Homework Answers
Add Answer to:
There are two spur gears in mate (a pinion and gear) determine the minimum face width...
There are two bevel gears in mate (a pinion and gear) determine the maximum diametral pitch...
There are two bevel gears in mate (a pinion and gear) determine the maximum diametral pitch (or closest to SF) based on the bending equations and the data below: (hint: use iterative approach, meaning it make take more than one try) (Also recall that diametral pitches are standardized, find the one the closest to standardized value while satisfying the FOS) . Determine the optimal diametral pitch, P, for the pinion (use bending equations) . Design/Safety Factor (SF)2.00 Overall Factor of...
QUESTION 3 Using the data below, determine the bending factor of safety for the pinion. Gear...
QUESTION 3 Using the data below, determine the bending factor of safety for the pinion. Gear type: Spur Gear with Full depth teeth . Pressure angle (degrees) 20 . Np (teeth) 20 * n (rpms) 1200 ·H(hp) = 60 . Ng (teeth) 36 Pd (teeth/in) 4 face width (in) 3 . Quality factor (Q ) = 8 e gear mounting straddled between bearings Pinion (HB) 300 (material: steel) Gear (HB) = 240 (material: steel) . Are the teeth crowned? No...
3. A commercial enclosed gear drive consists of a 20 spur pinion having 16 teeth driving a 48-tooth gear. The pinion speed is 300 rev/min, the gear face width 2 in., and the diametral pitch 6 teeth/i...
3. A commercial enclosed gear drive consists of a 20 spur pinion having 16 teeth driving a 48-tooth gear. The pinion speed is 300 rev/min, the gear face width 2 in., and the diametral pitch 6 teeth/in. The gears are grade t steel, through-hardened at 200 Brinell, made to No. 6 quality standards, uncrowned, and are to be accurately and ngid mounted Assume a lion life ofi will transmitareliability of90%(KR 0.85), and use YN 1.355N 01:8 and Z 1. used...
The Isthmus Slough drawbridge has an open gear reduction for the span drive. A mating pair...
The Isthmus Slough drawbridge has an open gear reduction for the span drive. A mating pair of gears pinion E and gear Fare located about mid-way in the 5 part speed reduction. The gear teeth are un- crowned open spur gears with a pressure angle o = 20 degrees. Both gears are made to an AGMA quality level Qv = 9 and have a measured hardness of HB = 183 made from through hardened Grade 1 Steel and are un-lapped....
designs QIII) A 15-tooth, precision-made spur pinion is to drive a 25-tooth gear. A pitch of...
designs
QIII) A 15-tooth, precision-made spur pinion is to drive a 25-tooth gear. A pitch of 6 teeth/in has been selected with a 2.25 in face width. Also, the teeth are to be 25 full depth, with a ddendum of 1.35/ pa for a pinion speed of 1150 rpm, and 10 hp is to transmitted under steady load conditions. The material selected for both gears is a through-hardened steel of a hardness of 302 Bhn . Determined the actors of...
Component design Spur gear analysis A speed-reducer has 200 full-depth teeth, and the single reduction spur-gear...
Component design
Spur gear analysis
A speed-reducer has 200 full-depth teeth, and the single reduction spur-gear gearset has 22 and 60 teeth. The diametral pitch is 4 teeth/in and the face width is 3-1/4 in. The pinion shaft speed is 1145 rpm. The life goal of 5 year 24 hours per day service is about 3(10 9) pinion revolutions. The absolute value of the pitch variation is such that the transmission accuracy level number is 9. The materials are 4340...
6) [20 pts) Bending Stress in a Gear A steel spur pinion has a pitch of...
6) [20 pts) Bending Stress in a Gear A steel spur pinion has a pitch of 6 teeth/in, 22 full-depth teeth with a cut profile, and a 20° pressure angle. The pinion runs at a speed of 1280 rev/min and transmits 15 hp to a 60-tooth gear. If the face width is 2 in., estimate the bending stress. Take the value of Lewis form factor, Y, from the table 14-2. The bending stress is kpsi.
7) [30 pts] Factor of Safety for Contact Stress A steel spur pinion has 16 teeth...
7) [30 pts] Factor of Safety for Contact Stress A steel spur pinion has 16 teeth cut on the 20 full-depth system with a module of 8 mm and a face width of 90 mm. The pinion rotates at 150 rev/min and transmits 3 kW to the mating steel gear. This pinion is to mesh with a steel gear with a gear ratio of 4:1. The Brinell hardness of the teeth is 200, and the tangential load transmitted by the...
Two 20° involute full depth spur gears are used to transmit the power and speeds shown....
Two 20° involute full depth spur gears are used to transmit the power and speeds shown. The material for both pinion and gear is specified as through- hardened steel tempered to 300 BHN surface hardness. Both pinion and gear are precision cut for "very accurate” gearing. For a factor of safety of 2 and assuming a diametral pitch, Pof 9. specify face widths of the pinion and gear using only the AGMA bending fatigue analysis. State all assumptions used to...
Two 20° involute full depth spur gears are used to transmit the power and speeds shown....
Two 20° involute full depth spur gears are used to transmit the power and speeds shown. The material for both pinion and gear is specified as through-hardened steel tempered to 300 BHN surface hardness. Both pinion and gear are precision cut for "very accurate" gearing. For a factor of safety of 2 and assuming a diametral pitch, Prof 9, specify face widths of the pinion and gear using only the AGMA bending fatigue analysis. State all assumptions used to determine...
There are two bevel gears in mate (a pinion and gear) determine the maximum diametral pitch (or closest to SF) based on the bending equations and the data below: (hint: use iterative approach, meaning it make take more than one try) (Also recall that diametral pitches are standardized, find the one the closest to standardized value while satisfying the FOS) . Determine the optimal diametral pitch, P, for the pinion (use bending equations) . Design/Safety Factor (SF)2.00 Overall Factor of...
QUESTION 3 Using the data below, determine the bending factor of safety for the pinion. Gear type: Spur Gear with Full depth teeth . Pressure angle (degrees) 20 . Np (teeth) 20 * n (rpms) 1200 ·H(hp) = 60 . Ng (teeth) 36 Pd (teeth/in) 4 face width (in) 3 . Quality factor (Q ) = 8 e gear mounting straddled between bearings Pinion (HB) 300 (material: steel) Gear (HB) = 240 (material: steel) . Are the teeth crowned? No...
3. A commercial enclosed gear drive consists of a 20 spur pinion having 16 teeth driving a 48-tooth gear. The pinion speed is 300 rev/min, the gear face width 2 in., and the diametral pitch 6 teeth/in. The gears are grade t steel, through-hardened at 200 Brinell, made to No. 6 quality standards, uncrowned, and are to be accurately and ngid mounted Assume a lion life ofi will transmitareliability of90%(KR 0.85), and use YN 1.355N 01:8 and Z 1. used...
The Isthmus Slough drawbridge has an open gear reduction for the span drive. A mating pair of gears pinion E and gear Fare located about mid-way in the 5 part speed reduction. The gear teeth are un- crowned open spur gears with a pressure angle o = 20 degrees. Both gears are made to an AGMA quality level Qv = 9 and have a measured hardness of HB = 183 made from through hardened Grade 1 Steel and are un-lapped....
designs
QIII) A 15-tooth, precision-made spur pinion is to drive a 25-tooth gear. A pitch of 6 teeth/in has been selected with a 2.25 in face width. Also, the teeth are to be 25 full depth, with a ddendum of 1.35/ pa for a pinion speed of 1150 rpm, and 10 hp is to transmitted under steady load conditions. The material selected for both gears is a through-hardened steel of a hardness of 302 Bhn . Determined the actors of...
Component design
Spur gear analysis
A speed-reducer has 200 full-depth teeth, and the single reduction spur-gear gearset has 22 and 60 teeth. The diametral pitch is 4 teeth/in and the face width is 3-1/4 in. The pinion shaft speed is 1145 rpm. The life goal of 5 year 24 hours per day service is about 3(10 9) pinion revolutions. The absolute value of the pitch variation is such that the transmission accuracy level number is 9. The materials are 4340...
6) [20 pts) Bending Stress in a Gear A steel spur pinion has a pitch of 6 teeth/in, 22 full-depth teeth with a cut profile, and a 20° pressure angle. The pinion runs at a speed of 1280 rev/min and transmits 15 hp to a 60-tooth gear. If the face width is 2 in., estimate the bending stress. Take the value of Lewis form factor, Y, from the table 14-2. The bending stress is kpsi.
7) [30 pts] Factor of Safety for Contact Stress A steel spur pinion has 16 teeth cut on the 20 full-depth system with a module of 8 mm and a face width of 90 mm. The pinion rotates at 150 rev/min and transmits 3 kW to the mating steel gear. This pinion is to mesh with a steel gear with a gear ratio of 4:1. The Brinell hardness of the teeth is 200, and the tangential load transmitted by the...
Two 20° involute full depth spur gears are used to transmit the power and speeds shown. The material for both pinion and gear is specified as through- hardened steel tempered to 300 BHN surface hardness. Both pinion and gear are precision cut for "very accurate” gearing. For a factor of safety of 2 and assuming a diametral pitch, Pof 9. specify face widths of the pinion and gear using only the AGMA bending fatigue analysis. State all assumptions used to...
Two 20° involute full depth spur gears are used to transmit the power and speeds shown. The material for both pinion and gear is specified as through-hardened steel tempered to 300 BHN surface hardness. Both pinion and gear are precision cut for "very accurate" gearing. For a factor of safety of 2 and assuming a diametral pitch, Prof 9, specify face widths of the pinion and gear using only the AGMA bending fatigue analysis. State all assumptions used to determine...
Most questions answered within 3 hours.
-
Data is only as good as its completeness. And we have all dealt
with incomplete data....
asked 1 minute from now -
Design a Class Diagram for a game of Dots and Boxes
that can do the
following:...
asked 3 minutes ago -
According to the February 2008 Federal Trade Commission report
on consumer fraud and identity theft, 23%...
asked 2 minutes ago -
Describe the Christian Anfinsen’s experimentS AND explain how
they have resulted in our current understanding of...
asked 13 minutes ago -
Do a research and write about the below areas of
SPAIN country business activities (GLOBAL
BUSINESS)...
asked 15 minutes ago -
Production and operations management involves three main types
of decisions that are made at three different...
asked 17 minutes ago -
When parked, your car is 6.4 m long. Unfortunately, your garage
is only 3.9 m long....
asked 27 minutes ago -
Use Python 3 in Jupyter
Write a function called countUnique that has one parameter which
is...
asked 24 minutes ago -
The WRT Corporation makes collections on sales according to the
following schedule:
30% in month of...
asked 32 minutes ago -
2C4H18O4+13O2=8CO2+18H2O
how many atoms of oxygen are required to generate 10.3 g of
carbon dioxide?
asked 51 minutes ago -
Based on USDA estimates, the cross-price elasticity for peanut
butter consumption with respect to grape jam...
asked 52 minutes ago -
Frankenstein book story teas reading
question and answer
asked 54 minutes ago