Question

Question 9 (TCO 2) A _____ is similar to a print statement, but takes much less...

Question 9

(TCO 2) A _____ is similar to a print statement, but takes much less time to execute.

heartbeat

monitor

dump

profile

Question 10

(TCO 3) For the permanent magnet of the DC motor, we have _____.

one lead for + volt

two leads for + and –

four leads

eight leads

Question 11

(TCO 5) The voltage dropout of a voltage regulator is 1.6 V. If a 14 V output is required, what is the minimum regulator input voltage?

16 V

15.6 V

13.4 V

12.4 V

Question 12

(TCO 6) The C syntax for specifying a Timer Channel 3 subroutine is _____.

interrupt 11

interrupt 10

interrupt 12

interrupt 9

Question 13

(TCO 6) The TOF interrupt number is _____.

16

15

14

13

Question 14

(TCO 5) An H-bridge allows a 5 A current pulse to the drive motor. What is the average current if the duty cycle is 50% and the pulse frequency is 2 kHz?

1.25 A

2.5 A

10 A

2 A

Question 15

(TCO 4) A communications channel has a bandwidth of 2,000 Hz and a signal-to-noise ratio (SNR) of 40 dB. What is the maximum possible data rate?

11 kbits/sec

50 bits/sec

27 kbits/sec

80 kbits/sec

Question 16

(TCO 5) An H-bridge allows a 2.5 A current pulse to the drive motor. What is the average current if the duty cycle is 25% and the pulse frequency is 2 kHz?

0.625 A

4 A

10 A

2.5 A

0 0
Add a comment Improve this question Transcribed image text
Answer #1

Q9. Dump takes less time to execute than printf

Q10. Two for +ve and -ve

Q11. 15.6 should be the minimum input voltage.

Q12. Interrupt 9

Q13. 14 is the Timer Overflow interrupt

Q14.10 A

Q15. Data rate = bandwidth * log2(1+SNR) = 11Kbps

Q16. 2.5A

Add a comment
Know the answer?
Add Answer to:
Question 9 (TCO 2) A _____ is similar to a print statement, but takes much less...
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Not the answer you're looking for? Ask your own homework help question. Our experts will answer your question WITHIN MINUTES for Free.
Similar Homework Help Questions
  • TCO 2) For the circuit below, if Vcc is 28 volts and Rb is 4.7k ohms,...

    TCO 2) For the circuit below, if Vcc is 28 volts and Rb is 4.7k ohms, find the base and collector voltages and currents for an input of OV and 5V. Beta 300, the motor resistance is 400 ohms. AG1 NI MOTOR SERVO Vin N Yout Rb 1a: When Vin OV, find: lb = Ic = Vbase Vcol 1b: when Vin 5V, find: IC Vbase HTML Editor Question 6 7 pts TCO 1) Find the following for an input of...

  • *5. Design a BJT transistor drive circuit like the one shown Figure 10-7 (Hart's text) with an in...

    *5. Design a BJT transistor drive circuit like the one shown Figure 10-7 (Hart's text) with an initial peak base current, IB,-8 1B2, where 1B2 denotes the minimum base current required to drive the transistor to saturation. Assume a collector load resistance, Rc-8 Ω, collector supply voltage Vs = 30 V, large signal current of the transistor, hFE-min. 10, max. 20), VBE(on)-0.8 V, and the input is periodic pulse waveform (0 to 6) V, with a duty cycle, D-0.5. Also,...

  • DC-DC Converter Machine Drives D QUE D EA TI C+ ata at I A separately excited...

    DC-DC Converter Machine Drives D QUE D EA TI C+ ata at I A separately excited DC motor is powered by a full bridge power converter using MOSFET power transistors and freewheeling diodes as shown above, Converter: Vs - 250 V Switching frequency - 5 kHz. Two-quadrant mode: Q3 always open and Q4 always closed. Assume ideal switches and diodes. DC machine: R-50 m2 LA = 300 H Ex -0.2 V/(r/min) Ignore rotational losses and brush voltage drop Answer the...

  • *5. Design a BJT transistor drive circuit like the one shown Figure 10-7 (Hart's text) with...

    *5. Design a BJT transistor drive circuit like the one shown Figure 10-7 (Hart's text) with an initial peak base current, IB,-8 1B2, where 1B2 denotes the minimum base current required to drive the transistor to saturation. Assume a collector load resistance, Rc-8 Ω, collector supply voltage Vs = 30 V, large signal current of the transistor, hFE-min. 10, max. 20), VBE(on)-0.8 V, and the input is periodic pulse waveform (0 to 6) V, with a duty cycle, D-0.5. Also,...

  • Current Clamp Properties XFG2 NUN Ratio of voltage to current: 1 VA OK Cancel хса R2...

    Current Clamp Properties XFG2 NUN Ratio of voltage to current: 1 VA OK Cancel хса R2 OW- C1 Oscilloscope-XSC2 Current (A) Volts (V) Function generator-XFG2 Waveforms Sigal options Frequency: Duty cyde: Amplitude: Offset 50 ** 2.02 30.08 ms 20.075 10.01 Chama 61.623 my 1.560 V 1.499 V Channels LOSSY 09.08 my 48.733 Troger Edget DEB Timebase Channel A Scale: 10 ms.Ov S cale: 1 VW Xpos.) 14 . Yol.): O YA BA AB AC DC Figure 2. RC Circuit Channels...

  • I need help doing this D Question 11 7.5 pts If a PWM signal has a...

    I need help doing this D Question 11 7.5 pts If a PWM signal has a frequency of 100Hz and a duty cycle of 10%, how long is the output on before turning off? Provide your answer in ms. D Question 12 7.5 pts If a PWM signal has a frequency of 1000Hz and a duty cycle of 25%, how long is the output on before turning off? Provide your answer in ms. Question 13 10 pts If a PWM...

  • Objectives: To learn transient behavior of series RC circuits To observe of time constant and its...

    Objectives: To learn transient behavior of series RC circuits To observe of time constant and its effect on charging process of capacitor using pulse waveforms Equipment: Oscilloscope Function generator Resistors (1 k) Capacitors (1 uF) Breadboard Pre-Lab Questions A pulse is a voltage or current that changes from one level to the other and back again. If a waveform's high time equals its low time, it is called a square wave. The length of each cycle (one positive peak and...

  • O bructe CONFIDENTIAL 2 limitatio of Flyb Q2 (a) With the aid of respective topology, point...

    O bructe CONFIDENTIAL 2 limitatio of Flyb Q2 (a) With the aid of respective topology, point out three (3) basic de-de converters ( 3 marks) (b) Discuss the energy transfer in on each circuit by refering the circuits drawn in Q2(a) (3 marks) (c) Design a boost converter for continuous inductor current and an output nipple voltage of less than 1% that will have an output of 30 V from a 12 V source, Assume the load resistance of 50...

  • O bructe CONFIDENTIAL 2 limitatio of Flyb Q2 (a) With the aid of respective topology, point...

    O bructe CONFIDENTIAL 2 limitatio of Flyb Q2 (a) With the aid of respective topology, point out three (3) basic de-de converters ( 3 marks) (b) Discuss the energy transfer in on each circuit by refering the circuits drawn in Q2(a) (3 marks) (c) Design a boost converter for continuous inductor current and an output nipple voltage of less than 1% that will have an output of 30 V from a 12 V source, Assume the load resistance of 50...

  • ****Please ALL answers questions with complete steps.**** 1. Analysis and design of a buck-boost converter. A...

    ****Please ALL answers questions with complete steps.**** 1. Analysis and design of a buck-boost converter. A buck-boost converter is illustrated below. + licit) + reee c= R { v(t) A practical implementation using a MOSFET and diode is illustrated below. D + Voi(t) – H + iqi(t) IT int) lic(t) iz(t) + LE vi(t) c R v(t) For this problem, you must employ the methods of inductor volt-second balance, capacitor charge balance, and the small ripple approximation as discussed in...

ADVERTISEMENT
Free Homework Help App
Download From Google Play
Scan Your Homework
to Get Instant Free Answers
Need Online Homework Help?
Ask a Question
Get Answers For Free
Most questions answered within 3 hours.
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT