clear and neat please The acrylic plastic rod is 200 mm long and 15 mm in...
The acrylic plastic rod is 200 mm long and 20 mm in diameter. Part A If an axial load of 250 N is applied to it, determine the change in its length. EP-2.70 GPa, vp-0.4 (Figure 1) Express your answer with the appropriate units. Value Units Submit t Answer Part B Determine the change in its diameter. Express your answer with the appropriate units. Figure 1 of1 Ad# 1 Value Units Submit t Answer 200 mm Provide Feedback
The acrylic plastic rod is 200mm long and 15mm in diameter. If an axial load of 300N is applied to it, determine the change in its length and the change in its diameter. Ep = 2.70 GPa, Vp = 0.4.
Could someone help me with this problem? Thank you in advance! 4) The acrylic plastic rod is 200 mm long and 15 mm in diameter. If an axial load of 250 N is applied to it, determine the change in its length and the change in its diameter. Assume the elastic modulus, E, is 2.24 GPa, and the shear modulus, G, is 870 MPa. 250 N 250 N 200 mm
Q1. A circular rod of 12 mm diameter was tested for tension. The total elongation on a 300 mm length was 0.22 mm under a tensile load of 17 KN. Find the value of E. (2.5 Marks) Answer: Q2. A prismatic bar has a cross section of 25 mm x 50 mm and a length of 2m under an axial force of 90 KN. The measured elongation of the bar is 1.5 mm. Compute the tensile stress and strain in...
A 100-mm long rod has a diameter of 15 mm, Part A If an axial tensile load of 195 kN s applied, determine its change in length. Assume linear-elastic behavior with E = 200 GPa. Express your ahswer to three significant figures and include the appropriate units. ? Suomi Request Answer Provide Feedback
A 1.5-m-long aluminum rod must not stretch more than 1 mm and the normal stress must not exceed 40 MPa when the rod is subjected to a 3.0-kN axial load. Knowing that E= 70 GPa, determine the required diameter of the rod. The required diameter of the rod is mm.
roblem 1: The built-up shaft consists of a pipe AB and solid rod BC. Pipe AB has an inner diameter of 20 mm and outer diameter of 28 mm. The length of AB is 200 mm. Rod BC has a diameter of 12 mm and a length of 180 mm. (a) Determine the average normal stress at points D and E (b) If the modulus of elasticity of pipe AB is EAB-200 GPa, Poisson's ratio of rod BC is VBc...
6. A rod pof steel is l=12_ cm long and has a d= 0.6 mm diameter. A P= 16 kN load pulls on each end of the bar. Given the strain along the bar El= 0.03, and Poisson's ratio of v=0.21 : (20%) .. Р Р a) the stress exerted on the rod o? b) the modulus of elasticity, E? c) the elongation of the bar, Al? d) the strain along the lateral direction, Edia? e) the change of diameter...
Q-1 A solid circular rod with a diameter d = 18 mm is shown in Figure Q-3. The rod is made of an aluminum alloy that has an elastic modulus E = 72 GPa and a Poisson's ratio v=0.32. When subjected to the axial load P, the diameter of the rod decreases by 0.025 mm. For a factor of safety of 1.75, a) Determine the magnitude of the safe allowable load P. pts.] b) If we have a 12 mm...
Due to the operational conditions and temperature gradient, a 95 mm diameter, 1.75 m long steel rod within a machine assembly is subjected to a combination of tensile loading of 190 N and thermal loading which imposes a longitudinal force of 244 N. The total loading results in an even distribution of forces on the body of the rod causing it to change its dimensions by increasing 0.45 mm in length at both ends and decreasing by 0.0135 mm at...