Homework Answers
Add Answer to:
Question 5: Draw a typical stress-strain relationship (graph) for steel subjected to tension. On that graph,...
Human femur bone was subjected to a uniaxial tension test. As a result of a series...
Human femur bone was subjected to a uniaxial tension test. As a result of a series of experiments, the stress-strain curve shown in Fig. 13.42 was obtained. Based on the graph in Fig. 13.42, determine the following parameters: Elastic modulus, E. Apparent yield strength, sigma _y (use the offset method). Ultimate strength. sigma _u. Strain, epsilon _1, corresponding to yield stress. Strain, epsilon _2, corresponding to ultimate stress. Strain energy when stress is at the proportionality limit.
Will rate if everything is complete. In the space below, sketch the generalized stress-strain behavior for...
Will rate if everything is complete.
In the space below, sketch the generalized stress-strain behavior for a typical metal, such as annealed brass. On your sketch, clearly identify each of the metal, such as annealed brass. On your sketch, clearly identify each of the following. a. 0.2% offset yield strength b. Young's modulus c. Proportional limit d. Ultimate tensile strength Onset of localized plastic deformation е. f. Region of uniform plastic deformation g. Fracture strength h. Ductility i. Toughness Modulus...
2) Draw two schematic graphs using pencil showing a typical stress-strain curve for aluminum. The first...
2) Draw two schematic graphs using pencil showing a typical stress-strain curve for aluminum. The first graph should show engineering stress vs engineering strain, and the second graph should show true stress vs true strain. Label the showing: (i) elastic modulus (ii) proportional limit (iii) yield stress (iv) yield strain (v) fracture stress (vi) fracture strain on each graph. You may show both graphs on one plot. (5 points)
Plz show in graph paper if possible. Thanks :) find stress, strain and draw the graph....
Plz show in graph paper if possible. Thanks :)
find stress, strain and draw the graph. if it is blurry. plz zoom
Part II: Problem 1 (15 points) A tension test was performed on a steel specimen having an original diameter of 12.5 mm and a gauge length of 50 mm. The data is listed in the table below. Plot the stress strain diagram and determine approximately the modulus of elasticity, the yield stress, the ultimate stress, and the rupture...
3. In a stress–strain curve from a tension test, the specimen begins to neck and the...
3. In a stress–strain curve from a tension test, the specimen begins to neck and the elongation between the gage marks is no longer uniform once the load is beyond . a) yield strength b) proportional limit c) ultimate tensile strength d) Fracture stress 4. The two parameters that can define ductility are _____ and _______. a) elongation b) engineering strain c) reduction of area c) poisson’s ratio
1. Stress-Strain Diagrams (10 points) Draw and label a Stress-Strain diagram for two materials with the...
1. Stress-Strain Diagrams (10 points) Draw and label a Stress-Strain diagram for two materials with the following properties. (B) is brittle and has a Young's Modulus that is twice as large as (A). The elastic limit, yield point and rupture occur almost simultaneously for (B). (A) is a ductile material that undergoes plastic deformation prior to rupture. The toughness of (A) is approximately 4x as large as (B). You do not need to label any points on the curves other...
Try to make your answer short and clear to be easier for me to understand, please....
Try
to make your answer short and clear to be easier for me to
understand, please. Thank you
Problem 1 (50 points) Stress Strain Curve Three steel bars with a diameter of 0.5 in, and carbon content of 0.2, 0.5, and 0.8%, respectively The specimens were subjected to tension until rupture. The load versus deformation results were as shown in the table below If the gauge length is 2 in., determine the following a. The tensile stresses and strains for...
Need ASAP, Show all steps. Thanks. Supplemental Problems 10.16 A 12-in.-diameter structural nickel steel specimen was...
Need ASAP, Show all steps. Thanks.
Supplemental Problems 10.16 A 12-in.-diameter structural nickel steel specimen was subjected to a tension test. After rupture it was determined that the 2-in. standard-gage length had stretched to 2.42 in. The minimum diameter at the fracture was measured to be 0.422 in. Compute the percent elongation and percent reduction in area. 10.20 During a tensile test of a steel specimen, the strain at a stress of 35 MPa was calculated to be 0.000 170...
A composite rod is made up of typical structural steel (on the inside) and high strength...
A composite rod is made up of typical structural steel (on the inside) and high strength steel (on the outside). Both steels (in fact all steels) have the same elastic shear modulus G- 80 GPa. The normal steel (inside) has a shear yield stress of 240 MPa. The high strength steel (outside) has a shear yield stress of 480 MPa. The rod is torqued so that the perimeter reaches a shear strain of 0.006. (a) Draw the strain diagram. (b...
1.Below are stress-strain curves for 5 steels. (a) annealed low carbon steel, (b) a steel alloy...
1.Below are stress-strain curves for 5 steels. (a) annealed low carbon steel, (b) a steel alloy which has a DBTT of +50°C (c) 304 stainless steel (d) nearly pure coarse grained Fe Identify the modulus, yield stress, tensile strength, ductility, and toughness. Identify the amount of elastic strain at yield stress, tensile strength, point right before fracture, point right after fracture. 2000 -Low C steel, 1800 steel alloy, DBTT +50C 304 stainless pure Fe 1600 1400 1200 t 1000 800...
Human femur bone was subjected to a uniaxial tension test. As a result of a series of experiments, the stress-strain curve shown in Fig. 13.42 was obtained. Based on the graph in Fig. 13.42, determine the following parameters: Elastic modulus, E. Apparent yield strength, sigma _y (use the offset method). Ultimate strength. sigma _u. Strain, epsilon _1, corresponding to yield stress. Strain, epsilon _2, corresponding to ultimate stress. Strain energy when stress is at the proportionality limit.
Will rate if everything is complete.
In the space below, sketch the generalized stress-strain behavior for a typical metal, such as annealed brass. On your sketch, clearly identify each of the metal, such as annealed brass. On your sketch, clearly identify each of the following. a. 0.2% offset yield strength b. Young's modulus c. Proportional limit d. Ultimate tensile strength Onset of localized plastic deformation е. f. Region of uniform plastic deformation g. Fracture strength h. Ductility i. Toughness Modulus...
2) Draw two schematic graphs using pencil showing a typical stress-strain curve for aluminum. The first graph should show engineering stress vs engineering strain, and the second graph should show true stress vs true strain. Label the showing: (i) elastic modulus (ii) proportional limit (iii) yield stress (iv) yield strain (v) fracture stress (vi) fracture strain on each graph. You may show both graphs on one plot. (5 points)
Plz show in graph paper if possible. Thanks :)
find stress, strain and draw the graph. if it is blurry. plz zoom
Part II: Problem 1 (15 points) A tension test was performed on a steel specimen having an original diameter of 12.5 mm and a gauge length of 50 mm. The data is listed in the table below. Plot the stress strain diagram and determine approximately the modulus of elasticity, the yield stress, the ultimate stress, and the rupture...
1. Stress-Strain Diagrams (10 points) Draw and label a Stress-Strain diagram for two materials with the following properties. (B) is brittle and has a Young's Modulus that is twice as large as (A). The elastic limit, yield point and rupture occur almost simultaneously for (B). (A) is a ductile material that undergoes plastic deformation prior to rupture. The toughness of (A) is approximately 4x as large as (B). You do not need to label any points on the curves other...
Try
to make your answer short and clear to be easier for me to
understand, please. Thank you
Problem 1 (50 points) Stress Strain Curve Three steel bars with a diameter of 0.5 in, and carbon content of 0.2, 0.5, and 0.8%, respectively The specimens were subjected to tension until rupture. The load versus deformation results were as shown in the table below If the gauge length is 2 in., determine the following a. The tensile stresses and strains for...
Need ASAP, Show all steps. Thanks.
Supplemental Problems 10.16 A 12-in.-diameter structural nickel steel specimen was subjected to a tension test. After rupture it was determined that the 2-in. standard-gage length had stretched to 2.42 in. The minimum diameter at the fracture was measured to be 0.422 in. Compute the percent elongation and percent reduction in area. 10.20 During a tensile test of a steel specimen, the strain at a stress of 35 MPa was calculated to be 0.000 170...
A composite rod is made up of typical structural steel (on the inside) and high strength steel (on the outside). Both steels (in fact all steels) have the same elastic shear modulus G- 80 GPa. The normal steel (inside) has a shear yield stress of 240 MPa. The high strength steel (outside) has a shear yield stress of 480 MPa. The rod is torqued so that the perimeter reaches a shear strain of 0.006. (a) Draw the strain diagram. (b...
1.Below are stress-strain curves for 5 steels. (a) annealed low carbon steel, (b) a steel alloy which has a DBTT of +50°C (c) 304 stainless steel (d) nearly pure coarse grained Fe Identify the modulus, yield stress, tensile strength, ductility, and toughness. Identify the amount of elastic strain at yield stress, tensile strength, point right before fracture, point right after fracture. 2000 -Low C steel, 1800 steel alloy, DBTT +50C 304 stainless pure Fe 1600 1400 1200 t 1000 800...
Most questions answered within 3 hours.
-
Is validity and reliability tested by the following methods of
data analysis:
The questionnaires were coded...
asked 5 minutes ago -
whats the relationship between toxoids and clostridium tetani and
botulinum?
asked 4 minutes ago -
1)Explain what it means when demand is inelastic?
2) If demand is elastic, total revenue will...
asked 9 minutes ago -
Jose is making quarterly contributions of of $210 to his savings
account which pays interest at...
asked 8 minutes ago -
Rachel is pushing a box across the floor while Jon, at the same
time, is hoping...
asked 19 minutes ago -
According to the Situational Leadership Model, which of the
following development levels works with a supporting...
asked 22 minutes ago -
The Acme Trucking company has hired you to write software to
help dispatch its trucks. One...
asked 21 minutes ago -
Write a script that uses four separate for loops to output the
following:
1 2 3...
asked 23 minutes ago -
An instructor who taught two sections of engineering statistics
last term, the first with 20 students...
asked 1 hour ago -
A class consists of 15 boys and 12 girls. They want to elect
officers so that...
asked 53 minutes ago -
The mean number of words per minute (WPM) typed by a speed
typist is 79 with...
asked 40 minutes ago -
Write a program with a function named isEqualArr that accepts a
pair of arrays of integers...
asked 1 hour ago