Homework Answers
Add Answer to:
QUESTION 3 Using the data below, determine the bending factor of safety for the pinion. Gear...
There are two spur gears in mate (a pinion and gear) determine the minimum face width...
There are two spur gears in mate (a pinion and gear) determine the minimum face width based on the bending equations and the data below: (hint: use iterative approach) . Determine the face-width for the pinion (use bending equations) * Design/Safety Factor (SF) 2 · NP (teeth) = 20 Pressure angle (degrees) = 20 · n (rpms) = 1200 H (hp) 100 Ng (teeth) = 60 . Pd (teeth/in) 8 . Quality number (Qv) 11 Pinion is made of nitrided...
There are two bevel gears in mate (a pinion and gear) determine the maximum diametral pitch...
There are two bevel gears in mate (a pinion and gear) determine the maximum diametral pitch (or closest to SF) based on the bending equations and the data below: (hint: use iterative approach, meaning it make take more than one try) (Also recall that diametral pitches are standardized, find the one the closest to standardized value while satisfying the FOS) . Determine the optimal diametral pitch, P, for the pinion (use bending equations) . Design/Safety Factor (SF)2.00 Overall Factor of...
Gear Design- Data for problems A pair of steel full-depth, involute teeth, the pinion speed is...
Gear Design- Data for problems A pair of steel full-depth, involute teeth, the pinion speed is 1000 rpm. The pinion has 18 teeth and the gear has 36 teeth. The gears have a quality grade of A8, a design reliability of 99% with a factor of safety of 1.0. They are installed in a commercial enclosed gear unit. The pinion has a rim thick gears transmits an average of 10 hp. The gear pair has a P 8, a 20...
12. [25 points] A grade-2 through-hardened steel pinion with BHN of 350 is driving a steel...
12. [25 points] A grade-2 through-hardened steel pinion with BHN of 350 is driving a steel gear of the same material and hardness. The diameteral pitch is 10, the number of teeth on pinion is 18, the face width is 0.95 inch, and the pressure angle of the full-depth teeth is 20 degrees The input (pinion) rpm is 2000 and the output rpm is 500. The gears transmit 5 horsepower. The gearbox precision corresponds to "commercial enclosed gear units". Determine...
designs QIII) A 15-tooth, precision-made spur pinion is to drive a 25-tooth gear. A pitch of...
designs
QIII) A 15-tooth, precision-made spur pinion is to drive a 25-tooth gear. A pitch of 6 teeth/in has been selected with a 2.25 in face width. Also, the teeth are to be 25 full depth, with a ddendum of 1.35/ pa for a pinion speed of 1150 rpm, and 10 hp is to transmitted under steady load conditions. The material selected for both gears is a through-hardened steel of a hardness of 302 Bhn . Determined the actors of...
The Isthmus Slough drawbridge has an open gear reduction for the span drive. A mating pair...
The Isthmus Slough drawbridge has an open gear reduction for the span drive. A mating pair of gears pinion E and gear Fare located about mid-way in the 5 part speed reduction. The gear teeth are un- crowned open spur gears with a pressure angle o = 20 degrees. Both gears are made to an AGMA quality level Qv = 9 and have a measured hardness of HB = 183 made from through hardened Grade 1 Steel and are un-lapped....
9. AGMA Shigley 5th Ed. 14-27 A 17-tooth 20°-pressure angle spur pinion rotates at 1800 rev/min...
9. AGMA Shigley 5th Ed. 14-27 A 17-tooth 20°-pressure angle spur pinion rotates at 1800 rev/min and transmits 4 hp to a 52-tooth gear. The diametral pitch is 10, the face width is 1.25 in, the quality standard is No. 6, and the mounting is with exceptional rigidity. The pinion is steel, hardened to Brinell 240, and the gear is of No. 30 cast iron. Find the factor of safety based on surface fatigue strength if the life is to...
3. A commercial enclosed gear drive consists of a 20 spur pinion having 16 teeth driving a 48-tooth gear. The pinion speed is 300 rev/min, the gear face width 2 in., and the diametral pitch 6 teeth/i...
3. A commercial enclosed gear drive consists of a 20 spur pinion having 16 teeth driving a 48-tooth gear. The pinion speed is 300 rev/min, the gear face width 2 in., and the diametral pitch 6 teeth/in. The gears are grade t steel, through-hardened at 200 Brinell, made to No. 6 quality standards, uncrowned, and are to be accurately and ngid mounted Assume a lion life ofi will transmitareliability of90%(KR 0.85), and use YN 1.355N 01:8 and Z 1. used...
Component design Spur gear analysis A speed-reducer has 200 full-depth teeth, and the single reduction spur-gear...
Component design
Spur gear analysis
A speed-reducer has 200 full-depth teeth, and the single reduction spur-gear gearset has 22 and 60 teeth. The diametral pitch is 4 teeth/in and the face width is 3-1/4 in. The pinion shaft speed is 1145 rpm. The life goal of 5 year 24 hours per day service is about 3(10 9) pinion revolutions. The absolute value of the pitch variation is such that the transmission accuracy level number is 9. The materials are 4340...
7) [30 pts] Factor of Safety for Contact Stress A steel spur pinion has 16 teeth...
7) [30 pts] Factor of Safety for Contact Stress A steel spur pinion has 16 teeth cut on the 20 full-depth system with a module of 8 mm and a face width of 90 mm. The pinion rotates at 150 rev/min and transmits 3 kW to the mating steel gear. This pinion is to mesh with a steel gear with a gear ratio of 4:1. The Brinell hardness of the teeth is 200, and the tangential load transmitted by the...
There are two spur gears in mate (a pinion and gear) determine the minimum face width based on the bending equations and the data below: (hint: use iterative approach) . Determine the face-width for the pinion (use bending equations) * Design/Safety Factor (SF) 2 · NP (teeth) = 20 Pressure angle (degrees) = 20 · n (rpms) = 1200 H (hp) 100 Ng (teeth) = 60 . Pd (teeth/in) 8 . Quality number (Qv) 11 Pinion is made of nitrided...
There are two bevel gears in mate (a pinion and gear) determine the maximum diametral pitch (or closest to SF) based on the bending equations and the data below: (hint: use iterative approach, meaning it make take more than one try) (Also recall that diametral pitches are standardized, find the one the closest to standardized value while satisfying the FOS) . Determine the optimal diametral pitch, P, for the pinion (use bending equations) . Design/Safety Factor (SF)2.00 Overall Factor of...
Gear Design- Data for problems A pair of steel full-depth, involute teeth, the pinion speed is 1000 rpm. The pinion has 18 teeth and the gear has 36 teeth. The gears have a quality grade of A8, a design reliability of 99% with a factor of safety of 1.0. They are installed in a commercial enclosed gear unit. The pinion has a rim thick gears transmits an average of 10 hp. The gear pair has a P 8, a 20...
12. [25 points] A grade-2 through-hardened steel pinion with BHN of 350 is driving a steel gear of the same material and hardness. The diameteral pitch is 10, the number of teeth on pinion is 18, the face width is 0.95 inch, and the pressure angle of the full-depth teeth is 20 degrees The input (pinion) rpm is 2000 and the output rpm is 500. The gears transmit 5 horsepower. The gearbox precision corresponds to "commercial enclosed gear units". Determine...
designs
QIII) A 15-tooth, precision-made spur pinion is to drive a 25-tooth gear. A pitch of 6 teeth/in has been selected with a 2.25 in face width. Also, the teeth are to be 25 full depth, with a ddendum of 1.35/ pa for a pinion speed of 1150 rpm, and 10 hp is to transmitted under steady load conditions. The material selected for both gears is a through-hardened steel of a hardness of 302 Bhn . Determined the actors of...
The Isthmus Slough drawbridge has an open gear reduction for the span drive. A mating pair of gears pinion E and gear Fare located about mid-way in the 5 part speed reduction. The gear teeth are un- crowned open spur gears with a pressure angle o = 20 degrees. Both gears are made to an AGMA quality level Qv = 9 and have a measured hardness of HB = 183 made from through hardened Grade 1 Steel and are un-lapped....
9. AGMA Shigley 5th Ed. 14-27 A 17-tooth 20°-pressure angle spur pinion rotates at 1800 rev/min and transmits 4 hp to a 52-tooth gear. The diametral pitch is 10, the face width is 1.25 in, the quality standard is No. 6, and the mounting is with exceptional rigidity. The pinion is steel, hardened to Brinell 240, and the gear is of No. 30 cast iron. Find the factor of safety based on surface fatigue strength if the life is to...
3. A commercial enclosed gear drive consists of a 20 spur pinion having 16 teeth driving a 48-tooth gear. The pinion speed is 300 rev/min, the gear face width 2 in., and the diametral pitch 6 teeth/in. The gears are grade t steel, through-hardened at 200 Brinell, made to No. 6 quality standards, uncrowned, and are to be accurately and ngid mounted Assume a lion life ofi will transmitareliability of90%(KR 0.85), and use YN 1.355N 01:8 and Z 1. used...
Component design
Spur gear analysis
A speed-reducer has 200 full-depth teeth, and the single reduction spur-gear gearset has 22 and 60 teeth. The diametral pitch is 4 teeth/in and the face width is 3-1/4 in. The pinion shaft speed is 1145 rpm. The life goal of 5 year 24 hours per day service is about 3(10 9) pinion revolutions. The absolute value of the pitch variation is such that the transmission accuracy level number is 9. The materials are 4340...
7) [30 pts] Factor of Safety for Contact Stress A steel spur pinion has 16 teeth cut on the 20 full-depth system with a module of 8 mm and a face width of 90 mm. The pinion rotates at 150 rev/min and transmits 3 kW to the mating steel gear. This pinion is to mesh with a steel gear with a gear ratio of 4:1. The Brinell hardness of the teeth is 200, and the tangential load transmitted by the...
Most questions answered within 3 hours.
-
A certain rifle bullet has a mass of 5.25 g. Calculate the de
Broglie wavelength of...
asked 19 minutes ago -
Research new software products that assist in project
communication management. Write a paper summarizing your findings,...
asked 17 minutes ago -
the figure below to the left shows a beaker completely filled
with water. then a block...
asked 15 minutes ago -
what is the duistribution channels of HUL in india and how they
distribute?
how is this...
asked 22 minutes ago -
Batteries play an important role in our everyday lives. From
making many devices mobile, to allowing...
asked 34 minutes ago -
It is possible to iterate through an array quickly and easily
using a loop?
asked 42 minutes ago -
Determine the pHpH of an HFHF solution of each of the following
concentrations. The KAKA value...
asked 38 minutes ago -
Two point charges of 7.0mL are initially 11.5m apart. What is
the change in potential energy...
asked 39 minutes ago -
Please write as a short answer
You have heartburn and a two hour working session on...
asked 43 minutes ago -
Please solve with excel and mention the excel function.
Thanks
Kevin deposits $10,000 in a savings...
asked 45 minutes ago -
Which Special Journal would the following transaction be
journalized in?
Sold merchandise on account to Customer...
asked 57 minutes ago -
Assuming 100% dissociation, calculate the freezing point (?fTf)
and boiling point (?bTb) of 1.45 ? K3PO4(aq)1.45...
asked 59 minutes ago