Fluid power system Do all of your work on these sheets, if extra room is required,...
For the following circuit; if: The pressure drop from point A to B is 9 psi, The pressure drop from point C to D is 10 psi, The pressure drop from point D to E is 72 psi, And the pressure drop from E to F is 120 psi What is the Temperature Rate of Rise for the oil in the reservoir, if the reservoir contains 15 gallons of fluid, the pump flow is 15 GPM, the fluid has a...
Hydraulic Press 11.0ft Flow 10.0 ft 2.0ft 6 3.0 ft Filter Pump Flow The diagram on the next slide shows a fluid power system for a hydraulic press The following is known: The volume flow rate is 35 gpm. The hydraulic fluid has a specific gravity of 0.87 The power input to the pump is 20 hp. The pump efficiency is 80 percent. The filter has a resistance coefficient K-1.85 based on the velocity head in the suction line All...
ees nleliees show are not that the fluid property calculations described later great, however, dhe differen dne diff dhis field operating conditions ter should use the results of a separator test performed at these differences 10-3%Data from a separator test on a black oil aregiven Below. Note that the volume of separator liquid was measured at separator pressure and temperature before it was released to the stock tank. Prepare a separator test table for the reservoir fluid study Volume of...
The diagram on the next slide shows a fluid power system for a hydraulic press The following is known: The volume flow rate is 35 gpm. The hydraulic fluid has a specific gravity of 0.87 and v-4.30x104 ft/s. The power input to the pump is 20 hp. The pump efficiency is 80 percent. The filter has a resistance coefficient K-1.85 based on the velocity head in the suction line. All piping is 2-in schedule 40 steel. The total length of...
34. A coal slurry is found to behave as a power law fluid, with a flow index of 0.3, a specific gravity of 1.5, and an apparent viscosity of 70 cP at a shear rate of 100/s. What volumetric flowrate of this fluid would be required to reach turbulent flow in a 1/2 in. ID smooth pipe, which is 15 ft long? What is the pressure drop in the pipe (in psi) under these conditions? Please show all work, thank...
HELPPPP 5 Hydraulic Press ●4 11.0 ft Flow 10.0 ft 2.0 ft 1 6 3.0 ft Filter Pump Flow The diagram on the next slide shows a fluid power system for a hydraulic press. The following is known: The volume flow rate is 35 gpm. The hydraulic fluid has a specific gravity of 0.87 and v-4.30X10+ ft'/s. The power input to the pump is 20 hp. . The pump efficiency is 80 percent. The filter has a resistance coefficient K-1.85...
Chemical Engineering Fluid Mechanics 30. The purpose of a centrifugal pump is to increase the pressure of a liquid in order to move it through a piping system. The pump is driven by a motor, which must provide sufficient power to operate the pump at the desired conditions. You wish to find the pressure developed by a pump operating at a flow rate of 300 gpm with an oil having a specific gravity (SG) of 0.8 and a viscosity of...
You must show ALL work for full credit. Also, it needs to be LEGIBLE. Label and BOX all answers. 1. (100 points) Water at 25°C is pumped at a rate of 0.075m/s from a reservoir 20m above a pump to a free discharge (this means discharged to atmosphere) 35m above the pump. The pressure on the intake side of the pump is 150kPa and the pressure on the discharge side of the pump is 450kPa. The pipe between the reservoir...
fluid Q1: A venture meter is fitted in a pipe of 30 cm diameter inclined at 40° to the horizontal to measure the flow rate of petrol having a specific gravity of 0.8. The ratio of areas of main pipe and throat is 5 and the throat is at 1 m from the inlet along its length. The difference in manometer head is 40 mm of mercury. Assuming the coefficient of discharge as 0.96. Calculate the discharge through the venture...
Show your work [14 Marks] 23. Oil has a Specific gravity 0.75 is flowing through a siphon as shown in the diagram calculate the following: a) The velocity of the oil at exit (using Bernoulli's) b) The volumetric flow rate of oil from the tank c The flow velocity in the 60 mm diameter section of the pipe d) The pressure at point B 3.0 m se-0.75 60 mm Diameter 100m 30 mm Diameter Show your work [14 Marks] 23....