago -
A 50.0-g golf ball is driven from the tee with an initial speed
of 44.6 m/s...
asked 56 minutes ago -
Use the molar concentration of the 50 mL solution to calculate
the moles of Cr(III) in...
asked 58 minutes ago -
Calculate the molarity of Fe3+ in solution A.
Solution A: 10 mL of 0.0600 M Fe(No3)3 ...
asked 1 hour ago