Homework Answers
Add Answer to:
2. A heated flat plate 1.0 m long (in the direction of flow) and 0.5 m...
A flat plate test section, designed for a boundary-layer measurement experiment, is 0.5 m wide an...
A flat plate test section, designed for a boundary-layer
measurement experiment, is 0.5 m wide and has an electrically
heated surface installed 0.5 m away from the leading edge (see
figure below). The electrically heated strip is 10 cm long and 5mm
deep. It is insulated at its bottom surface as well as both
wide-end edges. If the surface of this electrical heater strip is
to be maintained at a uniform temperature of 120°C when the
atmospheric pressure air at...
Water at 10 degrees Celsius and a velocity of 2.5 m/s is flowing along a 4.5 m long flat plate at a uniform temperature of 40 degrees Celsius. If the plate is 1.5 m wide, determine: a) the distance fr...
Water at 10 degrees Celsius and a velocity of 2.5 m/s is flowing along a 4.5 m long flat plate at a uniform temperature of 40 degrees Celsius. If the plate is 1.5 m wide, determine: a) the distance from the leading edge of the plate where the flow becomes turbulent, b) the heat transfer rate between the plate and the flowing water, c) the fraction of the force exerted by the water on the first half of the plate...
Air at a temperature of 300 K flows over one side of a flat plate of...
Air at a temperature of 300 K flows over one side of a flat plate of width 1 m at a velocity of 20 m/s. The plate has a constant surface temperature of 350 K. Assume Re(x,c)=5x10^5. a) What is the velocity boundary layer thickness at the end of the plate if L=0.25 m? What if L=1 m? b) Calculate the drag on the plate if L=0.25 m. What is the drag if L=1 m? c) Find the heat transfer...
Air at 20 °C and 1 atm. flow over a flat plate with 35 m/s. The...
Air at 20 °C and 1 atm. flow over a flat plate with 35 m/s. The size of the plate is 75 cm by 75 cm and is maintained at 60 °C. Calculate: a) The heat transfer rate 40 cm from the leading edge of the plate. b) The heat transfer rate at the end of the plate (at x = L). c) The heat transfer rate from the entire plate. d) The heat transfer rate at the...
8) Air flows over a flat plate at a velocity of 20 m/s and a temperature...
8) Air flows over a flat plate at a velocity of 20 m/s and a temperature of 20C. The surface temperature of the plate is 134C, and the length of the plate in the direction of flow is 1.5 m. Properties of air may be taken as A-0.030 W/m-C, Pr-0.700, and a/p 2.092E-5 m/s (5% ) What is the location from the leading edge, X, where the flow becomes turbulent Re (20)15 a l Ve30s T20 T LaLS 523 m...
Problem 1: Atmospheric air at 25°C flows over both surfaces of 2 m long flat plate...
Problem 1: Atmospheric air at 25°C flows over both surfaces of 2 m long flat plate maintained at 125°C. For upper surface, velocity of air is 1 m/s and for lower surface, velocity is 10 m/s. (Rex,c = 5x105) (a) Determine the flow condition for upper and lower surfaces. (Laminar, or turbulent). If the condition is that laminar to turbulent is taking place, calculate the position where transition from the laminar to turbulent happens. (b) Determine the rate of heat...
A 5 m long x 1m wide horizontal plate is heated on top and insulated on...
A 5 m long x 1m wide horizontal plate is heated on top and insulated on the bottom. The plate is maintained at 200 C. The air and walls of the room are maintaine d at 25°C. Determine the heat transfer by nature convection and radiation heat transfer. Assume an emissivity of 0.8.
2. (25 pts) Engine oil flows with a velocity of 6 m/s over a flat plate...
2. (25 pts) Engine oil flows with a velocity of 6 m/s over a flat plate having 1m length and 1 m width. The oil has a free stream temperature To= 80 °C and the plate surface temperature is maintained at Ts = 0 °C. a. Determine whether the flow over the plate transitions to turbulent regime. b. Calculate the average friction factor and the average heat transfer coefficient for the plate by using the appropriate correlations. c. Calculate the...
For laminar flow over a flat plate, the local heat transfer coefficient hx =x-1/2 where x...
For laminar flow over a flat plate, the local heat transfer coefficient hx =x-1/2 where x is the distance from the leading edge (x-0) of the plate. What is the average heat transfer coefficient from the leading edge to location x
Required information Air at 25°C and 1 atm is flowing over a long flat plate with...
Required information Air at 25°C and 1 atm is flowing over a long flat plate with a velocity of 7 m/s. The density and kinematic viscosity of air at 1 atm and 25°C are p= 1.184 kg/m3 and V = 1.562x10-5 m2/s. Calculate the distance from the leading edge of the plate where the flow becomes turbulent. The distance from the leading edge of the plate is m. Required information Air at 25°C and 1 atm is flowing over a...
A flat plate test section, designed for a boundary-layer
measurement experiment, is 0.5 m wide and has an electrically
heated surface installed 0.5 m away from the leading edge (see
figure below). The electrically heated strip is 10 cm long and 5mm
deep. It is insulated at its bottom surface as well as both
wide-end edges. If the surface of this electrical heater strip is
to be maintained at a uniform temperature of 120°C when the
atmospheric pressure air at...
8) Air flows over a flat plate at a velocity of 20 m/s and a temperature of 20C. The surface temperature of the plate is 134C, and the length of the plate in the direction of flow is 1.5 m. Properties of air may be taken as A-0.030 W/m-C, Pr-0.700, and a/p 2.092E-5 m/s (5% ) What is the location from the leading edge, X, where the flow becomes turbulent Re (20)15 a l Ve30s T20 T LaLS 523 m...
Problem 1: Atmospheric air at 25°C flows over both surfaces of 2 m long flat plate maintained at 125°C. For upper surface, velocity of air is 1 m/s and for lower surface, velocity is 10 m/s. (Rex,c = 5x105) (a) Determine the flow condition for upper and lower surfaces. (Laminar, or turbulent). If the condition is that laminar to turbulent is taking place, calculate the position where transition from the laminar to turbulent happens. (b) Determine the rate of heat...
A 5 m long x 1m wide horizontal plate is heated on top and insulated on the bottom. The plate is maintained at 200 C. The air and walls of the room are maintaine d at 25°C. Determine the heat transfer by nature convection and radiation heat transfer. Assume an emissivity of 0.8.
2. (25 pts) Engine oil flows with a velocity of 6 m/s over a flat plate having 1m length and 1 m width. The oil has a free stream temperature To= 80 °C and the plate surface temperature is maintained at Ts = 0 °C. a. Determine whether the flow over the plate transitions to turbulent regime. b. Calculate the average friction factor and the average heat transfer coefficient for the plate by using the appropriate correlations. c. Calculate the...
For laminar flow over a flat plate, the local heat transfer coefficient hx =x-1/2 where x is the distance from the leading edge (x-0) of the plate. What is the average heat transfer coefficient from the leading edge to location x
Required information Air at 25°C and 1 atm is flowing over a long flat plate with a velocity of 7 m/s. The density and kinematic viscosity of air at 1 atm and 25°C are p= 1.184 kg/m3 and V = 1.562x10-5 m2/s. Calculate the distance from the leading edge of the plate where the flow becomes turbulent. The distance from the leading edge of the plate is m. Required information Air at 25°C and 1 atm is flowing over a...
Most questions answered within 3 hours.
-
Discuss the pros and cons of collaborative software such
as SameTime. Does it increase productivity? What...
asked 1 minute ago -
A large cable company reports the following.
80% of its customers subscribe to its cable TV...
asked 3 minutes ago -
Buying your in-laws a gift because it’s expected is
due to the ____________ motive of gift-giving....
asked 4 minutes ago -
Calculate the expected value, the variance, and the standard
deviation of the given random variable X....
asked 47 minutes ago -
A hospital performs 100 surgeries per week. The probability that
complications after surgery occur is 10%....
asked 1 hour ago -
1 point) Given the significance level α=0.01 find the following:
(a) left-tailed z value z= (b)...
asked 45 minutes ago -
Assuming you are the head of the software development unit at
Cyber.Soft, explain and justify why...
asked 11 minutes ago -
Magnesium and nitrogen react in a combination reaction to
produce magnesium nitride. 3 Mg + N2...
asked 19 minutes ago -
Two electrons are initially at rest separated by a distance of
2nm. At time t=0, they...
asked 17 minutes ago -
A martial artist is practicing breaking 5 boards. He is able to
break aboard with probability...
asked 24 minutes ago -
The rate constant of a first-order reaction is 2.95 × 10−4 s−1
at 350.° C. If...
asked 27 minutes ago -
implement a class called PiggyBank that will be used to
represent a collection of coins. Functionality...
asked 19 minutes ago