A cone floats in Glycerin (SG = 1.26), as shown in the figure. Find the mass...

Question

Question

A cone floats in Glycerin (SG = 1.26), as shown in the figure. Find the mass of the cone.

A cone floats in the glycerin (SG 1.26), as shown in the figure. Find the mass of the cone. FIGURE P3-103 h-30 cm Ir 60 cm SG

Answer 1

Answer #1

thn 90 91 -CM,

Answer 2

Similar Homework Help Questions

Question 12 10 pts For 0.15 m/s of glycerin at 40°C (sg = 1.26, dyn viscosity...

Question 12 10 pts For 0.15 m/s of glycerin at 40°C (sg = 1.26, dyn viscosity = 0.3 Paos from ApxD) flowing in the chamber outside of the square tubes as shown in the figure. Determine the Reynolds number. Both 200 mm square outside - 400 mm hs - 600 mm NT NE
Find surface area of cone shown below. Round to the nearest tenth. The figure is not...

Find surface area of cone shown below. Round to the nearest tenth. The figure is not drawn to scale. 21 cm 9 cm
Gate AB in Figure A2 is a homogeneous mass of 180 kg, 1.2 m wide into...

Gate AB in Figure A2 is a homogeneous mass of 180 kg, 1.2 m wide into the paper, hinged at A, and resting on a smooth bottom at B. All fluids are at 200 C. a) If the moment about the centre of gravity of a submerged plate at an angle e is defined as FYCP = Then show that this moment is given by [5marks] [3 marks b) Draw a diagram with all forces acting on the gate AB...

Use cylindrical coordinates to find the volume of the cone shown in the figure:

Use cylindrical coordinates to find the volume of the cone shown in the figure: a) [3 points] Set up integral to find the volume b) [2 points] Evaluate the integralc) [5 points] Show that z = h(1-r/r0), where r is a radius of a circular cross-section of the cone parallel to xy-plane.
A small object with mass m is placed in an inverted cone as shown. The cone...

A small object with mass m is placed in an inverted cone as shown. The cone is rotating around its vertical axis with a period of T. If the block is to remain at a constant height of h above the apex of the cone, what is the minimum value of coefficient static friction?
Part A Review The 50 kg ciroular lead piston shown in (Figure 1) floats on 0.21...

Part A Review The 50 kg ciroular lead piston shown in (Figure 1) floats on 0.21 mol of compressed air What is the piston height h if the temperature is 30 C Express your answer with the appropriate units. hValue Units Submit Request Answer Figure 1 of1 ▼PartB How far does the piston move the temperature is ncreased by 10007 Express your answer with the appropriate units 1 atm 0 kg Units 30℃ Submit Request Answer 10 cm

(a) Figure 2 shows a cuboid and a cone (not drawn to scale). Edge AB has...

(a) Figure 2 shows a cuboid and a cone (not drawn to scale). Edge AB has length 26 cm, and the diagonal AC has length 42 cm. The radius r of the cone is 12 cm, the height h is 16 cm and the slant height l is 20 cm. D 26 cm B 1= 20 cm h=16 cm 42 cm r= 12 cm Figure 2 Give your answers to each of the following to two significant figures. (1) Find...
QUESTION 3 Figure below indicated that a plug with cone shape used to plugged a hole...

QUESTION 3 Figure below indicated that a plug with cone shape used to plugged a hole of 45 cm radius at one side of a tank that containing X fluid (SG-0.8). The cone is 1.5 m height and I.I m bottom diameter. Depth of cone center point to the surface liquid is 10m. a) Draw the distribution of pressure onto the plug b) Determine the force acts onto the plug Cone 10 m QUESTION 4 Figure below shows a water...
Water flows through a pipe reducer as shown in the figure. If the manometer reading h - 2 m. Find...

Water flows through a pipe reducer as shown in the figure. If the manometer reading h - 2 m. Find the flow rate in Liters per second. Assume DI-15 cm, D2-10 cm. SG:-0.80 a. What is the effect of the angle θ b. Is this a practical arrangement, if yes why, if not how would you improve it? c. Ca n mercury be used as a manometer fluid in this arrangement? Why, or why not? SG D2 Water Di Water...

The device shown in Figure OA3 is called a cone-plate viscometer. The angle of the cone...

The device shown in Figure OA3 is called a cone-plate viscometer. The angle of the cone is very small, so that sin 0 0, and the gap is filled with the test liquid. The torque M to rotate the cone at the angular velocity Q is measured. Assuming a linear fluid velocity profile along the thickness of the fluid film and non-slip boundary condition at the surfaces of the solid bodies, derive an expression for fluid dynamic viscosity u as...