Voltmeters are added into the circuit to check for voltage at the proper motor coils. Refer to Two-Speed Reversing Conveyor Line Diagram on page 47. Determine each meter reading when the conveyor is operating in low speed and running the forward direction.
Voltmeters are added into the circuit to check for voltage at the proper motor coils. Refer...
The equivalent circuit of a 440 V, 3-phase, 8 pole, and 50 Hz star-connected induction motor is shown in figure 1. The short-circuit test is conducted with a locked rotor and a line current of 80 A. The open-circuit test is conducted by supplying the stator winding at rated voltage and at the rotor is rotating freely without any mechanical load.a) Determine the line voltage and power factor on the short circuit test;b) We need to apply a low...
Question: The equivalent circuit parameters of a 440 V, 3-phase, 8-poles, and 50 Hz star connected motor are given below. The short-circuit test is conducted with a locked rotor and a line current of 80 A. The open-circuit test is conducted by supplying the stator winding at rated voltage and at the same time driving the rotor in the same direction as the rotating field, at synchronous speed; s=0.R1 = 0.1, X1 = 0.5, RI2 = 0.1, XI2 = 0.5,...
Question: The equivalent circuit of a 440 V, 3-phase, 8 pole, and 50 Hz star-connected induction motor is shown in figure 1. The short-circuit test is conducted with a locked rotor and a line current of 80 A. The open-circuit test is conducted by supplying the stator winding at rated voltage and at the rotor is rotating freely without any mechanical load. Fig. 1 The per-phase equivalent circuit of a 3-phase induction motora) Determine the line voltage and power factor on the...
Question: The equivalent circuit parameters of a 440 V, 3-phase, 8-poles, and 50 Hz star connected motor are given below. The short-circuit test is conducted with a locked rotor and a line current of 80 A. The open-circuit test is conducted by supplying the stator winding at rated voltage and at the same time driving the rotor in the same direction as the rotating field, at synchronous speed; s=0.R1 = 0.1, X1 = 0.5, RI2 = 0.1, XI2 = 0.5, Xm = 20, Rm = 100...
2. A string of lights is wired in a series circuit. When one light bulb ns out, A B the other bulbs will dim. none of the other bulbs will be lit. C D e burnt out bulb becomes a fire hazard. all of the other bulbs will be lit. 2. A string of lights is wired in a series circuit. When one light bulb ns out, A B the other bulbs will dim. none of the other bulbs will...
3ELEC 3600. Problem H8 3-phase Wound Rotor Induction Motor This sheet is page 1. Number all pages. Consider the following induction machine THREE-PHASE INDUCTION MOTOR DATA* Ratings Line Voltage 2400 V; 72.17 A; Horsepower-300 hp stator frequency60 Hz Design W Poles -4; **Equivalent Circuit Values (in stator ohms Rated Freq)** R1 0.30000 R2'- 0.47159 X2'-1.73000; Jm2.5000 kg-m sq Thevenin Equivalent Circuit Values: RT-0.28524; slip, speed for max Torque0.1375; Rotational Loss Torque-TRL 0.18689 x (speed in rad/s) Nm X1 -1.73000 Xm67.740...
(might be 1 or 2, MCQ questions were having images given with them, which we couldn't insert, so ignore those questions if you cannot answer, sorry for inconveinience created, i tried to delete them but might be couldn't done all) 3) Single phase induction motors work because: a) The oscillating magnetic field can induce starting torque in a rotor. b) The oscillating magnetic field can induce running torque in a rotor. c) A capacitance or inductance can create the phase...
Notes for lab dc02-Resistors and the Color Code will skip are Part 2 e, g: Part 4; Exercises 2, 4,5,6 and 3. It is important to answer the exercises correctly in each labl you should include the appropriate prefix for the unit in the Numerical Value We will not be Volt using the Volt-Ohm meter (VOM) for this lab, so skip the parts that ask for VOM measurements. The parts we You do need to complete Exercises1 Note that in...
summatize the following info and break them into differeng key points. write them in yojr own words apartus 6.1 Introduction—The design of a successful hot box appa- ratus is influenced by many factors. Before beginning the design of an apparatus meeting this standard, the designer shall review the discussion on the limitations and accuracy, Section 13, discussions of the energy flows in a hot box, Annex A2, the metering box wall loss flow, Annex A3, and flanking loss, Annex...
summarizr the followung info and write them in your own words and break them into different key points. 6.5 Metering Chamber: 6.5.1 The minimum size of the metering box is governed by the metering area required to obtain a representative test area for the specimen (see 7.2) and for maintenance of reasonable test accuracy. For example, for specimens incorporating air spaces or stud spaces, the metering area shall span an integral number of spaces (see 5.5). The depth of...