Mechanics of solid help pleaseHomework Answers
Add Answer to:
Mechanics of solid help please
Question 2 An aluminum tube with an outside diameter of 1.000...
A stainless steel tube with an outside diameter of 70 mnm and a wall thickness of...
A stainless steel tube with an outside diameter of 70 mnm and a wall thickness of 5 mm is used as a compression member. If the axial stress in the member must be limited to 200 MPa, determine the maximum load P that the member can support. O A. 294 kN B. 864 kN O C. 173 kN ○ D. 340 kN
A hollow steel [E-30,000 ksi] tube (1) with an outside diameter of 3.25 in, and a...
A hollow steel [E-30,000 ksi] tube (1) with an outside diameter of 3.25 in, and a wall thickness of 0.209 in, is fastened to a solid 2.25-in.-diameter aluminum (E = 10,000 ksi] rod. The assembly is attached to unyielding supports at the left and right ends and is loaded as shown. Assume P-19 kips, Q-8 kips, L,-5 ft, L2-7ft, and L-7 ft. Determine (a) the stresses in all parts of the axial structure. (b) the deflections of joints B and...
the hollow tube down has an outside diameter of 45 mm and an inside diameter of...
the hollow tube down has an outside diameter of 45 mm
and an inside diameter of 40 mm. the tube is made of an aluminum
alloy with a minimum yield strength of 280 MPa. the bending load is
F =1.5 kN, the axial load is P = 10kN and the twisting moment is T
= 70 N-m. Determine the factor of safety based on the stress at
point A using (a) the maximum shear stress theory and (b) the
distortion...
1. The following is a one-layer truss structure fabricated from aluminum tubing with outside diameter and...
1. The following is a one-layer truss structure fabricated from aluminum tubing with outside diameter and wall thickness as 0.4 inch and 0.05 inch, respectively. The Young's modulus and Poisson's ratio for aluminum are E= 10 x 10°psi, v=0.33, respectively. The applied load P is 60 Ib. = 60° B Ra UR The internal force for member AC is: -30 lb 34.6 lb 30 lb -34.6 lb Question 2 1 points Save Answer 1. The following is a one-layer truss...
1. The following is a one-layer truss structure fabricated from aluminum tubing with outside diameter and...
1. The following is a one-layer truss structure fabricated from aluminum tubing with outside diameter and wall thickness as 0.4 inch and 0.05 inch, respectively. The Young's modulus and Poisson's ratio for aluminum are E= 10 x 10°psi, v=0.33, respectively. The applied load P is 60 Ib. Please answer = 60° B Ra all Cled URb The internal force for member AC is: -30 lb 34.6 lb 30 lb -34.6 lb Question 2 1 points Save Answer 1. The following...
P6.074 The torsional assembly consists of a cold-rolled stainless steel tube connected to a solid cold-rolled...
P6.074 The torsional assembly consists of a cold-rolled stainless steel tube connected to a solid cold-rolled brass segment at flange C. The assembly is securely fastened to rigid supports at A and D Stainless steel tubes (1) and (2) have an outside diameter of 3.125 in, a wall thickness of 0.082 in., a shear modulus of G = 14200 ksi, and an allowable shear stress of 38 ksi. The solid brass segment (3) has a diameter of 1.3125 in., a...
1. The following is a one-layer truss structure fabricated from aluminum tubing with outside diameter and...
1. The following is a one-layer truss structure fabricated from aluminum tubing with outside diameter and wall thickness as 0.4 inch and 0.05 inch, respectively. The Young's modulus and Poisson's ratio for aluminum are E = 10 x 10Ⓡpsi, v=0.33, respectively. The applied load P is 60 lb. °60 - 8ܢ Bܢ Ra Rb The internal force for member AC is: 34.6 lb -34.6 lb -30 lb O 30 lb The cross-sectional area of the tube is: O 0.045in2 O...
Mechanics and Materials Help Question 1. (a) A steel tube having inner and outer dimeters of...
Mechanics and Materials Help
Question 1. (a) A steel tube having inner and outer dimeters of 1.5 in. and 2 in., respectively, is tuming at 45 rev/min. If the allowable shear stress (Tallow) of the tube material is 10 ksi, determine the horse power (hp) transmitted by the tube. (20 points) (b) The A-36 solid steel shaft is 3.5 m long and has a diameter of 60 mm. The shaft is used to transmit a torque of T = 524...
A solid aluminum [E = 76 GPa] rod (1) is connected to a solid bronze [E = 93 GPa] rod (2) at flange B
A solid aluminum [E = 76 GPa] rod (1) is connected to a solid bronze [E = 93 GPa] rod (2) at flange B, as shown. Aluminum rod (1) has an outside diameter of 31 mm and bronze rod (2) has an outside diameter of 15 mm. The norma stress in the aluminum rod must be limited to 128 MPa, and the normal stress in the bronze rod must be limited to 97 MPa. Assume L1 = 180 mm and...
The torsional assembly in the Figure above consists of a cold-rolled stainless-steel tube AC with an...
The torsional assembly in the Figure above consists of a
cold-rolled stainless-steel tube AC with an outside diameter of 4
in., a wall thickness of 0.2 in., a shear modulus of G = 12,500
ksi, and an allowable shear stress of 35 ksi. The tube AC is
connected to a solid cold-rolled brass segment CD at the flange C
and has a diameter of 2.50 in., a shear modulus of G = 5,600 ksi,
and an allowable shear stress of...
A stainless steel tube with an outside diameter of 70 mnm and a wall thickness of 5 mm is used as a compression member. If the axial stress in the member must be limited to 200 MPa, determine the maximum load P that the member can support. O A. 294 kN B. 864 kN O C. 173 kN ○ D. 340 kN
A hollow steel [E-30,000 ksi] tube (1) with an outside diameter of 3.25 in, and a wall thickness of 0.209 in, is fastened to a solid 2.25-in.-diameter aluminum (E = 10,000 ksi] rod. The assembly is attached to unyielding supports at the left and right ends and is loaded as shown. Assume P-19 kips, Q-8 kips, L,-5 ft, L2-7ft, and L-7 ft. Determine (a) the stresses in all parts of the axial structure. (b) the deflections of joints B and...
the hollow tube down has an outside diameter of 45 mm
and an inside diameter of 40 mm. the tube is made of an aluminum
alloy with a minimum yield strength of 280 MPa. the bending load is
F =1.5 kN, the axial load is P = 10kN and the twisting moment is T
= 70 N-m. Determine the factor of safety based on the stress at
point A using (a) the maximum shear stress theory and (b) the
distortion...
1. The following is a one-layer truss structure fabricated from aluminum tubing with outside diameter and wall thickness as 0.4 inch and 0.05 inch, respectively. The Young's modulus and Poisson's ratio for aluminum are E= 10 x 10°psi, v=0.33, respectively. The applied load P is 60 Ib. = 60° B Ra UR The internal force for member AC is: -30 lb 34.6 lb 30 lb -34.6 lb Question 2 1 points Save Answer 1. The following is a one-layer truss...
1. The following is a one-layer truss structure fabricated from aluminum tubing with outside diameter and wall thickness as 0.4 inch and 0.05 inch, respectively. The Young's modulus and Poisson's ratio for aluminum are E= 10 x 10°psi, v=0.33, respectively. The applied load P is 60 Ib. Please answer = 60° B Ra all Cled URb The internal force for member AC is: -30 lb 34.6 lb 30 lb -34.6 lb Question 2 1 points Save Answer 1. The following...
P6.074 The torsional assembly consists of a cold-rolled stainless steel tube connected to a solid cold-rolled brass segment at flange C. The assembly is securely fastened to rigid supports at A and D Stainless steel tubes (1) and (2) have an outside diameter of 3.125 in, a wall thickness of 0.082 in., a shear modulus of G = 14200 ksi, and an allowable shear stress of 38 ksi. The solid brass segment (3) has a diameter of 1.3125 in., a...
1. The following is a one-layer truss structure fabricated from aluminum tubing with outside diameter and wall thickness as 0.4 inch and 0.05 inch, respectively. The Young's modulus and Poisson's ratio for aluminum are E = 10 x 10Ⓡpsi, v=0.33, respectively. The applied load P is 60 lb. °60 - 8ܢ Bܢ Ra Rb The internal force for member AC is: 34.6 lb -34.6 lb -30 lb O 30 lb The cross-sectional area of the tube is: O 0.045in2 O...
Mechanics and Materials Help
Question 1. (a) A steel tube having inner and outer dimeters of 1.5 in. and 2 in., respectively, is tuming at 45 rev/min. If the allowable shear stress (Tallow) of the tube material is 10 ksi, determine the horse power (hp) transmitted by the tube. (20 points) (b) The A-36 solid steel shaft is 3.5 m long and has a diameter of 60 mm. The shaft is used to transmit a torque of T = 524...
The torsional assembly in the Figure above consists of a
cold-rolled stainless-steel tube AC with an outside diameter of 4
in., a wall thickness of 0.2 in., a shear modulus of G = 12,500
ksi, and an allowable shear stress of 35 ksi. The tube AC is
connected to a solid cold-rolled brass segment CD at the flange C
and has a diameter of 2.50 in., a shear modulus of G = 5,600 ksi,
and an allowable shear stress of...
Most questions answered within 3 hours.
-
(63
#14)
which of the following statments best describes how chamging
the concentration of the substances...
asked 22 minutes ago -
In the following reaction, which element is undergoing
oxidation: Na2SO3 + N2O --> N2 + Na2SO4...
asked 1 hour ago -
Which of the following pairs of ions have the same electron
configuration?
I: Br− and Se2−...
asked 3 hours ago -
The Foremost Composite Materials Company is planning a two-day
sales conference for October 19-20. The conference...
asked 4 hours ago -
3) Illustrate the observed pattern of relatedness of organisms
versus adaptations to specific conditions. This means...
asked 4 hours ago -
In winter a lake has a 0.35 m thick ice layer over 1.10 m of
water....
asked 5 hours ago -
Assuming the following has been encrypted with a Vigenere cipher
below, use the method(s) and assumptions...
asked 5 hours ago -
How would I use switch statements to write a program that will
take an input of...
asked 5 hours ago -
Imagine a reaction in which methane gas combusts at a constant
pressure of 1 atm and...
asked 5 hours ago -
Two parallel wires (each 12 m in length) are separated by a
distance of 0.065 m...
asked 5 hours ago -
Suppose there were three masses at the corner of uniform
equilateral triangle. The masses are m1...
asked 5 hours ago -
Situation: A building that is 618 m above the ground floor. How
many times would a...
asked 5 hours ago