A solid shaft with 100-mm-diameter is made of cast iron and is subjected to the distributed and concentrated loadings as shown in Figure 9. The shear modulus of cast iron is 39GPa. (A) Determine the angle of twist at the free end A of the shaft due to these loadings. [9 marks] (B) Determine the maximum shear stress in this shaft. [4 marks] (C) Cast iron is a brittle material with an ultimate strength of 260MPa. Determine whether this structure...
The 60-mm-diameter solid shaft is subjected to the distributed and concentrated torsional loadings shown. Determine the absolute maximum and minimum shear stresses in the shaft's surface and specify their locations, measured from the free end. 10-25. The solid shaft is subjected to the distributed and concentrated torsional loadings shown. Determine the required diameter d of the shaft if the allowable shear stress for the material is Tallow = 60 MPa. 400 N·m 4 kN.m/m А. < 0.2 m 0.2 m...
Part A The 56-mm-diameter solid shaft is subjected to the distributed and concentrated torsional loadings shown, where T-470 N-m(Figure 1) Determine the absolute minimum shear stress on the shall's surface, and specify its location, measured from the fixed end C Express your answers, separated by a comma, to three significant figures. VAE 11 vec o ? T min MPa.mn Submit Request Answer Figure 1 of 1 Part B 2 kN.m/m Determine the absolute maximum shear stress on the shaft's surface,...
The solid shaft is subjected to the distributed and concentrated torsional loadings shown, where T = 410 N·m. 2 kN.m/m 0.4 m / B 600 N·m A 0.4 m d The allowable shear stress for the material is Tallow = 175 MPa. Part A Determine the required diameter d of the shaft.
The power loading on a uniform shaft of 20 mm diameter solid circular cross section is shown in Figure 2. The speed of the shaft is 1200 rpm. The shear modulus (G) of steel may be taken as 80 GPa C (a) Sketch the torque diagram; (b) Determine the maximum shear stress in the shaft (c) Calculate the angle of twist between the two ends of the shaft 1.2 m 1.8 m 6 kW 11 kW A Тв TA Tc...
The 50-mm-diameter solid shaft is made of A-36 steel and is subjected to the distributed and concentrated torsional loadings shown where T = 230 N-m. 2 kNm 600 Nm B 0.8 m 0.6 m Part A Determine the angle of twist at the free end A of the shaft due to these loadings. Use Gst = 75.0 GPa Express your answer to three significant figures and include appropriate units. μΑ ? O= Value Units
5. A 38-mm-diameter solid steel shaft, 2 m long, is subjected to a torque of 600 N.m, as shown below. The steel is AISI 1020 hot-rolled. Calculate a) The maximum torsional shear stress b) The angle of twist, ?, in degrees, ifG2 79.3 x 10"MPas 79.3 x 10, N/m2 Te TL Recall radian 57.3 32 JG
The gears attached to the fixed-end steel shaft are subjected to the torques shown in the figure. If the shear modulus of elasticity is 150 GPa a determine the following: nd the shaft has a diameter of 14 mm, a. Sketch the torque diagram along the steel shaft. b. Determine the maximum shear stress at Tmax and specify location. c. Sketch the shear stress distribution along the radial line at location specified in (b). d. Determine the displacement of the...
The 50-mm-diameter solid shaft is made of A-36 steel and is subjected to the distributed and concentrated torsional loadings shown where T = 140 N-m. 2 kNm 600 Nm B 0.8 m 0.6 m A Part A Determine the angle of twist at the free end A of the shaft due to these loadings. Use Gst = 75.0 GPa Express your answer to three significant figures and include appropriate units. μΑ ? 22 % Å O 0.303 Submit Previous Answers...
The 50-mm-diameter solid shaft is made of A-36 steel and is subjected to the distributed and concentrated torsional loadings shown where T = 140 N-m. 2 kNm 600 Nm B 0.8 m 0.6 m A Part A Determine the angle of twist at the free end A of the shaft due to these loadings. Use Gst = 75.0 GPa Express your answer to three significant figures and include appropriate units. μΑ ? 22 % Å O 0.303 Submit Previous Answers...