Mainly need help with part (b) please. A rigid bar ABCD is suspended from the ceiling...

Question

Question

Mainly need help with part (b) please.

Answer 1

Answer #1

Answer 2

Similar Homework Help Questions

QUESTION 2 The rigid bar ABCD is pinned at B and supported by two rods, an...

QUESTION 2 The rigid bar ABCD is pinned at B and supported by two rods, an aluminum rod AE and a steel rod CF. Details are given below. aluminum rod AE - E = 10600 ksi L = 24 in d = 0.5 in Om = 40 ksi f-12inte-911-06 All of -15 a STEEL steel rod CF ALMINUM E = L = d = om.x = 30,000 ksi 18 in 0.75 in 50 ksi (a) Determine the maximum force P...
Rigid bar BCD is supported by a pin at C and aluminum rod (1)

Rigid bar BCD is supported by a pin at C and aluminum rod (1). A concentrated load P is applied to the lower end of the aluminum rod (2) which is attached to the rigid bar at D. The cross sectional area of each rod is A»0.20 in2 and the elastic modulus of the aluminum material is E=9200 ksi. The coefficient of thermal expansion 12.5 x 10-6/°F. After the load P is applied and the structure has been CoOLED by...
The assembly, shown below in Figure Q5, consists of three titanium rods and a rigid bar AC, which is horizontal prior to application of the load. The cross-sectional area of each rod is given in Figure Q5. A vertical force, P = 20 kN, is applied to the ri

The assembly, shown below in Figure Q5, consists of three titanium rods and a rigid bar AC, which is horizontal prior to application of the load. The cross-sectional area of each rod is given in Figure Q5. A vertical force, P = 20 kN, is applied to the ring, F, as shown. Given: Eti = 350 GPa. Determine the vertical displacement of point F.

2.5-10 A rigid bar ABCD is pinned at end A and supported by two cables at...

2.5-10 A rigid bar ABCD is pinned at end A and supported by two cables at points B and C (see figure). The cable at B has nominal diameter dB - 12 mm and the cable at C has nominal diameter de 20 mm. A load P acts at end D of the bar. What is the allowable load P if the temperature rises by 60°C and each cable is required to have a factor of safety of at least...
The rigid bar shown is supported by axial bar (1) and by a pin connection at C. Axial bar (1) has...

The rigid bar shown is supported by axial bar (1) and by a pin connection at C. Axial bar (1) has a cross-sectional area of A1 = 250 mm2, an elastic modulus of E = 200 GPa, and a coefficient of thermal expansion of α= 11.3 × 10-6/°C. The pin at C has a diameter of 40 mm. After load P has been applied and the temperature of the entire assembly has been increased by 10°C, the total strain in...
Your answer is partially correct. Try again. A load of P = 50 kN is supported...

Your answer is partially correct. Try again. A load of P = 50 kN is supported by a structure consisting of rigid bar ABC, two identical solid bronze [E = 82 GPa, a = 15.7 x 10-6/0C] rods, and a solid steel [E = 197 GPa, a = 12.2 x 10-6/°C]. The bronze rods (1) each have a diameter of 29 mm and they are symmetrically positioned relative to the center rod (2) and the applied load P. Steel rod...

Item 2 The assembly consists of three titanium (Ti-6A1-4V) rods and a rigid bar AC AAB...

Item 2 The assembly consists of three titanium (Ti-6A1-4V) rods and a rigid bar AC AAB = 1 in Ag = 2 in2in PF. 2t Acb = 1.5 in? 6 ft The cross-sectional area of each rod is given in the figure. A force of P = 76 kip is applied to the ring F. Part A Determine the horizontal displacement of point F. Use Et = 17.4(10) ksi. Express your answer to three significant figures and include appropriate units....
The rigid bar AC is supported by two axial bars (1) and (2). Both axial bars...

The rigid bar AC is supported by two axial bars (1) and (2). Both axial bars are made of bronze [E = 100 GPa; a = 18 x 10-6 mm/mm/°C). The cross-sectional area of bar (1) is A1 = 226 mm- and the cross-sectional area of bar (2) is Az = 362 mm. After load P has been applied and the temperature of the entire assembly has increased by 22°C, the total strain in bar (2) is measured as 1020...
A Review The assembly consists of three titanium (Ti-6A1-4V) rods and a rigid bar AC. 6...

A Review The assembly consists of three titanium (Ti-6A1-4V) rods and a rigid bar AC. 6 ft AAB = 1 in? Agr = 2 in 1 PF-2 Acp = 1.5 in? The cross-sectional area of each rod is given in the figure. A force of P = 53 kip is applied to the ring F. Part A Determine the horizontal displacement of point F. Use Et = 17.4(10%) ksi. Express your answer to three significant figures and include appropriate units....

0.7 mm 6 BL Problem 3 - Thermal Stress (25 pts) The center rod CD of...

0.7 mm 6 BL Problem 3 - Thermal Stress (25 pts) The center rod CD of the assembly is heated from T, = 25°C to T2 = 200°C using electrical resistance heating. At the lower temperature T, the gap between C and the rigid bar is 0.7 mm. Determine the force in the rods AB and EF caused by the increase in temperature. Rods AB and EF are made of steel, and each has a cross-sectional area of 125 mm²....