Plz answer Problem: What is the minimum strain at failure in the tension steel in beams?

Question

Question

Plz answer
Problem: What is the minimum strain at failure in the tension steel in beams?

Answer 1

Answer #1

The minimum strain at failure in the tension steel in beams as per Limit State Method of IS 456:2000 is 0.002+0.87*(fy/Es).

Where fy=Characteristic Strength of Steel

Es=Young's Modulus of Steel.

Answer 2

Similar Homework Help Questions

4. Using ACI Code, determine the magnitude of the load at failure (assume strain in the steel is ...

We were unable to transcribe this imageWe were unable to transcribe this image4. Using ACI Code, determine the magnitude of the load at failure (assume strain in the steel is 0.005) 4. Using ACI Code, determine the magnitude of the load at failure (assume strain in the steel is 0.005)
Plz show in graph paper if possible. Thanks :) find stress, strain and draw the graph....

Plz show in graph paper if possible. Thanks :) find stress, strain and draw the graph. if it is blurry. plz zoom Part II: Problem 1 (15 points) A tension test was performed on a steel specimen having an original diameter of 12.5 mm and a gauge length of 50 mm. The data is listed in the table below. Plot the stress strain diagram and determine approximately the modulus of elasticity, the yield stress, the ultimate stress, and the rupture...
1) The strain in the steel at failure is most nearly: A. 0.002 B. 0.005 C....

1) The strain in the steel at failure is most nearly: A. 0.002 B. 0.005 C. 0.018 D. 0.023 E. 0.003 2) Find the development length of the # 8 bar in tension. A 12 ft cantilever beam 21 in. wide x 30 in, deep is reinforced by four # 8 bars as shown. Given fc 4000 psi and fy 60,000 psi. 3 in. is the cover to the center of the # 8 bar 21" #8 bars are spaced...

A crane at a construction site is used to lift and move steel beams and place...

A crane at a construction site is used to lift and move steel beams and place them on the building under construction as needed. The motion of the beam is measured tension in the cable and the time intervals the tension is applied. For example, consider the following situation: The beam is initially suspended, stationary, above the ground. The tension in the cable is T0 = 2580 N. Next, the tension in the cable is T1 = 2660 N for...
2) Using the stress-strain curve for a steel alloy shown in the following figure answer the...

2) Using the stress-strain curve for a steel alloy shown in the following figure answer the following questions: 600 500 400 500 400 300 300 200 200 100 100 0.000 0.002 0.006 0.004 Strain 0.00 0,04 0.08 0.12 0.16 0.20 Using the same steel alloy, consider a cylindrical specimen 15 mm in diameter pulled in tension, if a load of 85,000 N is applied: h) Calculate the approximate ductility in percent elongation, (consider the final elongation as the elongation at...
Problem 5.2.1 A steel column is column length is 10ft. What is the resulting unit strain?...

Problem 5.2.1 A steel column is column length is 10ft. What is the resulting unit strain? 0.055. The original Column in compression

1. For the beams shown, find the location of the neutral axis relative to the compression...

1. For the beams shown, find the location of the neutral axis relative to the compression face, c, and the strain in the steel, Et. Is the section tension controlled, compression controlled or in the transition zone? What is the nominal moment21 strength, Mn, the strength reduction factor, , and the design moment strength, Mn 20 3-48 a) fe 3000 psi ASTM A615 Gr60 reinforcement QUESTION2 Problem 1a: What is the nominal moment strength of the beam, Mn? O245 ft-k...
A steel cable to be used in a suspension bridge (loaded in tension) must support a...

A steel cable to be used in a suspension bridge (loaded in tension) must support a weight equivalent to 1500 kg. If the elastic limit of the steel to use is σy= 1380 MPa, y and the UTS = 1550 MPa, calculate: a) Minimum diameter of the cable to avoid failure. b) How this diameter must be modified if a security factor of 2.5 is used.
Question 5: Draw a typical stress-strain relationship (graph) for steel subjected to tension. On that graph,...

Question 5: Draw a typical stress-strain relationship (graph) for steel subjected to tension. On that graph, show the initial tangent modulus (slope only), proportional limit, elastic limit, the yield strength, ultimate strength and rupture stress. Also indicate the area that would be used to determine the modulus of resilience. (2+6+3 =11 Points)

6. Plot the stress-strain response that you would expect to see if a specimen of annealed...

6. Plot the stress-strain response that you would expect to see if a specimen of annealed mild steel is subject to uniaxial tension. Indicate the following features on the graph that you draw i). Yield strength ii). Tensile strength iii). Failure strength iv). Failure strain. A sample of the same mild steel was then subject to cold-rolling to produce a 5% reduction in thickness and a second test specimen cut from t. What would the stress-strain response of this deformed...