Problem 4 solution is provided
using this page for the final answers of the following problems i need the right answer...
Do not round intermediate calculations. Give your final answer(s) to three significant figures. Two cylindrical rods, one of steel and the other of brass, are joined at C and restrained by rigid supports at.A and E. For the loading shown and knowing that Es200 GPa and E b 105 GPa, determine the deflection of point C. Dimensions in imm 110 110 190140 D E Steel B Brass 60 KN 45 kN 40-mm diam 30-mm diam.
A solid 70-mm-diameter cold-rolled brass [G = 38.4 GPa] shaft that is 1.13 m long extends through and is completely bonded to a hollow aluminum [G = 25.6 GPa] tube. Aluminum tube (1) has an outside diameter of 98 mm, an inside diameter of 70 mm, and a length of 0.73 m. Both the brass shaft and the aluminum tube are securely attached to the wall support at A. Assume L1=0.73 m, L2=0.4 m, TB=25 kN-m, and TC=7 kN-m. When...
P6.041 A solid 66-mm-diameter cold-rolled brass G = 40.8 GPa) shaft that is 1.22 m long extends through and is completely bonded to a hollow aluminum LG = 27.5 GPa) tube. Aluminum tube (1) has an outside diameter of 89 mm, an inside diameter of 66 mm, and a length of 0.64 m. Both the brass shaft and the aluminum tube are securely attached to the wall support at A. Assume L1=L2 = 0.64 m, L3= 0.58 m, To =...
In the mechanical system represented in Figure 2(a), a motor supplies a torque of 45 kN-m, and powers two machines through gears D and E. The torque delivered to gear E is 8 kN-m The two shafts are made of steel, with E200 GPa, G 80 GPa and yield strength of 300 MPa The shaft AB has an outer diameter of 150 mm and an inner diameter of 80 mm; the shaft DCE has an outer diameter of 80 mm...
this is a multi-parts question. I need all A, B, C, D. Only answer if you know them all. Thx and Will ThumbUp! Problem 3 (10 points) The stepped shaft made of a material having a shear modulus of elasticity G = 40 GPa is fixed at A and loaded by two torques T = 60 N.m and T2= 80 N.m as shown below. The shaft BC has solid circular cross-section with diameter of 50 mm and the shaft AB...
The assembly consists of two red brass C83400 copper rods ABAB and CDCD of diameter 30 mmmm, a stainless 304 steel alloy rod EFEF of diameter 40 mmmm, and a rigid cap GG. The supports at AA, CC and FF are rigid.Modul of elasticy for the copper is EcopperEcopper = 101 GPaGPa. Modul of elasticity for the steel is EsteelEsteel = 193 GPaGPa.(a) Determine the average normal stress developed in the rod ABAB.(b) Determine the average normal stress developed in the rod CDCD.
need help Asap please and thank you The figure illustrates the nonpermanent connection of a steel cylinder head to a grade 30 cast-iron pressure vessel using Nbolts. A confined gasket seal has an effective sealing diameter D. The cylinder stores gas at a maximum pressure Pg For the specifications given in the table for the specific problem assigned, select a suitable bolt length, assuming bolts are available in increments of 5 mm. Then determine the yielding factor of safety np...
Strength of materials I need a solution as soon as possible please For the system shown in Figure (1), the bolt in C is subjected to a single shear and all other bolts are double shear. The diameter of bolt at C is 15 mm, diameter of bolt at D is 10mm and diameter of bolt A is 20mm. The allowable shear stress of bolt C is 200 MPa, allowable shear stress of bolt D is 150 MPa and allowable...
Do not round intermediate calculations. Give your final answer(s) to three significant figures. The aluminum shell is fully bonded to the brass core and the assembly is unstressed at a temperature of 15°C. It is known thatE = 105 GPa and α = 20.9 x 10 /°C for the brass core and E = 74 GPa and α = 23.4 × 10-0/0C for the aluminum shell. Considering only axial deformations, determine the stress in the aluminum when the temperature reaches...
I Solve any five of following questions (show all the necessary steps) and submit until August-01-2020 in PDF file format 1. Draw the shear and bending-moment diagrams for the beam and loading shown below and A B 400 mm 400 mm 250 mm 12 kN 8 KN If the shaft has a diameter of 6cm, Determine the A. Shear forces B. Moment of arms C. The absolute maximum Bending stress in the shaft. 2. Two solid cylindrical rods AB and...