Hello,
Using principle of mass conservation,
Total incoming mass flow rate = total outgoing mass flow rate
i.e.
Thank you
For a given flow chart below, calculate 1-Mass flow rate of Pipe A 2-Mass flow rate...
For a given flow chart below, calculate 1-Mass flow rate of Pipe A 2-Mass flow rate of Pipe B A B с SG: 1.07 D SG: 1.04 D : 10 cm V : 20 m/s SG: 1.065 Q : 1.41m/s V : 12 m/s E SG: 1.15 D : 20 cm V : 25 m/s
For a given flow chart below, calculate 1-Mass flow rate of Pipe A 2-Mass flow rate of Pige A B SG: 1.07 SG: 1.04 D : 10 cm V20 m's D SG : 1.065 O :1.41m's V 12 m/s E SG: 1.15 D 20 cm V : 25 m/s
Problem The relation between pressure drop and flow rate of laminar flows in a pipe is given by l bar 50 m 20° 128u dz PS Flow rate Q is the product of the average velocity and the cross-sectional area of the pipe What is the pressure needed to drive a viscous oil flow upslope through a 12 cm diameter pipe? The length of the pipe is 50 meters. The slope is 20°. At the end of the pipe, the...
The mass flow rate of n-hexane in the pipe is 6.59 g / s. Calculate the flow in the volume in cm ^ 3 / min.
A fresh milk flows in a pipe at a packaging plant with a mass flow rate that would fill 180 1.00-L milk packages per minute. At point 2 in the pipe, the gauge pressure p_2 is 175 kPa and the cross-sectional area A_2 is 10.00 cm^2. At point 1, 1.85 m above point 2, the cross-sectional area A is 3.50 cm^2. The density of milk rho_milk = 1035 kg/m. a) Find volume flow rate V_rate. b) Find the mass flow...
Determine the mass flow rate of water through a pipe with a diameter of 3.3 cm when speed at which water travels through the pipe is 1.5 m/s. kg/s
Question 1: Calculate the flow in each member of the pipe network shown in Figure 2.4 and also the presure difference in N/m' between C and iE. Data for the individual pipes is given in the table below. 360 Ve 300 V E 600 V 460 Va 100 Vs Figure 2.4 UET Pipe Length (m) Diameter (mm)Friction coefficient (l) 530 0.020 460 BC700 530 0.020 CD 610 600 0.022 DE601 600 0.018 EA 150 450 0.018 Hint: Assume initially that...
Calculate the steam mass flow rate in lbm/min; also calculate the exit pipe diameter if the velocity is to be maintained at 7ft/s. Cool water at 60 °F 5 GPM hot water at 20 psig and 180 °F 3 2 Low pressure steam at 20 psig, x=80%
2) In the Figure below, the pipe entrance is sharp-edged. If the flow rate is 0.004 m3/s, what power, in W, is extracted by the turbine? (For water at 20°C, take ρ-998 kg/m3 and μ 0.001 kg/ms. For cast iron, take ε ~ 0.26 mm) Open globe valve Turbine 40 m Water Cast iron: L 125 m, D 5 cm
Given the following data, calculate the mass flow rate of air exiting a pipe. Pipe diameter = 2.47 in. Atmospheric Pressure = 12.38 psia Air Temperature = 61 °F The following total pressure to static pressures differences have been measured. Assume that all measurements were made along a line that passes through the center of the pipe. | Radius (inches) 1.25 1.00 0.75 0.5 0.25 Pressure Difference (psid) 0.012 0.019 0.0204 0.028 0.035 0.039 0.037 0.030 0.021 0.017 0.007 0.25...