A flat plate test section, designed for a boundary-layer measurement experiment, is 0.5 m wide and has an electrically heated surface installed 0.5 m away from the leading edge (see figure below). The electrically heated strip is 10 cm long and 5mm deep. It is insulated at its bottom surface as well as both wide-end edges. If the surface of this electrical heater strip is to be maintained at a uniform temperature of 120°C when the atmospheric pressure air at 20°C flows over it at 20 m/s, estimate the rate of heat generation necessary in the heated strip in order to maintain its surface temperature uniformly.
Homework Answers
Add Answer to:
A flat plate test section, designed for a boundary-layer measurement experiment, is 0.5 m wide an...
2. A heated flat plate 1.0 m long (in the direction of flow) and 0.5 m...
2. A heated flat plate 1.0 m long (in the direction of flow) and 0.5 m wide is maintained at a constant temperature of 100°C. Cooling water at a temperature of 24°C flows over the top of the plate at 15 cm/s. Assume the bottom of the plate is adiabatic. a. Determine the heat transfer rate from the plate. b. A trip wire is placed at the leading edge of the plate, tripping the flow to turbulent. Determine the heat...
Problem 2 (50 Points A flat, isothermal vertical heating panel, 0.5 m wide by 1 m...
Problem 2 (50 Points A flat, isothermal vertical heating panel, 0.5 m wide by 1 m high is mounted inside a large room. The surface of the panel has an emissivity of 0.90 and is maintained at 400 K If the walls and air of the room are at 300 K, calculate: a) The Rayleigh number of the free convection boundary layer. b) Selecting a suitable equation for Nusselt number, calculate the heat transfer coefficient of the flow c) The...
Supplemental Problem 7.001 A flat plate of width 1 m is maintained at a uniform surface temperatu...
Supplemental Problem 7.001 A flat plate of width 1 m is maintained at a uniform surface temperature of Ts = 160°C by using independently of thickness a 12 mm and length b 50 mm. plate at a velocity of 30 m/s. The thermophysical properties of the module are k Reynolds number is 5x105 rectangular modules Each module is insulated from its neighbors, as well as on its back side. Atmospheric air at 25%C flows over the 5.2 w/m-K, cp320 J/kg...
PRINTER VERSION BACK NEXT RCES Supplemental Problem 7.001 A flat plate of width 1 m is...
PRINTER VERSION BACK NEXT RCES Supplemental Problem 7.001 A flat plate of width 1 m is maintained at a uniform surface temperature of T,-160°C by using independently controlled, heat-generating rectangular modules of thickness a 10 mm and length b 50 mm. Each module is insulated from its neighbors, as well as on its back side. Atmospheric air at 25°C flows over the plate at a velocity of 30 m/s. The thermophysical properties of the module are k5.2 W/m K, cp...
Please answet the the questions in detail it belong to Heat and Mass transfer Question2 Marks...
Please answet the the questions in detail it belong to
Heat and Mass transfer
Question2 Marks 191 In the context of a finite difference scheme for a material of thermal conductivity k, use an energy balance to derive the nodal equation for an extemal side node (illustrated) which is: heated by an electrical heater (generating surface heat flux q, W/m), .and cooled by convection (of heat transfer Tm+1,n coefficient h, W/m'K) into an ambient of air temperature T mn A...
Your Initials ). Convection external flow An array of silicon chips, each of length L 10 mm and width w 10 mm on a side, is insulated on one surface and cooled on the opposite surface by atmospheric...
Your Initials ). Convection external flow An array of silicon chips, each of length L 10 mm and width w 10 mm on a side, is insulated on one surface and cooled on the opposite surface by atmospheric air in parallel flow with T. 24 C and u40 m/s. When in use, the same electrical power is dissipated in each chip, maintaining a uniform heat flux over the entire cooled surface. Assume properties for air are v 184 10 m...
The roof of a minivan can be approximated as a flat plate, 2-m wide and 3.5-m...
The roof of a minivan can be approximated as a flat plate, 2-m wide and 3.5-m long. The sun beats down on the roof such that the net solar radiation absorbed is 350 W/m2. If the ambient air is 32 °C. the car is moving at 100 km/hr, and the inside surface of the roof is heavily insulated, determine the steady-state temperature of the roof (in °C). Ignore radiation emitted from the roof. T32°C T 350w Assuming T, *45oC. Tlm-32+45)/2...
Please help to answer all sections. please also write neatly and clearly , i got a...
Please help to answer all sections. please also write neatly
and clearly , i got a hard time reading curvsy
handwriting.thanks
Question 3 A fish tank in a house has the following internal dimensions: it is 75 cm long, 30 cm wide and 35 cm deep. It is made of glass 4 mm thick and is filled with water to the top. Both its top and its bottom are sufficiently well insulated that it can be assumed that no heat...
Two large parallel plates with surface conditions approximating those of a blackbody are maintained at 800°C...
Two large parallel plates with surface conditions approximating those of a blackbody are maintained at 800°C and 100°C, respectively. Determine the rate of heal transfer by radiation between the plates in Wim and the radiative heat transfer coefficient in W/m K ) 12 Write down the one-dimensional sent heal conduction equation for a plane wall with constant thermal conductivity and heat generation in its simplest form, and indicate what each variable represents 13 Write down the one-dimensional transient heat conduction...
IF YOU CANNOT SOLVE THEM ALL THEN PLEASE DONT SOLVE ANY. A hollow aluminum sphere, with...
IF YOU CANNOT SOLVE THEM ALL THEN PLEASE DONT SOLVE ANY.
A hollow aluminum sphere, with an electrical heater in the center, is used in tests to determine the thermal conductivity of insulating materials. The inner and outer radii of the sphere are 0.15 and 0.18 m, respectively, and testing is done under steady-state conditions with the inner surface of the aluminum maintained at 250°C. In a particular test, a spherical shell of insulation is cast on the outer surface...
2. A heated flat plate 1.0 m long (in the direction of flow) and 0.5 m wide is maintained at a constant temperature of 100°C. Cooling water at a temperature of 24°C flows over the top of the plate at 15 cm/s. Assume the bottom of the plate is adiabatic. a. Determine the heat transfer rate from the plate. b. A trip wire is placed at the leading edge of the plate, tripping the flow to turbulent. Determine the heat...
Problem 2 (50 Points A flat, isothermal vertical heating panel, 0.5 m wide by 1 m high is mounted inside a large room. The surface of the panel has an emissivity of 0.90 and is maintained at 400 K If the walls and air of the room are at 300 K, calculate: a) The Rayleigh number of the free convection boundary layer. b) Selecting a suitable equation for Nusselt number, calculate the heat transfer coefficient of the flow c) The...
Supplemental Problem 7.001 A flat plate of width 1 m is maintained at a uniform surface temperature of Ts = 160°C by using independently of thickness a 12 mm and length b 50 mm. plate at a velocity of 30 m/s. The thermophysical properties of the module are k Reynolds number is 5x105 rectangular modules Each module is insulated from its neighbors, as well as on its back side. Atmospheric air at 25%C flows over the 5.2 w/m-K, cp320 J/kg...
PRINTER VERSION BACK NEXT RCES Supplemental Problem 7.001 A flat plate of width 1 m is maintained at a uniform surface temperature of T,-160°C by using independently controlled, heat-generating rectangular modules of thickness a 10 mm and length b 50 mm. Each module is insulated from its neighbors, as well as on its back side. Atmospheric air at 25°C flows over the plate at a velocity of 30 m/s. The thermophysical properties of the module are k5.2 W/m K, cp...
Please answet the the questions in detail it belong to
Heat and Mass transfer
Question2 Marks 191 In the context of a finite difference scheme for a material of thermal conductivity k, use an energy balance to derive the nodal equation for an extemal side node (illustrated) which is: heated by an electrical heater (generating surface heat flux q, W/m), .and cooled by convection (of heat transfer Tm+1,n coefficient h, W/m'K) into an ambient of air temperature T mn A...
Your Initials ). Convection external flow An array of silicon chips, each of length L 10 mm and width w 10 mm on a side, is insulated on one surface and cooled on the opposite surface by atmospheric air in parallel flow with T. 24 C and u40 m/s. When in use, the same electrical power is dissipated in each chip, maintaining a uniform heat flux over the entire cooled surface. Assume properties for air are v 184 10 m...
The roof of a minivan can be approximated as a flat plate, 2-m wide and 3.5-m long. The sun beats down on the roof such that the net solar radiation absorbed is 350 W/m2. If the ambient air is 32 °C. the car is moving at 100 km/hr, and the inside surface of the roof is heavily insulated, determine the steady-state temperature of the roof (in °C). Ignore radiation emitted from the roof. T32°C T 350w Assuming T, *45oC. Tlm-32+45)/2...
Please help to answer all sections. please also write neatly
and clearly , i got a hard time reading curvsy
handwriting.thanks
Question 3 A fish tank in a house has the following internal dimensions: it is 75 cm long, 30 cm wide and 35 cm deep. It is made of glass 4 mm thick and is filled with water to the top. Both its top and its bottom are sufficiently well insulated that it can be assumed that no heat...
Two large parallel plates with surface conditions approximating those of a blackbody are maintained at 800°C and 100°C, respectively. Determine the rate of heal transfer by radiation between the plates in Wim and the radiative heat transfer coefficient in W/m K ) 12 Write down the one-dimensional sent heal conduction equation for a plane wall with constant thermal conductivity and heat generation in its simplest form, and indicate what each variable represents 13 Write down the one-dimensional transient heat conduction...
IF YOU CANNOT SOLVE THEM ALL THEN PLEASE DONT SOLVE ANY.
A hollow aluminum sphere, with an electrical heater in the center, is used in tests to determine the thermal conductivity of insulating materials. The inner and outer radii of the sphere are 0.15 and 0.18 m, respectively, and testing is done under steady-state conditions with the inner surface of the aluminum maintained at 250°C. In a particular test, a spherical shell of insulation is cast on the outer surface...
Most questions answered within 3 hours.
-
In risk management, insurance is an example of:
Select one:
a. Risk avoidance
b. Risk deflection...
asked 4 minutes ago -
Write the equilibrium expression for the dissociation in
water for CH5N, C2H5O2COOH, H3AsO4, KClO2, HC2H2ClO2.
asked 2 minutes ago -
Wildhorse Company follows the practice of pricing its inventory
at the lower-of-cost-or-market, on an individual-item
basis....
asked 38 minutes ago -
3. (10 pts) You grow a corn crop that yields 150 bushels ac-1,
with the following...
asked 27 minutes ago -
7. The term Six Sigma refers to:
Select one:
a. The control limits established in a...
asked 36 minutes ago -
For the following reaction: A(g) + 2 B(g) ⇌ 2 C(g) Calculate the
equilibrium constant K...
asked 39 minutes ago -
Which of the following best describes tidal volume? options:
1.The amount of oxygen in the air...
asked 55 minutes ago -
1. Smaller cost distortions occur when the traditional systems'
single indirect-cost rate and the activity-cost-driver rates:...
asked 1 hour ago -
Using either a FMECA approach or some other appropriate RCA
tool, identify five risk treatment actions...
asked 1 hour ago -
If for a test the P-value is between 0.0025 and 0.005, what
conclusion can you draw?...
asked 1 hour ago -
Using Python. Write a function clean2(aList) that takes a list
of integers aList as argument, and...
asked 1 hour ago -
Intrapreneurship is defined as the
development of an enterprise culture with an existing (Nandan,
2009). An...
asked 1 hour ago