A shaft 1.8 m long and 125 mm in diameter has a torque of 20 kNm...

Question

Question

A shaft 1.8 m long and 125 mm in diameter has a torque of 20 kNm and a deflection angle of 1 degree. Calculate:

Answer 1

Answer #1

day Date length = 1.8m & Diam = 125mm = 125mm x 103 m. Porque = 20x103Nm 0 = 1 = 0.01745 rad Now, we all know Tonional stren

PLEASE APPRECIATE THE WORK DONE ..............THANK YOU VERY MUCH

Answer 2

Similar Homework Help Questions

160 mm 10 mm A hollow cylindrical steel shaft is 1.5 m long and has inner...

160 mm 10 mm A hollow cylindrical steel shaft is 1.5 m long and has inner and outer diameters respectively equal to 40 and 60 mm. The allowable shearing stress is 120 MPa with a modulus of rigidity (shear modulus) G-77 GPa, assuming fully elastic deformation. (a) What is the largest torque that can be applied to the shaft? (5 points) (b) What is the corresponding minimum value of the shearing stress in the shaft? (5 points) (c) What are...
#3 4) A mild steel solid shaft 1.8 meters long and 30 mm in diameter withstands...

#3 4) A mild steel solid shaft 1.8 meters long and 30 mm in diameter withstands a tor shear modulus for this steel is 7 shaft. o GPa. Determine the shear stress in the shaft and the angle of twist of the
The power loading on a uniform shaft of 20 mm diameter solid circular cross section is...

The power loading on a uniform shaft of 20 mm diameter solid circular cross section is shown in Figure 2. The speed of the shaft is 1200 rpm. The shear modulus (G) of steel may be taken as 80 GPa C (a) Sketch the torque diagram; (b) Determine the maximum shear stress in the shaft (c) Calculate the angle of twist between the two ends of the shaft 1.2 m 1.8 m 6 kW 11 kW A Тв TA Tc...

75 mm 1.5 m T = 48 N·m 2 m 150 mm Two solid steel 20-mm-diameter...

75 mm 1.5 m T = 48 N·m 2 m 150 mm Two solid steel 20-mm-diameter shafts are coupled together using the perfectly meshed gears shown. Shaft DC is fixed to the wall at D and supported with a frictionless journal bearing. Shaft EF is supported with two frictionless journal bearings. The modulus of rigidity of steel is 80 GPa. Before the torque is applied, the angle of twist in each shaft is zero, and the angle of rotation of...
TORSION

a) A hollow circular shaft designed to have an inner diameter of 0.7Do; where Do is an outer diameter.i) Determine the inner and outer diameters of the shaft if the maximum allowable shearing stress is Y0 N/mm2 and torque is X00 kNm. Then, calculate the polar moment of inertia.ii) By using inner diameter calculated in (i), calculate the maximum shearing stress and a new torque, if the shaft is changed to solid circular shaft. The shaft is 1.5 m long with the twisted through...
(b) The A-36 solid steel shaft is 3.5 m long and has a diameter of 60...

(b) The A-36 solid steel shaft is 3.5 m long and has a diameter of 60 mm. The shaft is used to transmit a torque of T = 524 N·m from the engine to the generator. Determine the angle of twist (0) of the shaft. The shear modulus of elasticity (G) of the shaft material is 75 GPa.

(b) The A-36 solid steel shaft is 3.5 m long and has a diameter of 60...

(b) The A-36 solid steel shaft is 3.5 m long and has a diameter of 60 mm. The shaft is used to transmit a torque of T=524 N·m from the engine to the generator. Determine the angle of twist (%) of the shaft. The shear modulus of elasticity (G) of the shaft material is 75 GPa. (10 points)
A torque of 20 N-m is delivered to het gear A from the motor. If gear Cis motor. If gear C is sud...

A torque of 20 N-m is delivered to het gear A from the motor. If gear Cis motor. If gear C is suddenly locked so that it does not 100 mm 30 mm mW- rotate. If gear B is free to rotate, then determine (a) angle of twist of F with respect to E, and angle of twist of Fwith respect to D. The shaft which is mounted a set of bearing G and H is carrying all the gears...
1. (20 pts.) For the figure shown: a. What is the largest torque that can be...

1. (20 pts.) For the figure shown: a. What is the largest torque that can be applied to the shaft if the shearing stress is not to exceed 120 MPa b. What is the corresponding minimum value of the shearing stress in the shaft? c. What torque should be applied to the end of the shaft to produce a twist of 2 degrees? Use value G-71-GPa for the modulus of rigidity of steel 60 mm 40 mm 1.5 m

Section 2. Problem 6 (25 pts.) A hollow shaft 36 inches long tranmits 125 HP at...

Section 2. Problem 6 (25 pts.) A hollow shaft 36 inches long tranmits 125 HP at 1100 rpm. The shaft is made out of steel with a modulus of rigidity of 11000 ksi. The shaft has an allowable sear stress of 12 ksi and an allowable angle of twist of 2.5 degreees over the 36 inche length. The inside diameter of the shaft is 0.6 that of the outside diameter of the shaft. Determine: a) the required inside and outside...