Homework Answers
Request Answer!
We need at least 10 more requests to produce the answer.
0 / 10 have requested this problem solution
The more requests, the faster the answer.
A spring loaded valve is to be used for operation of compressed air. The valve seat...
A spring loaded valve is to be used for operation of compressed air. The valve seat is 10 mm in radius. When the pressure on the valve reaches 1.05 N/mm2, its opening starts and when the pressure reaches 1.4 N/mm2, the valve must be completely open. During the operative pressure range, the valve lift is 6 mm. The steel used for the spring material has yield strength of 2000 MPa, and a shear modulus of 85 kN/mm2. Design the spring...
6. It is desired to design a valve spring ofLC. engine for the following details (a)...
6. It is desired to design a valve spring ofLC. engine for the following details (a) Spring load when valve is closed 80N (b) Spring load when valve is open =100 N (c) Space constraints for the fitment of spring are Inside guide bush diameter 24 mm Outside recess diameter 36 mm (d) Valve lift 5 mm (e) Spring steel has the following properties Maximum permissible shear stress 350 MPa Modulus of rigidity =84 kN/mm Find 1. Wire diameter, 2....
Design a close-coiled helical spring of silicon-manganese steel for the valve of an IC engine cap...
Design a close-coiled helical spring of silicon-manganese steel for the valve of an IC engine capable of exerting a net force of 65N when the valve is open and 54N when the valve is closed. The internal and external diameters are governed by space limitations, as it has to fit over bushing of 19 mm outside diameter and go inside a space of 38 mm diameter. The valve lift is 6 mm.
A vertical spring loaded valve is required for a compressed at a pressure of 1 N/mm2...
A vertical spring loaded valve is required for a compressed at a pressure of 1 N/mm2 gauge and must be fully open with a lift of 4 mm at a pressure of 1.2 N/mm gauge. The diameter of the port is 25 mm. Assume the allowable shear stress in steel as 480 MPa and shear modulus as 80 kN/mm2 Design a suitable close coiled round section helical spring having squared ground ends. Also specify initial compression and free length of...
spring relief disk 3. (40 pt.) A pressure cooker cooks a lot faster than an ordinary...
spring relief disk 3. (40 pt.) A pressure cooker cooks a lot faster than an ordinary pan by maintaining a higher pressure and temperature inside. The lid of a pressure cooker is well sealed, and steam can escape only through an opening in the middle of the lid. The pressure relief valve consists of a spring-loaded disk that is positioned over this opening. Consider that a certain portion of a pressure cooker is initially filled with water and put on...
spring relief disk 3.(40 pt.) A pressure cooker cooks a lot faster than an ordinary pan...
spring relief disk 3.(40 pt.) A pressure cooker cooks a lot faster than an ordinary pan by maintaining a higher pressure and temperature inside. The lid of a pressure cooker is well sealed, and steam can escape only through an opening in the middle of the lid. The pressure relief valve consists of a spring-loaded disk that is positioned over this opening. Consider that a certain portion of a pressure cooker is initially filled with water and put on top...
Mechanical springs
It is required to design a valve spring of IC Engine with following details:Spring load = 80 N, When valve is closedSpring load = 100 N, When valve is openSpace constraints for spring fitment are :Inside guide bush diameter = 24 mmOutside recess diameter = 36 mmValve lift = 5mmSpring steel has following properties :Ultimate tensile strength = 700 N/mm2Modulus of rigidity = 8.4 × 10^4 N/mm2Spring ends are square and ground. Permissible shear stress for spring wire = 0.5 Sut. Determine:...
Problem. (20 points) A helical compression spring will be used in a pressure relief valve. When...
Problem. (20 points) A helical compression spring will be used in a pressure relief valve. When the valve is closed the spring leneth is 50 mm, and the spring force is to be 7 N. The spring uses a wire diameter of d 1.5 mm and a mean spring diameter of D = 10 mm, and has a solid length ofl.- 30 mm. Use hard-drawn ASTM A227 wire, squared and ground ends, and ignore buckling since the spring is in...
2) [40 pts] Extension Spring Design A hard-drawn spring steel extension spring is to be designed...
2) [40 pts] Extension Spring Design A hard-drawn spring steel extension spring is to be designed to carry a static load F of 18 lbf with an extension of 1/2 in using a design factor of n = 1.5 in bending. Use full-coil end hooks with the fullest bend radius of r = D/2 and r2 = 2d. The free length must be less than 3 in, and the body turns must be fewer than 30. (Note: Integer and half-integer...
Exercises 1. (introduction) Sketch or plot the displacement of the mass in a mass-spring system for at least two per...
Exercises 1. (introduction) Sketch or plot the displacement of the mass in a mass-spring system for at least two periods for the case when Wn-2rad/s, 괴,-1mm, and eto =-v/5mm/s. 2. (introduction) The approximation sin θ ะ θ is reasonable for θ < 10°. If a pendulum of length 0.5m, has an initial position of 0()0, what is the maximum value of the initial angular velocity that can be given to the pendulum without violating this smll angle approximation? 3. (harmonic...
6. It is desired to design a valve spring ofLC. engine for the following details (a) Spring load when valve is closed 80N (b) Spring load when valve is open =100 N (c) Space constraints for the fitment of spring are Inside guide bush diameter 24 mm Outside recess diameter 36 mm (d) Valve lift 5 mm (e) Spring steel has the following properties Maximum permissible shear stress 350 MPa Modulus of rigidity =84 kN/mm Find 1. Wire diameter, 2....
A vertical spring loaded valve is required for a compressed at a pressure of 1 N/mm2 gauge and must be fully open with a lift of 4 mm at a pressure of 1.2 N/mm gauge. The diameter of the port is 25 mm. Assume the allowable shear stress in steel as 480 MPa and shear modulus as 80 kN/mm2 Design a suitable close coiled round section helical spring having squared ground ends. Also specify initial compression and free length of...
spring relief disk 3. (40 pt.) A pressure cooker cooks a lot faster than an ordinary pan by maintaining a higher pressure and temperature inside. The lid of a pressure cooker is well sealed, and steam can escape only through an opening in the middle of the lid. The pressure relief valve consists of a spring-loaded disk that is positioned over this opening. Consider that a certain portion of a pressure cooker is initially filled with water and put on...
spring relief disk 3.(40 pt.) A pressure cooker cooks a lot faster than an ordinary pan by maintaining a higher pressure and temperature inside. The lid of a pressure cooker is well sealed, and steam can escape only through an opening in the middle of the lid. The pressure relief valve consists of a spring-loaded disk that is positioned over this opening. Consider that a certain portion of a pressure cooker is initially filled with water and put on top...
Problem. (20 points) A helical compression spring will be used in a pressure relief valve. When the valve is closed the spring leneth is 50 mm, and the spring force is to be 7 N. The spring uses a wire diameter of d 1.5 mm and a mean spring diameter of D = 10 mm, and has a solid length ofl.- 30 mm. Use hard-drawn ASTM A227 wire, squared and ground ends, and ignore buckling since the spring is in...
2) [40 pts] Extension Spring Design A hard-drawn spring steel extension spring is to be designed to carry a static load F of 18 lbf with an extension of 1/2 in using a design factor of n = 1.5 in bending. Use full-coil end hooks with the fullest bend radius of r = D/2 and r2 = 2d. The free length must be less than 3 in, and the body turns must be fewer than 30. (Note: Integer and half-integer...
Exercises 1. (introduction) Sketch or plot the displacement of the mass in a mass-spring system for at least two periods for the case when Wn-2rad/s, 괴,-1mm, and eto =-v/5mm/s. 2. (introduction) The approximation sin θ ะ θ is reasonable for θ < 10°. If a pendulum of length 0.5m, has an initial position of 0()0, what is the maximum value of the initial angular velocity that can be given to the pendulum without violating this smll angle approximation? 3. (harmonic...
Most questions answered within 3 hours.
-
Hows does water affect the digestion of fats ?
asked 2 hours ago -
A buffer that contains 0.41 M of a base, B and 0.21 M of its
conjugate...
asked 2 hours ago -
Pleaaaaaaaasssssse help me please please it's more important
:((((((((((((((((((((
CASE STUDY
Nissan Company
Nissan Motor Company,...
asked 2 hours ago -
Calculate the concentration of hydronium and hyroxide ions in 1)
2.0 mol/L HNO3 2) 0.5 mol/L...
asked 2 hours ago -
In a loop-the-loop ride a car goes around a vertical, circular
loop at a constant speed....
asked 2 hours ago -
50 grams each of water (18.015 g/mol) and ethylene glycol
(C2H6O2) (62.07 g/mol) are mixed. At...
asked 2 hours ago -
The life expectancy of sport utility vehicles follows a normal
distribution with a mean of 145.8...
asked 3 hours ago -
If an object with mass of 5 kg is pushed with a force of 552 N,...
asked 2 hours ago -
Suppose your program already has a list called nums, which
contains several numbers. Write a for...
asked 2 hours ago -
A spherical shell with a finite thickness just barely floats in
water. If the shell is...
asked 2 hours ago -
Explain in detail whether the following is true or false:
Total factor productivity will rise only...
asked 3 hours ago -
A firm pays a $2.50 dividend at the end of year one
(D1), has a stock...
asked 3 hours ago