Homework Answers
Add Answer to:
(c) The diagram below shows part of the heating circuit of a domestic shower. insulated wire...
(+30) You have a half-filled hot tub that is cold (T-25 "C). You have two ways...
(+30) You have a half-filled hot tub that is cold (T-25 "C). You have two ways of heating it up: add more hot water (maximum T = 45 "C) and/or turn on the electric heater (5 kW). The total water capacity of your well-insulated hot tub is 1.0 m3, and the desired water temperature is 38"c. a. If you just use the electric heating element to heat up the existing water, without adding any new hot water: i. (+8) How...
5-30 Air enters an adiabatic nozzle steadily at 300 kPa, 200°C, and 30 m/s and leaves...
5-30 Air enters an adiabatic nozzle steadily at 300 kPa, 200°C, and 30 m/s and leaves at 100 kPa and 180 m/s. The inlet area of the nozzle is 80 cm². Determine (a) the mass flow rate through the nozzle, (b) the exit temperature of the air, and (c) the exit area of the nozzle. Answers: (a) 0.5304 kg/s, (b) 184.6°C, (c) 38.7 cm P = 300 kPa T, = 200°C Vi = 30 m/s A = 80 cm AIR...
The figure shows a schematic of a power plant that has two steam turbines. The water...
The figure shows a schematic of a power plant that has two steam turbines. The water (the working fluid for the plant) leaves the high pressure turbine (HPT) as saturated vapour at 1000 [kPa]. Part of this flow is diverted to an insulated heat exchanger, which we hot airstream to create superheated steam that enters the low pressure turbine (LPT). The air mas flow rate is 19.5 k/s and the air temperature drops from 1100 to 6001 as it goes...
The figure shows a schematic of a power plant that has two steam turbines. The water...
The figure shows a schematic of a power plant that has two steam turbines. The water (the working fluid for the plant) leaves the high pressure turbine (HPT) as saturated vapour at 1000 [kPa]. Part of this flow is diverted to an insulated heat exchanger, which uses a hot air stream to create superheated steam that enters the low pressure turbine (LPT). The air mass flow rate is me=19.5 kg/s) and the air temperature drops from 1100 to 600°Cas it...
Homework 7 heat transfer 2018-20 1) A horizontal tube of 12.5-mm dimeter with an outer srface temperature of 240°C is placed in a room with an air temperature of 20°C. Estimate the heat transfer rate...
Homework 7 heat transfer 2018-20 1) A horizontal tube of 12.5-mm dimeter with an outer srface temperature of 240°C is placed in a room with an air temperature of 20°C. Estimate the heat transfer rate per unit length of the tube due to free convection. 2) Air at -10°C flows at 10 m/s over the roof plate of two 5m length rooms whose air is at Too-200C. The roof plate is 0.20-m thick concrete (k = 0.6 w/ m. K)....
4. The open-circuit voltage of a battery is 12 volts and it's internal (i.e., source) resistance ...
please do 4, and 5
4. The open-circuit voltage of a battery is 12 volts and it's internal (i.e., source) resistance is one ohm. Using a load resistor as a heating element to extract maximal power from the battery to heat up a container of 1 cubic meter of water (to be used as a thermal reservoir for a steam engine). (a) How long (i.e., how many seconds) does it take to bring that water from 32 degrees Celsius to...
Two large parallel plates with surface conditions approximating those of a blackbody are maintained at 800°C...
Two large parallel plates with surface conditions approximating those of a blackbody are maintained at 800°C and 100°C, respectively. Determine the rate of heal transfer by radiation between the plates in Wim and the radiative heat transfer coefficient in W/m K ) 12 Write down the one-dimensional sent heal conduction equation for a plane wall with constant thermal conductivity and heat generation in its simplest form, and indicate what each variable represents 13 Write down the one-dimensional transient heat conduction...
1 CPD4701 Assignment 2/2019 Question 2 shell and-tube heat exchanger was designed for the following service: Cold strea...
1 CPD4701 Assignment 2/2019 Question 2 shell and-tube heat exchanger was designed for the following service: Cold stream Hot stream Crude Oil Fluid Cooling water Tube side Stream allocation Shell side Mass flow rate (kg/s) 110 30 Inlet temperature (C) 90 Outlet temperature (C) Heat capacity (J/kg K) Density (kg/m2) Viscosity (Pa-s) Thermal conductivity (W/m-K) Fouling factor (m2 CW) 40 50 2177 4187 787 995 0.72-10 1.89-103 0.122 0.59 0.0002 0.0004 The shell and tube heat exchanger has the following...
1 CPD4701 Assignment 2/2019 Question 2 shell and-tube heat exchanger was designed for the following service: Cold strea...
1 CPD4701 Assignment 2/2019 Question 2 shell and-tube heat exchanger was designed for the following service: Cold stream Hot stream Crude Oil Fluid Cooling water Tube side Stream allocation Shell side Mass flow rate (kg/s) 110 30 Inlet temperature (C) 90 Outlet temperature (C) Heat capacity (J/kg K) Density (kg/m2) Viscosity (Pa-s) Thermal conductivity (W/m-K) Fouling factor (m2 CW) 40 50 2177 4187 787 995 0.72-10 1.89-103 0.122 0.59 0.0002 0.0004 The shell and tube heat exchanger has the following...
(+30) You have a half-filled hot tub that is cold (T-25 "C). You have two ways of heating it up: add more hot water (maximum T = 45 "C) and/or turn on the electric heater (5 kW). The total water capacity of your well-insulated hot tub is 1.0 m3, and the desired water temperature is 38"c. a. If you just use the electric heating element to heat up the existing water, without adding any new hot water: i. (+8) How...
5-30 Air enters an adiabatic nozzle steadily at 300 kPa, 200°C, and 30 m/s and leaves at 100 kPa and 180 m/s. The inlet area of the nozzle is 80 cm². Determine (a) the mass flow rate through the nozzle, (b) the exit temperature of the air, and (c) the exit area of the nozzle. Answers: (a) 0.5304 kg/s, (b) 184.6°C, (c) 38.7 cm P = 300 kPa T, = 200°C Vi = 30 m/s A = 80 cm AIR...
The figure shows a schematic of a power plant that has two steam turbines. The water (the working fluid for the plant) leaves the high pressure turbine (HPT) as saturated vapour at 1000 [kPa]. Part of this flow is diverted to an insulated heat exchanger, which we hot airstream to create superheated steam that enters the low pressure turbine (LPT). The air mas flow rate is 19.5 k/s and the air temperature drops from 1100 to 6001 as it goes...
The figure shows a schematic of a power plant that has two steam turbines. The water (the working fluid for the plant) leaves the high pressure turbine (HPT) as saturated vapour at 1000 [kPa]. Part of this flow is diverted to an insulated heat exchanger, which uses a hot air stream to create superheated steam that enters the low pressure turbine (LPT). The air mass flow rate is me=19.5 kg/s) and the air temperature drops from 1100 to 600°Cas it...
Homework 7 heat transfer 2018-20 1) A horizontal tube of 12.5-mm dimeter with an outer srface temperature of 240°C is placed in a room with an air temperature of 20°C. Estimate the heat transfer rate per unit length of the tube due to free convection. 2) Air at -10°C flows at 10 m/s over the roof plate of two 5m length rooms whose air is at Too-200C. The roof plate is 0.20-m thick concrete (k = 0.6 w/ m. K)....
please do 4, and 5
4. The open-circuit voltage of a battery is 12 volts and it's internal (i.e., source) resistance is one ohm. Using a load resistor as a heating element to extract maximal power from the battery to heat up a container of 1 cubic meter of water (to be used as a thermal reservoir for a steam engine). (a) How long (i.e., how many seconds) does it take to bring that water from 32 degrees Celsius to...
Two large parallel plates with surface conditions approximating those of a blackbody are maintained at 800°C and 100°C, respectively. Determine the rate of heal transfer by radiation between the plates in Wim and the radiative heat transfer coefficient in W/m K ) 12 Write down the one-dimensional sent heal conduction equation for a plane wall with constant thermal conductivity and heat generation in its simplest form, and indicate what each variable represents 13 Write down the one-dimensional transient heat conduction...
1 CPD4701 Assignment 2/2019 Question 2 shell and-tube heat exchanger was designed for the following service: Cold stream Hot stream Crude Oil Fluid Cooling water Tube side Stream allocation Shell side Mass flow rate (kg/s) 110 30 Inlet temperature (C) 90 Outlet temperature (C) Heat capacity (J/kg K) Density (kg/m2) Viscosity (Pa-s) Thermal conductivity (W/m-K) Fouling factor (m2 CW) 40 50 2177 4187 787 995 0.72-10 1.89-103 0.122 0.59 0.0002 0.0004 The shell and tube heat exchanger has the following...
1 CPD4701 Assignment 2/2019 Question 2 shell and-tube heat exchanger was designed for the following service: Cold stream Hot stream Crude Oil Fluid Cooling water Tube side Stream allocation Shell side Mass flow rate (kg/s) 110 30 Inlet temperature (C) 90 Outlet temperature (C) Heat capacity (J/kg K) Density (kg/m2) Viscosity (Pa-s) Thermal conductivity (W/m-K) Fouling factor (m2 CW) 40 50 2177 4187 787 995 0.72-10 1.89-103 0.122 0.59 0.0002 0.0004 The shell and tube heat exchanger has the following...
Most questions answered within 3 hours.
-
Prelab Problem: You have a parallel plate capacitor
with circular plates of radius
r = 10.0...
asked 18 minutes ago -
Fine Furniture, Inc. is a furniture manufacturer located in
Norfolk, Virginia. Fine enters into a contract...
asked 15 minutes ago -
Business Ethics
Who are those codes aimed at? Is that believable?
asked 13 minutes ago -
When a black hole of mass M1 merges with a black hole of mass
M2, it...
asked 23 minutes ago -
use
hardy wineberg equation to find equilbrium.
AA 150. Aa 120. aa 90
asked 43 minutes ago -
Why don't law enforcement or prosecutors always investigate
crimes as hate crimes
asked 34 minutes ago -
Describe how Rio Tinto is a main competitor of BHP.
asked 37 minutes ago -
Two children (m = 31.0 kg each) stand opposite each other on the
edge of a...
asked 44 minutes ago -
A 2180-kg car is slowed down uniformly from 24.6 m/s to 5.2 m/s
in 3.32 s....
asked 1 hour ago -
Jesse’s Machining is looking to buy a new machine to handle a
new four-year contract for...
asked 1 hour ago -
5. A slide mount of a fungal specimen is prepared. A slide and
coverslip are flame-sterilized....
asked 1 hour ago -
A parallel plate capacitor has a charge Q, plates of area A and
separation d, where...
asked 1 hour ago