1. Given the following set of retrieved documents with relevance judgments
TERM T1 T2 T3 T4 T5 T6
QUERY 0 0 0 2 1 0
REL D1 0 4 4 0 2 0
REL D2 0 2 6 0 0 0
REL D3 6 0 0 0 0 0
NOT REL D4 4 0 4 8 8 10
a. Calculate a new query using a factor of 1/2 for positive feedback and 1/4 for negative feedback
b. Determine which documents would be retrieved by the original and by the new query
We need at least 10 more requests to produce the answer.
0 / 10 have requested this problem solution
The more requests, the faster the answer.
1. Given the following set of retrieved documents with relevance judgments TERM T1 T2 T3 T4...
We have the following sequence of instructions in MIPS lw $t4, 4($s1) or $t1, $t2, $t3 or $t2, $t1, $t4 or $t1, $t1, $t2 1) Indicate any hazards and what the hazard types are. 2) Assume there is no forwarding in this pipelined processor and each stage takes 1 cycle. Draw the pipeline chart and calculate how many cycles are consumed 3) Assume there is forwarding in this pipelined processor and each stage takes 1 cycle. Draw the pipeline chart...
pi=3.14
Please show all steps when
answering:
Test the linear relationship between squared period
T2 and the length of the pendulum d.
Plot the function T^2=f(d)
You can use the following values:
d1=34;
T1=1.097; g1= 1114.225
cm/s^2
d2=25;
T2=1.0082; g2= 969.986
cm/s^2
d3=17.1;
T3=0.839
g3= 958.057 cm/s^2
d4=42.5;
T4=1.301 g4=
990.270 cm/s^2
d5=49;
T5=1.408
g5= 974.827 cm/s^2
2
2
An experiment to investigate the effects of various dietary
starch levels on milk production was conducted on four cows. The
four diets, T1, T2, T3, and T4, (in order of increasing starch
equivalent), were fed for three weeks to each cow and the total
yield of milk in the third week of each period was recorded (i.e.
third week to minimize carry-over effects due to the use of
treatments administered in a previous period). That is, the trial
lasted 12...
A Student cycle engine is analyzed using the cold air-standard method. Given the definition of each process in the cycle, determine the thermal efficiency of the engine for each set of defined ratios listed below. All ratios are given as the larger value over the smaller one. --Given Values-- Process 1-2 = Isentropic compression & volume ratio=rv12 Process 2-3 = Isobaric compression & volume ratio=rv23 Process 3-4 = Isometric heat addition & temperature ratio=rT34 Process 4-5 = Isobaric heat addition...
1. In the design of an experiment we have a treatment T with four levels T1,T2,T3, T4. We are planning to use CRD model and we have only n-20 observations available. Gj, Г, 2, 3, 4:3 How should we allocate the n observations to the four treatments to minimize the average variance of the estimated treatment effects AV = 슷 (var(T1) + var(T2) + var(fs) + var(T4)) UaT T4 Hint: Find the values of r, by minimizing AV subject to...
Today's problem Combination circuit
In the following logic circuit, inputs a and b were as shown
in the blue diagram on the right in each time period T1 to T6.
Which of c1-c5 is the correct output c?
Tip: 1 Let's derive a logical formula. 2 Let's make a truth
table. The waveform obtained from 32 and the waveform of
c1-c5
Let's compare.
Т1 Т2 T3 T4 15 T6 1 а о А) 1 b 0 Т1 T2 T3 T4...
In Lab
1. Check all the components for their working
2. Insert the appropriate IC into the IC base
3. Make connections as shown in the circuit diagram
4. Verify the Truth Table and observe the outputs
VCSQA QB QC QD CLK1 CLK2 14 13 12 11 10 9 00 IC 7495 1 2 3 4 5 6 7 B с MODE CONTROL GND SERIAL INPUT (Right PARALLEL Shift) INPUTS Lab Task 1: SERIAL IN SERIAL OUT (SISO) (Right Shift)...
Table 3.1
Time, t (s)
Position, x (m)
tn/t1
Time Squared, t^2 (s^2)
(tn)^2/(t1)^2
xn/x1
t1, 0.40
x1, 0.25
1.0
.16
1
1
t2, 0.80
x2, 0.36
2.0
.64
4
1.4
t3, 1.2
x3, 0.52
3.0
1.4
9
2.1
t4, 1.6
x4, 0.71
4.0
2.6
16
2.8
t5, 2.0
x5, 0.95
5.0
4.0
25
3.8
t6, 2.4
x6, 1.2
6.0
5.8
36
4.8
Linear fit equation for Position Vs. Time: 0.545x - 0.0530
Quadratic fit equation for Position Vs. Time:...
In the code below i am using a LS-3006 SERVO on the arduino uno and everytime i hit the pushbutton to input a time the servo comes on. Would anyone be able to tell me what a solution is to this problem? Thanks #include <Wire.h> #include <DS3231.h> #include <Servo.h> #include <LiquidCrystal.h> #include <Keypad.h> const byte ROWS = 4; // # of rows const byte COLS = 4; // # of columns // Define the Keymap char keys[ROWS][COLS] = { {'1','2','3','A'},...
[Question 3, 12 points total, including 3.1-3.2] (minhasbing) Consider the following matrix, d1 0 d4 0 1 1 4 6 1 3 5 2 0 0 1 0 d2 1 0 1 0 0 1 d3 1 1 0 1 1 0 0 0 0 where each column represents a document (altogether we have 4 documents, di, d2, d3 and d4), and the number of rows is the size of the universal word set. Note the first column, ie, column...