steps rounded to four significant figures. Give your final answer(s) to three significant figures For the...
stepe rounded to four siguificant figures. Give your final anuwer() to three significant figures. Write your answer in scientific notation, ie in the form 12345 x 10, with the decimal poin following the first digit 18.2mm 18.2 mm 237m 18.2 mm 0 80 mm 10.1 The cross section of the bar shown is symmetric about the y axis Part I (a) Determine d so that the origin of the coordinate system, point centroid of the area. O,is positioned at the...
Do not round intermediate calculations; however, for display purposes report intermediate steps rounded to four significant figures. Give your final answer(s) to four significant figures. For the slider-crank mechanism shown, let R 23 mm, L 75 mm, and H 35 mm. If θ 1,700 rpm, determine the angular velocity of the connecting rod AB and the speed ofthe slider B for θ-90°. L. ac radis AB m/s Do not round intermediate calculations; however, for display purposes report intermediate steps rounded...
Do not round intermediate calculations; however, for display purposes, report intermediate steps rounded to three significant figures. Give your final answer(s) to three significant figures. Determine the support reactions using composite shapes for the distributed load. 12 kip/ft 18 ft - 18 ft kip kip kip .y B-
Your response: Do not round intermediate calculations, however for display purposes report intermediate steps rounded to four significant figures. Give your final answer(s) to three significant figures. Enter tension forces values as positive numbers and compression forces values as negative numbers 16 ft 7 ft 7 ft 4 ft 3.0 kip 3.0 kip 14 ft 6.6 kip 14 ft D E 4 ft 4 ft The electric power transmission tower supports two wires that apply 3.0-kip, vertical forces, and the...
Do not round intermediate calculations, however for display purposes report intermediate steps rounded to four significant figures. Give your final answer(s) to three significant figures Write your answer in scientific notation, i.e. in the form 1.2345 x 10°, with the decimal point following the first digit. 38 mm 38 mm 38 mm 165 mm 19 mm x Determine Ix and Iy 38 mm y 165 mm 19 mm X Determine Ix and Iy 4 mm x 10 (select) 4 mm...
Do not round intermediate calculations. Give your final answer(s) to three significant figures. Each of the links AB and CD is made of aluminum (E 73 GPa) and has a cross-sectional area of 110 mm*. Knowing that they support the rigid member BC, determine the deflection of point E. 4 kN 0.44 m 0.42 m 0.19 m
1 out of 4 attempts intermediate steps rounded to four significant figures, Give your final answer(s) to four significant figures wer(s) to four The position of a car as a function of time r, with r > 0 and expressed in seconds, is r (t)-1 (621-130) i, + (1.6 + 31.31-851/2)/1 ft. Determine the slope θ of the trajectory of the car for ti-l s and t2-3 s. In addition, find the angle o between velocity and acceleration for 1...
Do not round intermediate calculations. Give your final answer(s) to three significant figures. The beam shown is made of a nylon for which the allowable stress is 25 MPa in tension and 29 MPa in compression. Determine the largest couple M that can be applied to the beam 24 mm 21 mm 42 mm 12 mm N m
Do not round intermediate calculations. Give your final answer(s) to three significant figures. Determine the plastie moment Mp of a steel beam of the eross section shown, assuming the steel to be elastoplastic with a yield strength of250 MPa 48 mm 28 mm 10 mm 12 mm 28 mm м, kN m
Do not round intermediate calculations. Give your final answer(s) to three significant figures. Two cylindrical rods, one of steel and the other of brass, are joined at C and restrained by rigid supports at.A and E. For the loading shown and knowing that Es200 GPa and E b 105 GPa, determine the deflection of point C. Dimensions in imm 110 110 190140 D E Steel B Brass 60 KN 45 kN 40-mm diam 30-mm diam.