A power electronics converter is made of one MOSFET and one diode. Calculate the system efficiency...
A power electronics converter is made of one MOSFET and one diode. Calculate the system efficiency at f,-100kHz, duty cycle-50%. Here we have: 1) For MOSFET, at the switching moment, switching pattern is shown as below. t-29ns. 3. tr=26ns; 300V 300V 50A 50A 0V OA 0A OV Switching off patterrn Switching on pattern 2) MOSFET on-state resistance is 52mQ; 3) Diode forward voltage is 2.2V@If-50A; 4) diode reverse recovery charge Q2.6uC@IF 50A; 5) Ignore the gate-drive power. 300V
A MOSFET and diode is used in a circuit shown in figure. The operating conditions are as follows: Input Voltage = VIN = 42 V, Io = 5A. Switching frequency fs = 400 kHz, Duty-cycle = D = 0.3. Diode Forward Voltage drop = 0.7V. Diode Peak Reverse Recovery Current = IRRM = 2.5 A. ON-state resistance of the MOSFET is RDS (on) = 25 mΩ. VGG as a step voltage between 0V and 10 V. MOSFET timings – Td...
Given: A MOSFET is used in a switching power-pole found in Fig. 2-4a of the text. The operating conditions are as follows: Vin 35V, 6 A, the switching frequency fs 300 kHz, and the duty ratio d 0.4 a) Consider the diode in the power pole. Assuming an offset voltage forward bias model of the free-wheeling diode in which VM 1.2 V, calculate the average forward power loss in the diode HINT: Consider Eq. 2A-1 b) In the diode reverse...
Design a boost converter power stage to the following specification: Input voltage Output voltage: Output voltage ripple:max 20mV Load power: Switching frequency: 15kHz 110-125V 300V 1.5kW Calculate: (i) Maximum duty cycle (ii) Minimum duty cycle (iii) Average diode current (iv) Assuming the Rds(on) of the MOSFET is 0.01 Ω, and the diode forward voltage is 0.8V, calculate the approximate efficiency of the circuit. 2. A switching power supply shown in the circuit below has its switch driven by a signal...
1. to design a high efficiency d.c. to d.c. power converter with the given specifications Input voltage Output voltage Nominal load current: 4A Inductor current ripple: 0.1A max Switching frequency: 30 kHz Output voltage ripple: 20 mV min 10V max 15V nominal (regulated) 8V Define a suitable power circuit topology to meet the above specification Sketch a circuit diagram of the chosen power circuit topology (a) Define the minimum and maximum duty cycles assuming that the control circuit keeps the...
To design a high efficiency d.c., to d.c power converter with the given specifications min 10V max 15V nominal (regulated) 8V Input voltage: Output voltage: Nominal load current: 4A Inductor current ripple: 0.1A max Switching frequency: 30 kHz Output voltage ripple: 20 mV Define a suitable power circuit topology to meet the above specification? Sketch a circuit diagram of the chosen power circuit topology (a) Define the minimum and maximum duty cycles assuming that the control circuit keeps the output...
Referring to the following data sheets calculate the switching loss for the IGBT: Given, E = 400V, ID= 56A, Fs = 18.5kHz, VDS= 300V, VGS= +/- 18V, RG = 22ohm. Turn-on and Turn-off Energy: IGBT Eon E (mWs) Eoff 20 40 80 100 120 60 Ic (A) SKM50GB063D Values Unit Absolute Maximum Ratings Symbol Conditions IGBT VCES T = 25°C Ic To = 25 °C T = 150°C To = 75 °C Cnom | |сем CRM = 2xl nom 600...