Homework Answers
Add Answer to:
QUESTION 5 The below beam is loaded with equal forces of 4 kN, each is located...
The beam is loaded as shown in the diagram below. The beam is uniformly loaded at...
The beam is loaded as shown in the diagram below. The beam is uniformly loaded at 3 kN/m for the length of 4 m from B. The beam also has two point loads, 4 KN at 2 m from A and 3 KN at 3 m from B. 2 KN 3 KN 3KN/m A 2 m 2 m 11 m 3 m Fig. Q2 Draw a shear force and bending moment diagram. Also determine the location of maximum bending moment...
Point loads are 1.2 kN and 1.5 kN respectively 5. Fabricated box beam The simply supported beam is loaded by two forces...
Point loads are 1.2 kN and 1.5 kN respectively
5. Fabricated box beam The simply supported beam is loaded by two forces as shown below. The beam is constructed from four 24 mm thick boards which are nailed together. Determine the maximum distance s between nails if each nail can carry a force of Fallowable = 275N. 1.5 KN 1.2 KN 24 mm 177 mm 24 mm 3.0 m 2.5 m 1.0 m 24 mm 24 mm 280 mm
5....
The beam has a fixed support at A and is loaded by two forces and a...
The beam has a fixed support at A and is loaded by two forces and a couple. Draw the free-body diagram of the beam and apply equilibrium to determine the reactions at A 4 kN 2 kN 6 kN-m 60° m++-1.5 m 1.5 m
4. A T-shaped cross-sectional beam is loaded as shown in the figure. Determine the following a....
4. A T-shaped cross-sectional beam is loaded as shown in the figure. Determine the following a. Sketch the internal shear force and bending moment diagrams for the beam. b. Calculate the maximum magnitude of the bending stress. Indicate where this occurs on the cross-section and along the length of the beam. c. Calculate the transverse shearing stress at the centroid of the cross-section using the maximum magnitude of the transverse shear force. - 200 mm 8 KN 1.5 kN/m 20...
The beam shown below is loaded with three forces, P - 100 KN, Q-200 KN, and S 200 KN acting at th...
The beam shown below is loaded with three forces, P - 100 KN, Q-200 KN, and S 200 KN acting at the free end of the cantilever beam. Determine (a) the maximum tensile and compressive stress of the bar if the depth, d of the rectangular bar is 70 mm, and the maximum torsional stress 200 Kw b-40 mm a 20 mm 20 mm
The beam shown below is loaded with three forces, P - 100 KN, Q-200 KN, and...
The beam shown below is loaded with three forces, P - 100 KN, Q-200 KN, and...
The beam shown below is loaded with three forces, P - 100 KN, Q-200 KN, and S 200 KN acting at the free end of the cantilever beam. Determine (a) the maximum tensile and compressive stress of the bar if the depth, d of the rectangular bar is 70 mm, and the maximum torsional stress 200 Kw b-40 mm a 20 mm 20 mm
QUESTION 1 [25 marks A frame loaded with a uniformly distributed load at Member AB and...
QUESTION 1 [25 marks A frame loaded with a uniformly distributed load at Member AB and point load at Member BC and joint B. It has pinned supports A and C, while joint B is fixed connected, as can be seen in Figure 1. Take E-200 GPa. a) Using the slope-deflection method, calculate the moments and illustrate the bending moment diagram. [15 marks) b) Then calculate the shear forces and sketch the shear force diagram. [10 marks) 22 KN 10...
For the beam shown below (neglect self-weight of the beam) 16 kN x 8 mm 19...
For the beam shown below (neglect self-weight of the beam) 16 kN x 8 mm 19 kN 10 kN/m T 2 mm mm A4n - 3 m +3m → a. Draw the shear force and bending moment diagram. 2 mm Section X-X b. For the cross section x-x given, calculate the maximum tensile and compressive bending stress c. For the cross section X-X given, calculate the maximum shear stress
Moving to another question will save this response Question 10 Calculate the vertical force component of the 40 kN for the beam loaded as shown in the figure below 10kN 0 kN 20kN 30kN A 2m 4 m 4m...
Moving to another question will save this response Question 10 Calculate the vertical force component of the 40 kN for the beam loaded as shown in the figure below 10kN 0 kN 20kN 30kN A 2m 4 m 4m -39 4 KN
Moving to another question will save this response Question 10 Calculate the vertical force component of the 40 kN for the beam loaded as shown in the figure below 10kN 0 kN 20kN 30kN A 2m 4 m...
For the beam shown in below, determine the displacements and rotations at the nodes, the forces in each element, and reactions. Also, draw the shear force and bending moment diagrams 10 kN 2 E210 GPa...
For the beam shown in below, determine the displacements and rotations at the nodes, the forces in each element, and reactions. Also, draw the shear force and bending moment diagrams 10 kN 2 E210 GPa .20 kN m
For the beam shown in below, determine the displacements and rotations at the nodes, the forces in each element, and reactions. Also, draw the shear force and bending moment diagrams 10 kN 2 E210 GPa .20 kN m
The beam is loaded as shown in the diagram below. The beam is uniformly loaded at 3 kN/m for the length of 4 m from B. The beam also has two point loads, 4 KN at 2 m from A and 3 KN at 3 m from B. 2 KN 3 KN 3KN/m A 2 m 2 m 11 m 3 m Fig. Q2 Draw a shear force and bending moment diagram. Also determine the location of maximum bending moment...
Point loads are 1.2 kN and 1.5 kN respectively
5. Fabricated box beam The simply supported beam is loaded by two forces as shown below. The beam is constructed from four 24 mm thick boards which are nailed together. Determine the maximum distance s between nails if each nail can carry a force of Fallowable = 275N. 1.5 KN 1.2 KN 24 mm 177 mm 24 mm 3.0 m 2.5 m 1.0 m 24 mm 24 mm 280 mm
5....
The beam has a fixed support at A and is loaded by two forces and a couple. Draw the free-body diagram of the beam and apply equilibrium to determine the reactions at A 4 kN 2 kN 6 kN-m 60° m++-1.5 m 1.5 m
4. A T-shaped cross-sectional beam is loaded as shown in the figure. Determine the following a. Sketch the internal shear force and bending moment diagrams for the beam. b. Calculate the maximum magnitude of the bending stress. Indicate where this occurs on the cross-section and along the length of the beam. c. Calculate the transverse shearing stress at the centroid of the cross-section using the maximum magnitude of the transverse shear force. - 200 mm 8 KN 1.5 kN/m 20...
The beam shown below is loaded with three forces, P - 100 KN, Q-200 KN, and S 200 KN acting at the free end of the cantilever beam. Determine (a) the maximum tensile and compressive stress of the bar if the depth, d of the rectangular bar is 70 mm, and the maximum torsional stress 200 Kw b-40 mm a 20 mm 20 mm
The beam shown below is loaded with three forces, P - 100 KN, Q-200 KN, and...
The beam shown below is loaded with three forces, P - 100 KN, Q-200 KN, and S 200 KN acting at the free end of the cantilever beam. Determine (a) the maximum tensile and compressive stress of the bar if the depth, d of the rectangular bar is 70 mm, and the maximum torsional stress 200 Kw b-40 mm a 20 mm 20 mm
QUESTION 1 [25 marks A frame loaded with a uniformly distributed load at Member AB and point load at Member BC and joint B. It has pinned supports A and C, while joint B is fixed connected, as can be seen in Figure 1. Take E-200 GPa. a) Using the slope-deflection method, calculate the moments and illustrate the bending moment diagram. [15 marks) b) Then calculate the shear forces and sketch the shear force diagram. [10 marks) 22 KN 10...
For the beam shown below (neglect self-weight of the beam) 16 kN x 8 mm 19 kN 10 kN/m T 2 mm mm A4n - 3 m +3m → a. Draw the shear force and bending moment diagram. 2 mm Section X-X b. For the cross section x-x given, calculate the maximum tensile and compressive bending stress c. For the cross section X-X given, calculate the maximum shear stress
Moving to another question will save this response Question 10 Calculate the vertical force component of the 40 kN for the beam loaded as shown in the figure below 10kN 0 kN 20kN 30kN A 2m 4 m 4m -39 4 KN
Moving to another question will save this response Question 10 Calculate the vertical force component of the 40 kN for the beam loaded as shown in the figure below 10kN 0 kN 20kN 30kN A 2m 4 m...
For the beam shown in below, determine the displacements and rotations at the nodes, the forces in each element, and reactions. Also, draw the shear force and bending moment diagrams 10 kN 2 E210 GPa .20 kN m
For the beam shown in below, determine the displacements and rotations at the nodes, the forces in each element, and reactions. Also, draw the shear force and bending moment diagrams 10 kN 2 E210 GPa .20 kN m
Most questions answered within 3 hours.
-
Question 10
Applied Materials depreciates buildings and improvements over
useful lives of 5-50 years.
a.
True....
asked 5 minutes ago -
A 10.0 mL sample of 0.25 M NaOH(aq) is titrated with 40.0 mL of
0.10 M...
asked 6 minutes ago -
How
can we prove that a flow is incompressible if the velocity field is
known?
asked 8 minutes ago -
It is sometimes argued that understanding people's existing
activities does not really help to design future...
asked 11 minutes ago -
what is the angular velocity of tje moon in its orbut ( orbit
period is 28)?
asked 12 minutes ago -
Time Off At Superior Software Service
As she hangs up the telephone, Joan Jackson realizes that...
asked 15 minutes ago -
Use the sample data and confidence level given below to complete
parts (a) through (d).
A...
asked 17 minutes ago -
1. Consider a risky portfolio. The end-of-year cash flow derived
from the portfolio will be either...
asked 18 minutes ago -
Find the critical value(s) for the specified Wilcoxon
signed-rank test.
Sample size = 10, two-tailed test,...
asked 52 minutes ago -
why don't arctic animals feet freeze in winter biology
question
asked 35 minutes ago -
Cellular respiration in eukaryotes has the same purpose as
fermentation in prokaryotes
True
False
asked 37 minutes ago -
A random sample of size n = 32 is taken from a
population with mean μ...
asked 47 minutes ago