1 table spoon = 3 teaspoon
2 tea spoon = 2/3 table spoon
= 2×0.5/3
= 1/3 fluid ounce
= 1×29.574/3
= 9.86 mL
So volume is 9.86 mL
3. Determine the volume (in mL) of 2.0 teaspoon using the following relationships all with any...
Calculate the IV flow rate to administer the following medications by using a volume control set, and determine the amount of IV fluid and medication to be added to the chamber. The ordered time includes the flush volume Order: Cleocin 150 mg IV q.8h in 32 mL D5NS over 60 min on an infusion pump. Flush with 28 mL Supply: Cleocin 150 mg/mL Flow rate: Add JO mL/h mL medication and mL IV fluid to the chamber Total IV volume...
Using the following unit conversions: 1.00 fluid ounce = 29.573 ml, 1.00 L = 1000 cm^3 density of water = 1.00 gm/cm^3, the number of fluid ounces in a kg of water is
reaction one NaOH and HCl. 50.0 mL of 2.0 M HCl solution into
50.0 mL of 2.0 M NaOH
reaction two 50 mL OF 2.0 M NaOH into 50 mL of 2.0 M NH4Cl
reaction three 50.0 mL of 2.0 M HCl into 50.0 mL NH3
pleanse answer all of the questions
Experinen DATA TABLE Reaction 1 Reaction 2 Reaction 3 34,012。21 2H0 Maximum temperature (C) Initial temperature (C) Temperature change (&T) DATA ANALYSIS 1. Calculate the amount of heat...
1.If 23 ml of 2.0 M NaOH was required to neutralize 10.0 ml of HCl, what is the molarity of the HCl? 2.What volume (in L) of a 2.08 M NaOH solution is required to neutralize 0.53 mol of HCl? *Remember to report your answer using the proper significant digits. 4.A student has finished the titration of a sample of HBr of unknown concentration with 0.2 M NaOH. The student notices small drops of unreacted NaOH were left on the...
2. From the above graph, determine the pressure in torr if the volume is 84.2 mL. Show your work below: .68 3. Give the SI unit for pressure 4. Give the SI unit for volume 125 1. Plot the Pressure (Y-axis) vs. 1/Volume (X-axis) on graph paper below. UILE YOU I that, using a ruler, draw the best-fit line for the points you have plotted. 0 1 / Volume (mL) 0.0100 0. 011 0.0125 0.0143 0.0167 0.0200 Pressure (atm) 0.254...
30 Using the following equation determine the average concentration (moles per liter) of acetic acid (CH,CO,H) present in your vinegar. Record the concentration in Data Table 2 average volume of NaOH (mL) X 1L NAOH 1000 mL NAOH 0,5 mol NaOH 1. NaOH 1 mol CH4COH 1 mol NaOH = average moles of CH,CO,H average moles of CH,CO,H 5.0 ml, vinegar 1000 ml IL = Concentration of CH.CO, H (M=mol/L) 31 Using the following equation and your result from Step...
Ascorbic Acid Concentration (g/L)
Volume of DCPIP in Full Syringe Used (mL)
Volume of DCPIP in Final Syringe (mL)
Total Volume of DCPIP Used (mL)
0.0
5 mL
4.9 mL
0.1 mL
0.50
5 mL
2 mL
3 mL
1.00
5 mL
1.2 mL
3.8 mL
1.50
5 mL
3.6 mL
6.4 mL
2.00
5 mL
2.8 mL
7.2 mL
Unknown Trial 1
5 mL
2.0 mL
3.0 mL
Unknown Trial 2
5 mL
2.2 mL
2.8 mL
Unknown Trial...
Standardization Data Trial 1 Trial 2 Trial 3 Volume of 0.500 M KHP 5.00 ml 5.00 ml 5.00 ml Initial burette reading 0.00 ml 13.10 ml 26.60 ml 26.60 ml 13.20 ml Final burette reading 13.10 ml 13.10 ml Volume of base used (final-initial readings) Data Analysis: (work alone on calculations) 39.60 ml 13.00 ml 3. Calculate the molarity of base for each trial. Use dimensional analysis - show all unit conversions (hint: start with mL of KHP solution used)....
3. For following input/output system relationships, determine the impulse response h(t). Clearly show all the steps arriving to your answer. p(-)x(1-)a L(2- r)x(1)dr-L*-1)x(1)dr (10 points) y(t) a. b. (10 points) y(t) -00 4. (10 points) An LTI system has the impulse response: h(t) = 4e-0.75(-1)[u(t + 4) - u(t - 10)]. this system Causal or Non-Causal? You must justify your answer. A correct answer with no justification worth only 4 points Is
3. For following input/output system relationships, determine the...
the information on the left is needed to answer the questions
on the right.
Forcach of the following dimensional any probleme underline the requested information and circle the starting in Create a gyor h ows you to convert from the starting units to the r est is using the qualities from the above se relor back to step 15 of the strategy Save the m ain with the cadwaring information and wing your conversion factors to implement your un plan...