Vi = - 2.5 V
Vnew = - 16 V
Determine the value of in voltage V in the rut s 15ΚΩ 1SV next If the...
Question 22 The Zener diode 1N4744A, shown in the figure, has Vz=15 V, IZK = 0.25 mA and IZM-72 mA. Determine the output voltage at the load RL 15092 SRL 1502 4.0 V 8V 15V
. Find the response voltage v) in the rut below i th independenure e isc (t)- 12 cos 100t +16 sin 100t A peak Leave the answer for v(t) in trigonometric form. Also find the impedance presented to the independent current source. (-24 cos 100t + 8 sin 100t, 5 +/5 Ω) 20 ohm 10 ohm 100 mH 0.21,(t) sc(t) SC
Use KVL to determine the Voltage Source Ez (V). E3 (V) = ? Is =2A E2 두 + V - - R4100 + 300 + E R2로L 8V 100 E3 두
2. In the following circuit, v,-20 Vrms (rms value). a) Determine the value of capacitor needed to provide filtering so that the voltage does not drop below 26 V. The load resistance Rioad may vary from 1.5 k2 to 2.5 k2. Assume the diode is ideal (Vox -0 V). b) Sketch v, and the output Vour waveforms. c) The filter capacitor often represents a significant economic factor in terms of cost, size, and weight in the design of rectifier circuit....
2. In the following circuit, v, 20 Vrms (rms value). a) Determine the value of capacitor needed to provide filtering so that the voltage does not drop below 26 V. The load resistance Rioad may vary from 1.5 kQ to 2.5 kQ. Assume the diode is ideal (VON 0 V). b) Sketch v, and the output vout waveforms. c) The filter capacitor often represents a significant economic factor in terms of cost, size, and weight in the design of rectifier...
To design a high efficiency d.c., to d.c power converter with the given specifications min 10V max 15V nominal (regulated) 8V Input voltage: Output voltage: Nominal load current: 4A Inductor current ripple: 0.1A max Switching frequency: 30 kHz Output voltage ripple: 20 mV Define a suitable power circuit topology to meet the above specification? Sketch a circuit diagram of the chosen power circuit topology (a) Define the minimum and maximum duty cycles assuming that the control circuit keeps the output...
18–40E A solar cell has an open circuit voltage value of 0.60 V with a reverse saturation current density of J. = 4.11 X 1010 A/ft?. (a) For a temperature of 75°F, determine the load voltage at which the power output is maximum. (b) If the solar irradiation is 220 Btu/h.ft?, determine the effi- ciency of the solar cell at a load voltage of 0.56 V. (c) Determine the cell area, in ft?, for a power output of 500 W...
4.9 Determine R1 and R2 to obtain a zero quiescent output voltage for the circuit shown in Figure P4.9 when the transistor has a β 200 and Va,--0.6V. (Assume RB-10 kQ) o Y out +8V 4.9 Determine R1 and R2 to obtain a zero quiescent output voltage for the circuit shown in Figure P4.9 when the transistor has a β 200 and Va,--0.6V. (Assume RB-10 kQ) o Y out +8V
5000 10.2 S pts) The Zener diode in the circuit on the right voltage V 20 = 8.5V., and Zener resistancerz the circuit on the right has a Zener d) Find the Thevenin equivalent circuit as seen by lo b) Find the output voltage if a loa Find the output voltage if a load R, is connected and it draws a 1.5 mA current. Determine the value of RL c) How small can the load R, be, while ensuring that...
Determine the minimum value for RL in the voltage divider below to create a "STIFF" load. R2 = 1702 Enter your results in Ohms - KS2. Do not type the unit. $3300 R1 15V Vs