Q 5 please DC 28 29 Questions 28 5. A convergent nozzle has an inlet area...
g through a nozzle. The inlet pressure is p 3.7 kPa (gage) air flowing and the air exhausts into the atmosphere. The nozzle has an inlet diameter of 60 mm and an exit diameter of 10 mm, and the nozzle is connected to the supply pipe by flanges. Find the force required to hold the nozzle stationary. Assume the air has a constant density of 1.22 kg/m Neglect the weight of the nozzle. m Flanges Flow 2 g through a...
Determine the area and velocity at the exit of the convergent nozzle through which it flows an isentropic gas (k = 1,4; R = 287Nm/kg.K). What is the lowest possible value for the outlet of the nozzle while maintaining isoentropic flow? (For the same input conditions). Data: Pressure1 = 207 kPa ; Density1 = 1,3 kg/m³ ; Velocity1 = 47,2 m/s ; Area1 = 0,1m² . Pressure2 = 172,5 kPa
Show all work and answer all parts of the problem please. The 45 degree elbow nozzle discharges water into the atmosphere. The cross-sectional area of the elbow is 25 cm2 150 cm2 at the inlet and 25 cm2 at the exit. Velocity at point 1 and 2 are given as 2 m/s and 12 m/s 450 respectively. The gage pressure at 1 is 73 kPa 150 em2 30 cm The elevation difference between the centers of the exit and the...
Question 2 (30 marks) (a) A fluid flowing into a nozzle with specific enthalpy of 2980 kJ/kg and the velocity is 80 m/s. At the exit of the nozzle, the specific enthalpy of the fluid drops to 2670 kJ/kg. The nozzle orientation is horizontal and the heat loss is negligible. Given that the nozzle inlet area is 0.25 m2 and the specific volume of the fluid is 0.2 m2/kg, calculate the velocity of the fluid at exit, the mass flow...
5) Oil (S.G=0.9) flows enters the pipe shown through the bottom inlet at a rate of 0.25 m/min and is discharged to at P. - 76 kPa the nozzle outlet at the top. The pipe has a diameter Di = 40 mm at the entrance and a diameter D2 = 20 mm at the exit. If P. = 76 kPa, P2 =20 kPa, and the weight the oil and the piping is negligible, what is the reaction moment at flange...
a and c please a. For a bypass mass flow of 50 kg/s with an inlet temperature of 300 K and inlet velocity of 170 m/s, the work input from the fan is -2.7457 MW. What is the temperature of the air after the fan? b. The way that an engine changes the thrust is by changing the rotational speed of the fan, which changes the work input and hence the enthalpy of the air after the fan. Use Matlab...
8-C) As shown below water is pumped and sprayed through a nozzle into the atmosphere at 20 m/s at an elevation 10 m above the reservoir surface. The mass flow rate is 40 kg/s and the volumetric flow rate is 0.040 m3/s. The large diameter inlet pipe total length is 50 m. The pump effidency is 65%. The longer smaller diameter pipe leaving the pump is 200 m in total length. The pipes have different diameters as indicated below. The...
Problem 1. Water flows from a large tank through a smooth pipe of length 80 m. Both the tank free surface and jet exit are exposed to the atmosphere. Take the density of water p = 1000 kg/m3, dynamic viscosity of water u = 0.001 kg/m.s, atmospheric pressure = 100 kPa, and gravity = 9.8 m/s2. Calculate the volumetric flow rate through the pipe. Neglect entrance losses to the pipe. Hint: Consider the inlet and outlet sections of the pipe...
Problem 1. Water flows from a large tank through a smooth pipe of length 80 m. Both the tank free surface and jet exit are exposed to the atmosphere. Take the density of water p = 1000 kg/m3, dynamic viscosity of water j = 0.001 kg/m.s, atmospheric pressure = 100 kPa, and gravity = 9.8 m/s2. Calculate the volumetric flow rate through the pipe. Neglect entrance losses to the pipe. Hint: Consider the inlet and outlet sections of the pipe...
1. Water enters the constant 130-mm inside-diameter tubes of a boiler at 7 MPa and 65°C and leaves the tubes at 6 MPa and 450°C with a velocity of 80 m/s. Calculate the velocity of the water at the tube inlet and the inlet volume flow rate. [5-14] 2. Air enters a nozzle steadily at 50 psia, 140°F, and 150 ft/s and leaves at 14.7 psia and 900 ft/s. The heat loss from the nozzle is estimated to be 6.5...