Please only use PSpice as stated in the directions. Any other software will not be accepted. Thanks
No multisim or LTSpice.
Case:1
R2=330k;Vbb=10v
Ib= (Vbb-Vbe)/R2= (10-0.7)/330k = 28.28 micro A.
________________________________________________________________________________
Case:2
R2=147k;Vbb=10v
Ib= (Vbb-Vbe)/R2= (10-0.7)/147k =63.26 micro A.
Please only use PSpice as stated in the directions. Any other software will not be accepted....
Electronics-common emmitter amplifier. Pls be try to be helpful Im trying to study here in this book example.. However im kinda lost and i cant follow the correct answers they got.. could someone pls help me.. I just wanna learn this, i hope u can help me learn by showin clear and corect solutions on how to properly got the answer.. Also especially on finding the values on the laod line analysis, im lost. Pls help Any helpful help would...
4. Lab VIII: Experiment VII The Bipolar Junction Transistor (BJT) Characteristics The bipolar junction transistor (BJT) is a three-terminal solid state device widely used as an amplifier (or switching) device. It consists of two n-type materials sandwiched by p-type material (npn) or two p-type and n-type. The terminals (sections) are known as emitter E, base B and collector C. Two currents and two voltages uniquely describe the behavior of the device. The third current/voltage can be determined through KCL/KVL. See...
Electronics1. It's a multiple choices question. use the formula sheet if needed (the last picture). Question 3 CIRCUIT B1 (2.5 Marks) + VC Rc IRC < + RB IC IB V ce → IE FIG. 3: CIRCUIT B1 Statement: Sketching relevant output (V-Ic) characteristics decide on Q-point coordinates and DC load-line details: That is, determine DC operating conditions of the NPN-BJT/Si circuit of Fig.3 (denoting the type Circuit B1). Assume the following: Vcc= 20 volt; Rc = 2.5 k; RB...
PLEASE SHOW ALL WORK AND TO FOLLOW DIRECTIONS. PLEASE USE PSPICE. STUDENT ID= 7220849 2. Using a DC Sweep analysis to generate a table of values in the .OUT file: See Circuit 2 below: Let R1 through R6 equivalent to the digits 1 through 6 in your StudentID in k12 (use 10 k22 for a digit of 0). • For example, if your StudentID is 9870654 then R1 =9 kN, R2 =8 kN, R3 = 7kN, R4 = 10KN, R5...
Electronics1. It's a multiple choices question. use the formula sheet if needed (the last picture). Question 4 CIRCUIT B2 (2.5 Marks) +Voc R ler Vic RS IB Vc V. RE FIG.4: CIRCUIT B2 Statement: Sketching relevant output (VIC) characteristics decide on Q-point coordinates and DC load-line details: That is, determine DC operating conditions of the NPN-BJT/Si circuit of Fig. 4 (denoting the type Circuit B2). Assume the following: Vor = 24 volt; Rc = 5.0 k; Re = 1000 ohm:...
PLEASE SHOW ALL WORK AND TO FOLLOW DIRECTIONS. PLEASE USE PSPICE. STUDENT ID= 7220849 3. Using a DC Sweep analysis to graph currents and voltages Let R1 through R4 equivalent to the digits 1 through 4 in your StudentID in k 2 (use 10 k12 for a digit of 0). • For example, if your StudentID is 9870654 then R1 =9 KS2, R2 =8 kN, R3 = 7k2 and R4 = 10k12 A. Analyze Circuit 3 by hand to determine...
PLEASE SHOW ALL WORK AND TO USE PSPICE AND FOLLOW ALL DIRECTIONS. STUDENT ID=378564 Assignment: 1. For the Circuit 1 shown below: A. Analyze the circuit by hand as described in the textbook. B. Analyze the circuit using PSPICE as follows: Use a Bias Point analysis to find the quantities found in part A above. Be sure to add text to the schematic as indicated in the Sample Report. Adjust the placement of each value on the schematic so that...
Could someone please help me on how I should be configuring the circuit in Figure 4(a) in Multisim? Basically not understanding question #1 in the Procedure. Cannot keep Vrb the same value while adjusting Vcc. Then when trying to adjust Vbb to hold Vrb, Ib changes. Any help is appreciated! Discrete Devices Section LAB 4 BJT CHARACTERISTICS AND BIASING Objective: The objective of this laboratory is to examine the operation of a bipolar junction transistor and plot its output characteristics...