An 8.62 kg block of ice at 0 ?C is sliding on a rough horizontal icehouse floor (also at 0 ?C) at 15.7 m/s . Assume that half of any heat generated goes into the floor and the rest goes into the ice. A) How much ice melts after the speed of the ice has been reduced to 10.4 m/s ? B) What is the maximum amount of ice that will melt?
An 8.62 kg block of ice at 0 ?C is sliding on a rough horizontal icehouse...
A 5-kg sled is sliding on a horizontal rough surface with a speed of 18 m/s. The coefficier kinetic friction between the block and surface is 0.15. After travelling 25-m, it encounters as covered hill (where friction can be ignored) and slides uphill. The hill makes an angle of 38。 horizontal. (a) How much work is done against friction during the 25-m horizontal travel? the maximum elevation on the hill the block reaches? (c) How much work is done against...
Chapter 12, Problem 067 Chalkboard Video Interactive Solution 12.6Z provides a model for solving problems such as this. A 33.9-kg block of ice at 0 °C is sliding on a horizontal surface. The initial speed of the ice is 9.39 m/s and the final speed is 3.61 m/s. Assume that the part of the block that melts has a very small mass and that all the heat generated by kinetic friction goes into the block of ice, and determine the...
A block of ice at 0oC whose mass initially is m = 42.1 kg slides along a horizontal surface, starting at a speed v0 = 2.35 m/s and finally coming to rest after traveling a distance d = 2.93 m. Compute the mass of ice melted as a result of the friction between the block and the surface. (Assume that all the heat generated owing to friction goes into the block of ice.)
#7 Achild and sled with a combined mass of50 kg sliding down a hill from rest would 14pts. have the speed of 3.0 m/s at the bottom, if there was no friction. a) What is the height of the hill? If the actual speed at the bottom is 2.5 m/s how much work is done by frction? #8 A 7.00 g lead bullet at 25°C traveling at 250. ms is stopped by a tree. Assuming that 65% 14pts. of the...
A 2 kg block is sliding down a plane inclined at 30˚ to the horizontal. The coefficient of friction between the block and the plane is 0.25. How much work is done by gravity if the block slides 5 m? How much work is done by friction? If the block starts from rest, what is its speed after sliding the 5 m?
C. A 15 0-kg box has a rubber bottom. It is sliding on a horizontal sheet of ice with a 30.0 force applied to it. Coefficient of friction is 0.22 Determine: a. The force of friction on the box The acceleration of the box c. Later, the horizontal force is reduced to 20.0-N. Determine the acceleration of the box for this condition. d. Is this static of kinetic friction D. A block is pulled along a horizontal surface by a...
A 1.65 kg block of ice at 0°C is added to a pienic cooler. How much heat will the ice remove as it melts to water at 0°C? kcal
.1. A 2.50 kg block of ice at 0°C is added to a picnic cooler. How much heat (in kcal) will the ice remove as it melts to water at 0°C? 2. A 300.0 g pot of water at room temperature (25.0°C) is placed on a stove. How much heat (in kcal) is required to change this water to steam at 100.0°C? 3. Spent steam from an electric generating plant leaves the turbines at 110.0°C and is cooled to 95.0°C liquid water...
013 10.0 points An iron nail is driven into a block of ice by a single blow of a hammer. The hammerhead has a mass of 0.6 kg and an initial speed of 2 m/s. Nail and hammer are at rest after the blow. How much ice melts? Assume the tempera- ture of both the ice and the nail is 0°C before and after. The heat of fusion of ice is 80 Answer in units of g.
A block of mass 3 kg is sliding up a rough, 30° ramp. Its speed drops from 6 m/s to 2 m/s over a travel distance of 2 meters. .a. What is the change in the kinetic energy of the block? b. How much total work is done on the block by gravity? c. How much total work is done on the block by friction? d. What is the change in the gravitational potential energy of the block? e. What...